Search results

The purpose of this paper is to present and discuss the results of measurements illustrating influence of the area of a thermal pad and the kind of the used base on thermal and optical parameters of LED modules.

LED modules including six power LEDs are designed. In the layout of these modules, different areas of a thermal pad of each LED are used. These modules are made using the classical FR-4 base and metal core printed circuit board (MCPCB). Thermal and optical parameters of all the tested modules are measured using the method elaborated by the authors.

The obtained results of measurements prove that increasing the area of a thermal pad causes a decrease in thermal resistance of the tested LED modules and an increase in power density of the emitted light. The role of the area of a thermal pad is more important for the classical FR-4 base than for MCPCB.

Investigations were performed for only two values of the area of thermal pads and selected values of LEDs forward current.

The presented results of investigations show how the used layout and type of the used base of these modules influence optical and thermal parameters of LED modules. Changing the base of a module can cause even a double decrease in thermal resistance and a double increase in power density of the emitted light.

Surface configuration at the interface between two materials makes a huge difference on thermal resistance. Thermal transient analysis is a powerful tool for thermal characterization of complex structures like LEDs. The purpose of this paper is to report the influence of surface finish on thermal resistance.

Surface of heat sink was modified into two categories: machined as channel like structure; and polished using mechanical polisher and tested with 3W green LED for thermal resistance analysis.

The observed surface roughness of rough and polished surface was 44 nm and 4 nm, respectively. Structure function analysis was used to determine the thermal resistance between heat sink and MCPCB board. The observed thermal resistance from junction to ambient (R_thJA) value measured with thermal paste at 700 mA was lower (34.85 K/W) for channel like surface than rough surface (36.5 K/W). The calculated junction temperature (T_J) for channel like surface and polished surface was 81.29°C and 85.24°C, respectively.

Channelled surface aids in increasing bond line thickness. Surface polishing helps to reduce the air gaps between MCPCB and heat sink and also to increase the surface contact conductance.

The proposed method of surface modification can be easily done at laboratory level with locally available techniques.

Much of the available literature is only concentrating on the design modification and heat transfer from fins to ambient. There was little research on modification of top surface of the heat sink and the proposed concept would give good results and also it will make the material cost reduction as well as material too.

The purpose of this paper is to investigate the thermal behaviors of high power LED packages to enhance the thermal performances of low temperature co‐fired ceramic chip on board (LTCC‐COB) package. Thermal analysis demonstrated an improved LTCC‐COB package design that is comparable to a metal lead frame package with low thermal resistance.

The LED device developed in this study is a LTCC package mounted directly on the metal PCB. A numerical simulation was performed to investigate the thermal characteristics of the LED module using the finite volume method, which is embedded in commercial software (Fluent V.6.3). Thermal resistance and temperature measurement validate the simulated results.

The effect of the thickness of the die attach material on the thermal resistance was dominant due to low thermal conductivity, and the junction temperature decreased significantly with slight increases in thermal conductivity, especially when the value was less than 5 W/mK. The results reveal that the thermal resistance of MCPCB is about 49 per cent‐58 per cent of the junction to board thermal resistance. The thermal model results showed good agreement with experimental results.

The developed model overcomes the large thermal resistance of a conventional LTCC package for high power LED module. The extensive results have demonstrated an improved thermal design, optimal dimensions of each component and boundary conditions for high power LTCC‐COB type package.

Vertical-cavity surface-emitting laser (VCSEL) is a high-performance semiconductor device made of unique epitaxial layers grown on n-type GaAs or InP substrates. The VCSEL’s thermal resistance, Rth, is an essential metric that reflects its thermal properties and dependability. The purpose of this paper is to develop packaging for 1 mm² VCSEL chips made of a variety of materials, such as ceramic, lead frame and printed circuit board (PCB)-based packaging, as well as provide an idea or design that can withstand and perform well in terms of Rth and heat dissipation during operation. SolidWorks 2017 and AutoCAD Mechanical 2017 software were used to publish all thoughts and ideas, including the size dimensions (x, y and z) and material choices for each package.

Following the modelling and material selection, the next step is to use the Ansys Mechanical Structural FEA Analysis software to simulate all packaging for Rth and determine which packaging produced the best result, therefore, determining the heat dissipation for each packing. All parameters were used based on the standard cleanroom requirement for the industrial manufacturing backend process, where the cleanroom classification is 10,000 particles (ISO 7). The results demonstrated that the ceramic and lead frame provided good Rth values of 7.3 and 7.0 K/W, respectively, when compared to the PCB, which provided more than 80 K/W; thus, the heat dissipation for PCB packaging also increased.

As a result of the research, it was determined that ceramic and lead frame packaging are appropriate and capable of delivering good Rth and heat dissipation values when compared to PCB. In comparison to PCB, which requires numerous modifications, such as adding via holes and a thermal bar in an attempt to lower the Rth value, neither packaging requires improvement. Ceramic was chosen for development based on Rth's highest performance, with the actual device consisting of a lead frame and PCB. The Zth measurement test was carried out on a ceramic package, and the Rth result was comparable to the simulation result of 7.6 K/W, indicating that simulation was already proved for research and development.

The purpose of this study is to determine which proposed packaging design would give the highest Rth performance of a 1 mm² chip as well as the best heat dissipation. In comparison to other studies, VCSEL packaging used the header and window cap as package components with a wavelength of 850 nm, and other VCSEL packaging developments used the sub mount on ceramic package with an output power ranging from 500 mW to 2 W, whereas this study used a huge wavelength and an output power of 4 W.

This paper presents the results of the investigations of LED modules soldered with the use of different soldering pastes.

The tested power LED modules are soldered using different solder pastes and soldering processes. Thermal parameters of the performed modules are tested using indirect electrical methods. The results of measurements obtained for different modules are compared and discussed.

It was shown that the soldering process visibly influences the results of measurements of optical and thermal parameters of LED modules. For example, values of thermal resistance of these modules and the efficiency of conversion of electrical energy into light differ between each other even by 15%.

The obtained results of investigations can be usable for designers of the assembly process of power LED modules.

This paper shows the investigations results in the area of effective assembly of power LEDs to the metal core printed circuit board (MCPCB) using different soldering pastes (REL22, REL61, LMPA-Q6, OM-5100, OM-338-PT, M8, OM-340, CVP-390). It was shown that the best thermal and optical properties of these modules are obtained for the OM5100 paste by Alpha Assembly.

One major problem in the lighting industry is the thermal management of the devices. Handling of thermal resistance from solder point to the ambiance of the light-emitting diode (LED) package is linked to the external thermal management that includes a selection of the cooling mode, design of heatsink/substrate and thermal interface material (TIM). Among the significant factors that increase the light output of the of the LED system are efficient substrate and TIM. In this work, the influence of TIM on the luminous flux performance of commercial indium gallium aluminium phosphide (InGaAlP) low-power (LP) LEDs was investigated.

One batch of LEDs was mounted directly onto substrates which were glass-reinforced epoxy (FR4) and aluminium-based metal-core printed circuit boards (MCPCBs) with a dielectric layer of different thermal conductivities. Another batch of LEDs was prepared in a similar way, but a layer of TIM was embedded between the LED package and substrate. The TIMs were thermally conductive epoxy (TCE) and thermally conductive adhesive (TCA). The LED parameters were measured by using the integrated system of thermal transient tester (T3Ster) and thermal-radiometric characterization of LEDs at various input currents.

With the employment of TIM, the authors found that the LED’s maximum luminous flux was significantly higher than the value mentioned in the LED datasheet, and that a significant reduction in thermal resistance and junction temperature was revealed. The results showed that for a system with low thermal resistance, the maximum luminous flux appeared to occur at a higher power level. It was found that the maximum luminous flux was 24.10, 28.40 and 36.00 lm for the LEDs mounted on the FR4 and two MCPCBs, respectively. After TCA application on the LEDs, the maximum luminous flux values were 32.70, 36.60 and 37.60 lm for the FR4 and MCPCBs, respectively. Moreover, the findings demonstrated that the performance of the LED mounted on the FR4 substrate was more affected by the employment of the TIM than that of MCPCBs.

One of the major problems in the lighting industry is the thermal management of the device. In many low-power LED applications, the air gap between the two solder pads is not filled up. Heat flow is restricted by the air gap leading to thermal build-up and higher thermal resistance resulting in lower maximum luminous flux. Among the significant factors that increase the light output of the LED system are efficient substrate and TIM.

The findings in this work can be used as a method to improve thermal management of LP LEDs by applying thermal interface materials that can offer more efficient and brighter LP LEDs. Using aluminium-based substrates can also offer similar benefits.

Users of LP LEDs can benefit from the findings in this work. Brighter automotive lighting (signalling and backlighting) can be achieved, and better automotive lighting can offer better safety for the people on the street, especially during raining and foggy weather. User can also use a lower LED power rating to achieve similar brightness level with LED with higher power rating.

Better thermal management of commercial LP LEDs was achieved with the employment of thermal interface materials resulting in lower thermal resistance, lower junction temperature and brighter LEDs.

This paper aims to present the results of investigations that show the influence of soldering process parameters on the optical and thermal parameters of power LEDs.

The power LEDs were soldered onto metal core printed circuit board (MCPCB) substrates in different soldering ovens: batch and tunnel types, characterized by different thermal profiles. Three types of solder pastes based on Sn99Ag0.3Cu0.7 with the addition of TiO₂ were used. The thermal and optical parameters of the diodes were measured using classical indirect electrical methods. The results of measurements obtained were compared and discussed.

It was shown that the type of oven and soldering thermal profile considerably influence the effectiveness of the removal of heat generated in the LEDs tested. This influence is characterized by thermal resistance changes. The differences between the values of this parameter can exceed 20%. This value also depends on the composition of the soldering paste. The differences between the diodes tested can exceed 15%. It was also shown that the luminous flux emitted by the diode depends on the soldering process used.

The results obtained could be useful for process design engineers for assembling power LEDs for MCPCBs and for designers of solid-state light sources.

This paper presents the results of investigations into the influence of the soldering profiles and soldering pastes used on the effectiveness of the removal of heat generated in power LEDs. It shows and discusses how the factors mentioned above influence the thermal resistance of the LEDs and optical parameters that characterize the light emitted.

Polymer-based thermal interface materials (TIMs) are having pump out problem and could be resolved for reliable application. Solid-based interface materials have been suggested and reported. The purpose of this paper is suggesting thin film-based TIM to sustain the light-emiting diode (LED) performance and electronic device miniaturization.

Consequently, ZnO thin film at various thicknesses was prepared by chemical vapour deposition (CVD) method and tested their thermal behaviour using thermal transient analysis as solid TIM for high-power LED.

Low value in total thermal resistance (R_th-tot) was observed for ZnO thin film boundary condition than bare Al boundary condition. The measured interface (ZnO thin film) resistance {(R_th-bhs) thermal resistance of the interface layer (thin film) placed between metal core printed circuit board (MCPCB) board and Al substrates} was nearly equal to Ag paste boundary condition and showed low values for ZnO film prepared at 30 min process time measured at 700 mA. The T_J value of LED mounted on ZnO thin film (prepared at 30 min.) coated Al substrates was measured to be 74.8°C. High value in junction temperature difference (ΔT_J) of about 4.7°C was noticed with 30 min processed ZnO thin film when compared with Al boundary condition. Low correlated colour temperature and high luminous flux values of tested LED were also observed with ZnO thin film boundary condition (processed at 30 min) compared with both Al substrate and Ag paste boundary condition.

Overall, 30 min CVD processed ZnO thin film would be an alternative for commercial TIM to achieve efficient thermal management. This will increase the life span of the LED as the proposed material decreases the T_J values.

The purpose of this paper is to present an electrothermal model of the module containing power light emitting diodes (LEDs) situated on a common base.

The electrothermal model of this device, which takes into account both self-heating and mutual thermal coupling between the diodes situated in this module, is described.

The correctness of the presented model is verified experimentally, and a good agreement of the calculated and measured optical and thermal characteristics of the considered module is obtained.

The presented model can be used for different structures of the LED module, but electrical inertia in the diodes is omitted.

The presented model was used to calculate electrical, thermal and optical waveforms of the module OSPR3XW1 containing three power LED situated on the common base.

The presented model takes into account thermal inertia in the considered LED module and its cooling systems with mutual thermal coupling between all the diodes situated in the same module.

Optimization of light-emitting diodes’ (LEDs’) design together with long-term reliability is directly correlated with their photometric, electric and thermal characteristics. For a given thermal layout of the LED system, the maximum luminous flux occurs at an optimal electrical input power and can be determined using a photo-electro-thermal (PET) theory. The purpose of this study is to extend the application of the luminous flux equation in PET theory for low-power (LP) LEDs.

LP surface-mounted device LEDs were mounted on substrates of different thermal resistances. Three LEDs were attached to substrates which were flame-retardant fiberglass epoxy (FR4) and two aluminum-based metal core printed circuit boards (MCPCBs) with thermal conductivities of about 1.0 W/m.K, 2.0 W/m.K and 5.0 W/m.K, respectively. The conjunction of thermal transient tester and thermal and radiometric characterization of LEDs system was used to measure the thermal and optical parameters of the LEDs at a certain range of input current and temperature.

The validation of the extended application of the luminous flux equation was confirmed via a good agreement between the practical and theoretical results. The outcomes show that the optimum luminous flux is 25.51, 31.91 and 37.01 lm for the LEDs on the FR4 and the two MCPCBs, respectively. Accordingly, the stipulated maximum electrical input power in the LED datasheet (0.185 W) is shifted to 0.6284, 0.6963 and 0.8838 W between the three substrates.

Using a large number of LP LEDs is preferred than high-power (HP) LEDs for the same system power to augment the heat transfer and provide a higher luminous flux. The PET theory equations have been applied to HP LEDs using heatsinks with various thermal resistances. In this work, the PET theory luminous flux equation was extended to be used for Indium Gallium Aluminum Phosphide LP LEDs attached to the substrates with dissimilar thermal resistances.