Search results

The purpose of this paper is to present an assessment of the ability of combined finite and slab element method (FSEM) for analyzing the wire flat rolling process.

Using the FSEM, the effective strain field of flat rolled wire is predicted for different reductions in height and frictional conditions. The validity of the method is assessed by performing the Vickers microhardness measurements on the flattened wire cross section. Also, the creation of macroscopic shear bands in cross section of the flat rolled wire is investigated and confirmed by microhardness and metallographic examinations. Moreover, the lateral spread and width of contact area are predicted by the FSEM for different reductions in height and frictional conditions.

The FSEM and microhardness results show the minimum and the maximum effective strains at the round edge and center of the flattened wire, respectively. Also, the results show the bands of maximum effective strain at cross section of the flattened wire, i.e. macroscopic shear bands.

This paper can be useful in rolling industries to produce electronic parts, various springs, trolley cables, piston rings, and guide rails.

The paper shows the applicability of the FSEM for calculating the effective strain field and geometry of wire after wire flat rolling process.

The purpose of this paper is to determine the physical design parameters that influence the total resistance of a twisted conductor (cable). One of the physical parameters characterizing this type of structures is the uneven distribution of resistivity due to hardening, which is the result of stress exerted on the wires during the manufacturing process.

The authors have developed a method to take into account the effect of localized hardening on the inhomogeneous distribution of electrical conductivity in the distorted structures of the conductor. To achieve this goal, the authors have implemented a mechanical-electrical simulation method. The resistance characteristics have been measured as a function of mechanical stress.

As demonstrated by the results of measurements conducted on various samples and with various cable design parameters, the resistance of a given material (copper or aluminum), expressed as a function of stress, does not depend on the type of force applied. Therefore, the same characteristics may be applied to various cable designs.

The method presented in this paper enables more detailed investigation of the influence of particular design parameters on the total resistance of a cable. It also provides the ability to determine optimal settings of design parameters.

The approach is distinct from similar studies because it takes into account the deformed geometry of the conductor and the uneven distribution of the resistivity within a filament. In the literature, it is sometimes stated that the distribution of resistivity in a compacted cable is uneven, but its measurement is deemed impossible. This paper provides a method for determining such a distribution.

Friction stir processing (FSP) as a solid-state process has the potential for the production of effective aluminum matrix composites (AMCs). In this investigation, various ceramic particles including B₄C, TiC, SiC, Al₂O₃ and WC were incorporated as the dispersed phase within AA6082 aluminum alloy by FSP. The wear rate of the composite is then investigated experimentally by making use of a design of experiments technique where wear rate is evaluated as the output parameter. The input parameters considered include tool rotational speed, traverse speed, groove width and ceramic particle type. An artificial neural network (ANN) simulation was then used to describe the wear rate of the surface composites. The weights of the network were adjusted to minimize the mean squared error using a feed forward back propagation technique. The effect of the individual input parameters on wear rate was then inferred from the ANN models. Trends are presented and related to the associated microstructures observed. The TiC infused AMC displayed the lowest wear rate whereas the Al₂O₃ infused AMC displayed the highest, within the scope of the current investigation. The paper aims to discuss these issues.

The paper used ANN for the research study.

The finding of this paper is that the wear rate of AA6063 aluminum surface composites is influenced remarkably by FSP parameters.

Original work of authors.

The purpose of this paper is to mainly review the state-of-the-art developments in the field of hydrodynamics of offshore pipelines, identifying the key tools for analysis of pipeline free spans, their applications, their qualifying characteristics and capabilities and limitations.

These different analytical, numerical and semi-empirical tools available for predicting such hydrodynamic loads and their effects include VIVANA, PIPESIN, VIVSIM, SIMULATOR, FATFREE, amongst others. Inherent in these models are current effects, wave effects and/ or pipe–soil interactions.

Amongst these models, the most attention was given to the new VIVANA model because this model take into account the vortex-induced effects with respect to free-spanning pipelines (which have dominant effect in the span analysis in deep water) better than other semi-empirical models (such as Shear 7). Recent improvements in VIVANA include its ability to have arbitrary variation in speed and direction of current, as well as the ability for calculation of pure IL and combined IL-CF response. Improvements in fatigue assessments at free spans, i.e. pipe–soil interaction have been achieved through the combined frequency domain and non-linear time domain analysis methodology adopted. Semi-empirical models are still the de facto currently used in the design of free-spanning pipelines. However, there is need for further research on free-span hydrodynamic coefficients and on how in-line and cross-flow vibrations interact. Again, there is still the challenge due to VIV complexity in fully understanding the fluid structure interaction problem, as there is no consolidated procedure for its analysis. It has been observed that there is large scatter between the different codes adopted in the prediction of fatigue damage, as there lacks full-scale test data devoted to determination/validation of the coefficients used in the semi-empirical models. A case study of the preliminary design of a typical 48 in. pipeline has been presented in this study to demonstrate the use of the free-span analysis tool, DNV RP F105. Excel spreadsheet has been applied in the execution of formulas.

This review paper is the first of its kind to study the state-of-the-art development in pipeline free-span analysis models and demonstrate the use of analysis tool, DNV for MAFSL calculation. Hence, information obtained from this paper would be invaluable in assisting designers both in the industry and academia.

Expert systems are computer-based systems that mimic the logical processes of human experts or organizations to give advice in a specific domain of knowledge. Fuzzy expert systems use fuzzy logic to handle uncertainties generated by imprecise, incomplete and/or vague information. The purpose of this paper is to present a comprehensive review of the methods and applications in fuzzy expert systems.

The authors have carefully reviewed 281 journal publications and 149 conference proceedings published over the past 37 years since 1982. The authors grouped the journal publications and conference proceedings separately accordingly to the methods, application domains, tools and inference systems.

The authors have synthesized the findings and proposed useful suggestions for future research directions. The authors show that the most common use of fuzzy expert systems is in the medical field.

Fuzzy logic can be used to manage uncertainty in expert systems and solve problems that cannot be solved effectively with conventional methods. In this study, the authors present a comprehensive review of the methods and applications in fuzzy expert systems which could be useful for practicing managers developing expert systems under uncertainty.

The purpose of this paper is to optimize the welding parameters: rotating speed and plunging depth of carbon steel and pure copper joints using friction stir spot welding (FSSW) with the aid of the design of experiments (DOE) method.

Carbon steel and pure copper sheets were welded using the FSSW technique with a cylindrical tool and without a probe. The welding parameters were: rotating speed: 1,120, 1,400 and 1,800 RPM and plunging depth: 0.2 and 0.4 mm. The welding process was carried out both with and without pre-heating. The welded specimens were analyzed using a shear tensile test. A microstructural investigation at the optimum conditions was carried out. The results were analyzed and optimized using the statistical software Minitab and following the DOE method.

Pre-heating the sample and increasing the rotating speed and plunging depth increased the tensile shear force of the joint. The plunging depth has the biggest effect on the joint efficiency compared with the rotating speed. The optimum shear force (4,560 N) was found at 1,800 RPM, 0.4 mm plunge depth and with pre-heating. The welding parameters were modified so that the samples were welded at 1,800 RPM and at plunging depths of 0.45–1 mm in 0.05 mm steps. The optimized shear force was 5,400 N. The fractured samples exhibited two types of failure mode: interfacial and nugget pull-out.

For the first time, pure copper and carbon steel sheets were welded using FSSW and a tool without a probe with ideal joint efficiency (95 percent).