Search results

This study aims to investigate the effects of using circular spirals as the longitudinal reinforcing bars on the performance of the concrete beams subjected to four-point bending load.

The effects of using circular spirals as the longitudinal reinforcing bars on the performance of the concrete beams subjected to four-point bending load are investigated in this study. Employing circular spirals as the main longitudinal reinforcement is a novel idea presented in this paper. In this regard, a finite element model of the beam with spiral longitudinal reinforcement was developed. After model verification, several configurations of concrete beams reinforced by longitudinal spirals were simulated under the four-point loading condition.

Obtained results showed that using the longitudinal spirals in place of the conventional longitudinal reinforcing bars can improve the bearing capacity of the concrete beam, but at the same time, increases its ductility unacceptably. In other words, the spirals reduce the initial stiffness of the beam significantly. To solve the problem, the authors decided to use the longitudinal spirals as the auxiliary bars added to the main conventional longitudinal bars in the beams. New gained results were satisfactory. By adding the longitudinal spirals to the conventional bars, not only the bearing capacity of the beam increases between 24% and 63%, but also the initial stiffness and ductility of the beam raises between 11%–29% and 3%–57%, respectively, in comparison to the corresponding beam reinforced with conventional longitudinal bars.

Employing circular spirals as the main longitudinal reinforcement is a novel idea presented in this paper.

Prefabricated pier technology has the advantages of quick construction time, relatively little traffic interference and relatively small environmental impact. However, its applicability under earthquake conditions is not yet fully understood. The seismic performance and influence parameters of a prefabricated concrete pier connected by embedded grouting sleeve (GS) in a pile cap are investigated in this study.

Two prefabricated pier scale model specimens with different reinforcement anchorage lengths and two comparative cast-in-place (CIP) pier model specimens are designed and manufactured for a seismic simulation shaking table. With the continuous increase of input ground motion strength, the changes in basic dynamic characteristics, damage development, acceleration and displacement variation laws, and pier bottom strain responses are compared among the specimen. The finite element software ABAQUS is used to simulate the test pier.

The crack location of the two prefabricated pier specimens is almost the same as that of the CIP pier specimens; CIP pier specimens show more penetrated cracks than prefabricated pier specimens, as well as an earlier crack penetration time. The acceleration, displacement and strain response of the CIP pier specimens are more affected by earthquake activity than those of the prefabricated pier specimens. The acceleration, displacement and strain responses of the two prefabricated piers are nearly identical. The finite element results are in close agreement with the acceleration and displacement response data collected from the test, which verifies the feasibility of the finite element model established in ABAQUS.

A GS connection method is adopted for the prefabricated pier, and on the premise of meeting the minimum reinforcement anchorage length required by the code, this study explores the influences of different reinforcement anchorage lengths on the seismic performance of prefabricated piers in high-intensity areas. A shaking table loading test is used to simulate the real changes of the structure under the earthquake. This work may provide a valuable reference for the design and seismic performance analysis of prefabricated pier, particularly in terms of seismic stability.

There have been limited investigations on the mechanical characteristics of tunnels supported by corrugated plate structures during fault dislocation. The authors obtained circumferential and axial deformations of the spiral corrugated pipe at various fault displacements. Lastly, the authors examined the impact of reinforced spiral stiffness and soil constraints on the support performance of corrugated plate tunnels under fault displacement.

By employing the theory of similarity ratios, the authors conducted model tests on spiral corrugated plate support using loose sand and PVC (polyvinyl chloride) spiral corrugated PE pipes for cross-fault tunnels. Subsequently, the soil spring coefficient for tunnel–soil interaction was determined in accordance with ASCE (American Society of Civil Engineers) specifications. Numerical simulations were performed on spiral corrugated pipes with fault dislocation, and the results were compared with the experimental data, enabling the determination of the variation pattern of the soil spring coefficient.

The findings indicate that the maximum axial tensile and compressive strains occur on both sides of the fault. As the reinforced spiral stiffness reaches a certain threshold, the deformation of the corrugated plate tunnel and the maximum fault displacement stabilize. Furthermore, a stronger soil constraint leads to a lower maximum fault displacement that the tunnel can withstand.

In this study, the calculation formula for density similarity ratio cannot be taken into account due to the limitations of the helical corrugated tube process and the focus on the deformation pattern of helical corrugated tubes under fault action.

This study provides a basis for the mechanical properties of helical corrugated tube tunnels under fault misalignment and offers optimization solutions.

The main goal is to investigate the effect of size and location of opening and column size on the punching shear strength. Openings are often needed in order to install mechanical and electrical services. This process takes away part of the concrete volume which is responsible for resisting the shear forces and any unbalanced moment. Furthermore, the application of rectangular columns in flat slabs is commonly used in practice as they provide lateral stiffness to the building. They are also utilised in garages and multi-storey buildings where these elongated cross-sectional columns reduce the effective span length between adjacent columns.

This research is a numerical-based investigation that is calibrated based on a thirteen previously tested and numerically calibrated slab specimens with no openings. A parametric study is conducted in this study to consider the effect of other parameters, which are the size and location of opening and the rectangularity ratio of column in order to evaluate their effect on the punching shear capacity. A total of 156 models are developed to study these factors. Additionally, the predicted shear carrying capacity of the simulated slabs is calculated using the ACI318–19 and Eurocode (EC2-04) equation.

The presence of openings reduced the punching shear capacity. The small opening's location and orientation have almost no effect except for one slab. For slabs of large openings, the presence of openings reduced the punching capacity. The punching capacity is higher when the openings are farther from the column. The numerically obtained results of slabs with rectangular columns show lower punching capacity compared to slabs of squared columns with the same length of the punching shear control perimeter. The punching capacity for all slabs is predicted by ACI318–19 and Eurocode (EC2-04) and it is found that Eurocode (EC2-04) provided a closer estimation.

The slabs considered for calibration were reinforced with four different punching shear reinforcement configurations, namely; ordinary closed rectangular stirrups, rectangular spiral stirrups, advanced rectangular spiral stirrups and circular spiral. Generally, there has been limited research on concrete flat slabs with openings in comparison with other subjects related to structural engineering (Guan, 2009) and no research on punching shear with openings of slabs reinforced with these reinforcement schemes. The available research focussed on the effects of openings on the flexural behaviour of reinforced concrete slabs includes Casadei et al. (2003), Banu et al. (2012) and Elsayed et al. (2009). In addition, experimental tests that examined slabs supported on rectangular columns are very limited.

The purpose of this paper is to introduce an innovative transversal tubular braid texture and to study the elastic behavior of its 3 D printed structure comparatively to 3 D printed longitudinal tubular braid texture (maypole) to be used as reinforcement.

Regarding the lack of proper machines for the production of the proposed texture, the structure of samples was produced as a tubular lattice braid texture using a 3 D printer with the fused deposition modeling method subsequent to simulation by Rhinoceros software. The produced specimens were composited by polyurethane resin. The composite samples were evaluated by the split disk mechanical test to obtain their hoop stress. The structures of the reinforced composites were theoretically analyzed by ANSYS software.

The results of the mechanical test and theoretical analysis showed that the composites reinforced with transversal tubular lattice braid have higher strength compared to the composites reinforced with longitudinal ones. This assured that the composite reinforced by transversal tubular lattice braid is reliable to be used as high-performance tube for different applications.

Further work is carried out to produce the innovated complex structure continuously by a specially designed machine and fibrous materials to reinforce tubular composites in an industrial continual process to be applied for high-pressure fluids flows.

This paper presents an overview and discusses the applications of fibre reinforced polymer (FRP) bars as reinforcement in civil engineering structures. Following a discussion of the science underpinning their use, selected case studies where FRP reinforcement has been used are presented. The use of FRP reinforcement is rapidly gaining pace and may replace the traditional steel due to its enhanced properties and cost‐effectiveness. In addition, FRP reinforcement offers an effective solution to the problem of steel durability in aggressive environments and where the magnetic or electrical properties of steel are undesirable.

The application of ultra-high performance concrete (UHPC) in anchorage zones can significantly improve the local compression performance of structures. However, the high cost and complex preparation of UHPC make UHPC difficult to be widely used in practice. This study proposes a method to strengthen the local compression zone of structures built by normal strength concrete (NSC) by incorporating UHPC cores.

In this study, a Finite Element Model (FEM) of local compression specimens was established by ABAQUS, and the accuracy of FEM was verified by comparing the FEM calculation results with experimental results. The verified FEM was adapted to the research on the influences of affecting factors on local compression performance of structures, including NSC strength, UHPC strength, spiral steel bar strength, and UHPC core diameter.

The results show that the peak load of the strengthened specimen SC1-U + N increases by 210.2% compared to that of the SC1-NSC. Furthermore, compared to SC1, the strengthened specimen SC1-U + N can save 64.7% amount of UHPC while the peak load decreases by only 34.4%. The peak load of the strengthened specimens increases with the axial compressive strength and the diameter of UHPC cores increasing, crack load increases with increasing the compressive strength of NSC, the spiral steel bar with high strength can prevent the sharp drop of load-deflection curve and the residual bearing capacity increases accordingly. All findings indicate that increasing the diameter of UHPC cores can improve the overall performance of the specimens. Under loading, all specimens fail by following a similar pattern. The effectiveness of this new strengthen method is also verified by FEM analytical calculations.

Based on the experimental study, this study extrapolates the influence of different parameters on the local bearing capacity of the strengthened specimens by finite element simulation. This method not only ensures the accuracy of bearing capacity assessment, but also does not require many samples, which ensures the economy of the reinforcement process. The research results provide a reference for the reinforcement design of anchorage zone.

The calculation and design of the structures are carried out with the aim of obtaining a sufficiently ductile behavior to allow the structure to undergo displacements, without risk of sudden breaks or loss of stability. The purpose of this study is to develop and validate a computer program (Thin beam2), allowing the modeling and simulation of the nonlinear behavior of reinforced concrete elements, on the other part, it is estimating the local and global ductility of the sections or elements constituting these structures.

The authors present two nonlinear analysis methods to carry out a parametric study of the factors influencing the local and global ductility of reinforced concrete structures. The first consists in evaluating the nonlinear behavior at the level of the cross-section of the reinforced concrete elements used in the elaborate Sectenol 1 program, it allows us to have the local ductility. The second, allows us to evaluate the nonlinear behavior of the element used in the modified thin beam 2 program, it allows us to estimate the overall ductility of the element.

The validation results of the Thin beam2 program are very satisfactory, by conferring the analytic and experimental results obtained by various researchers and the parametric study shows that each factor such as the compressive strength of the concrete has a favorable effect on ductility. Conversely, the normal compression force and the high resistance of tensioned reinforcements adversely affect ductility.

The reliability of the two programs lies in obtaining the local and global ductility of reinforced concrete structures because the calculation and design of the structures are carried out with the aim of obtaining ductile behavior without risk of breakage and instability.

The paper aims to introduces an experimental work to investigate the torsional behavior of reinforced concrete (RC) beams strengthened by near-surface mounted (NSM) carbon fiber-reinforced polymer (CFRP) ropes.

In this research, nine rectangular RC beams of 250 mm × 300 mm cross-section and 1,600 mm in length were constructed and tested considering the studied parameters. These parameters include the length of the CFRP rope, the orientation of the CFRP rope, the arrangement of longitudinal and the scheme of NSM-CFRP ropes.

In comparison to control specimens, the results demonstrate a considerable improvement in the torsional response of RC beams strengthened with the CFRP rope. Additionally, specimens strengthened with 90° vertical ropes increase torsional moment capacity more efficiently than specimens strengthened with 45° inclined ropes since the stress concentration leads to premature debonding of the CFRP rope. Whereas RC beams' ability to withstand torsional moments is reduced as the distance between reinforcing CFRP ropes is increased. According to test results, adding CFRP ropes to RC beams' bottoms had a slightly positive impact on torsional response.

This paper fulfills an identified need to study how the using of the CFRP rope is effective in strengthening RC beam subjected to torsion moment.

This paper seeks to understand how software systems and organisations co‐evolve in practice during an IS engagement. Seeks also to argue that complex adaptive system theory (CAS) provides an excellent lens to study the motor of co‐evolution due to its ability to frame the strategies and reinforcement models of actors and to illustrate this by recounting four narratives of the interaction, selection and adaptation of actors arising from a longitudinal case study of an IS engagement. Then sets out to consider how the complexity of the engagement emerges from the interrelationship of these narratives and how the adaptive behaviour of the various actors is both a response to and a driver of co‐evolution within the engagement.

An interpretive case study was undertaken to examine the implementation of a novel academic scheduling and resource allocation system at a research‐intensive Australian university. The research was conducted over ten months, employing ethnographic methods and semi‐structured interviews. This analysis is conducted within the theoretical framework of CAS.

By analysing this case study it is demonstrated how CAS can help designers and managers of IS engagements conceptualise the attendant complexities that they encounter. It is also demonstrated how complexity within IS engagements emerges through the interactions and goal‐seeking behaviour of actors employing a variety of context‐bound strategies within neighbourhoods, and how the adaptive behaviour of the various actors is both a response to and a driver of co‐evolution within the engagement.

This work builds on Organization Science, Vol. 10 Nos 3 and 5, by applying CAS theory to organisational and IS research on co‐evolution, where the findings are grounded in a longitudinal case study and not computational models.