Search results

This paper aims to present a comprehensive review of the laser engineered net shaping (LENS) process in an attempt to provide the reader with a deep understanding of the controllable and fixed build parameters of metallic parts. The authors discuss the effect and interplay between process parameters, including: laser power, scan speed and powder feed rate. Further, the authors show the interplay between process parameters is pivotal in achieving the desired microstructure, macrostructure, geometrical accuracy and mechanical properties.

In this manuscript, the authors review current research examining the process inputs and their influences on the final product when manufacturing with the LENS process. The authors also discuss how these parameters relate to important build aspects such as melt-pool dimensions, the volume of porosity and geometry accuracy.

The authors conclude that studies have greatly enriched the understanding of the LENS build process, however, much studies remains to be done. Importantly, the authors reveal that to date there are a number of detailed theoretical models that predict the end properties of deposition, however, much more study is necessary to allow for reasonable prediction of the build process for standard industrial parts, based on the synchronistic behavior of the input parameters.

This paper intends to raise questions about the possible research areas that could potentially promote the effectiveness of this LENS technology.

The paper seeks to investigate the laser engineered net shaping (LENS) of metal thick‐wall parts from Ni‐based alloy powders.

The composition of Ni‐based alloy powders was determined from phase diagram, which was 84Ni14.4Cu1.6Sn. The powders were prepared by gas atomization. Deoxygenation and screen separation were applied to the powders to improve the sintering ability and narrow the particle size distribution before shaping. Thick‐wall metal parts were built by LENS under different conditions. The microstructures, surface morphologies of the prepared parts were characterized.

The gas atomized powders were almost uniformly spherical after sieving. Most of oxygen contained in the alloy powders could be removed in H₂ atmosphere for heating at 550°C for 2 h. These nickel‐based alloy powders with 150‐200 mesh size were suitable for powder feed system. And these powders were shaped successfully by LENS. Thick‐wall parts with thickness ranged from 20 to 25 mm were fabricated. The thickness of each layer was between 400 and 600 μm by scanning electron microscope. Metallographs revealed that dendritic structures with different characteristics were grown on XY‐, YZ‐ and XZ‐section.

The present experiments were limited by the atmosphere control during the LENS process. The oxide at the interface between two neighbor layers could decrease the mechanical properties if without good inert gas protection, such as a protective atmosphere chamber.

This paper describes a refined experimental program that is needed to resolve the remaining technical issues in LENS of thick‐wall parts. The nickel‐based alloy powders suitable for the LENS process were studied and prepared. After pretreatment, the self‐made powders have good shaping ability. Microstructure features were first discussed with the variation of the face orientation. The dendrite arm distance obtained by this experiment is between 8 and 20 μm, well conforming to the theory. The thick‐wall parts with dense structures were fabricated successfully to widen the field of application of LENS.

The purpose of this paper is to identify if the implementation of ultrasonic vibration in laser engineered net shaping (LENS) process can help to reduce internal weaknesses such as porosity, coarse primary TiB whisker and heterogeneous distribution of TiB reinforcement in the LENS-fabricated TiB reinforced Ti matrix composites (TiB-TMC) parts.

An experimental investigation is performed to achieve the results for comparative studies under different fabrication conditions through quantitative data analysis. An approach of microstructural characterization and mechanical testing is conducted to obtain the output attributes. In addition, the theoretical analysis of the physics of ultrasonic vibration in the melting materials is presented to explain the influences of ultrasonic vibration on the microstructural evolution occurred in the part fabrication.

Because of the nonlinear effects of acoustic streaming and cavitation induced by ultrasonic vibration, porosity is significantly reduced and a relatively small variation of pore sizes is achieved. Ultrasonic vibration also causes the formation of smaller TiB whiskers that distribute along grain boundaries with a homogeneous dispersion. Additionally, a quasi-continuous network (QCN) microstructure is considerably finer than that produced by LENS process without ultrasonic vibration. The refinements of both reinforcing TiB whiskers and QCN microstructural grains further improve the microhardness of TiB-TMC parts.

The novel ultrasonic vibration-assisted (UV-A) LENS process of TiB-TMC is conducted in this work for the first time to improve the process performance and part quality.

The purpose of this paper is to evaluate the feasibility of direct fabrication of lunar/Martian regolith simulant parts, in a freeform environment, using Laser Engineering Net Shaping (LENS™) – an additive manufacturing technology.

Bulk lunar regolith simulant structures were fabricated using a LENS™‐750. Dense parts without any macroscopic defects were produced at a laser power of 50W, a scan speed of 20 mm/s, and a powder feed rate of 12.36 g/min. The laser processed parts were characterized using X‐ray diffraction, differential scanning calorimetry, scanning electron microscope and X‐ray photoelectron spectroscopy to evaluate the influence of laser processing on the microstructure, constituent phases and chemistry of lunar regolith simulant.

A combination of laser parameters resulting in a 2.12 J/mm² laser energy appeared to be ideal for generating a melt pool necessary for lunar regolith powder deposition without excessive liquid pool spreading and cracking of solidified parts. The results show that LENS™ based laser processing transformed crystalline regolith into nanocrystalline and/or amorphous regolith structures as a result of complete melting followed by resolidification. Laser processing also resulted in marginal changes in the composition of the regolith.

Establishment of a lunar/Martian outpost necessitates the development of methods to utilize in situ mineral resources for various construction and resource extraction applications. Fabrication technologies are critical for habitat structure development, as well as repair and replacement of tools and parts at the outpost. Current experimental results presented in the paper clearly demonstrate that net shape regolith simulant parts can be fabricated using LENS™ by exploiting its capabilities.

The purpose of this paper is to investigate how a second-phase doping may affect Al₂O₃ ceramic parts deposited by additive manufacturing (AM) with a laser-engineered net shaping system. Direct fabrication of engineering ceramic components by AM is a relatively new method for producing complex mechanical structures.

In this study, ZrO₂ and Y₂O₃ powders are, respectively, doped into Al₂O₃ powders at the eutectic ratio as second phases to improve the quality of a deposited part. The deposited Al₂O₃, Al₂O₃/ZrO₂ and Al₂O₃/YAG (yttrium aluminum garnet) parts are examined for their micro-structures and micro-hardness, as well as defects.

The experimental results show that doping of ZrO₂ or Y₂O₃ as a second phase performs a significant role in suppressing cracks and in refining grains of the laser-deposited parts. The micro-hardness investigation reveals that the second-phase doping does not result in much hardness reduction in Al₂O₃ and the two eutectic ceramics are both harder than 1,500 Hv.

The study concludes that the second-phase doping of ZrO₂ and Y₂O₃ is good for improving laser-deposited Al₂O₃ ceramic parts.

The purpose of this study is to calibrate a microstructure-based fatigue model for its use in predicting fatigue life of additively manufactured (AM) Ti-6Al-4V. Fatigue models that are capable of better predicting the fatigue behavior of AM metals is required to further the adoption of such metals by various industries. The trustworthiness of AM metallic material is not well characterized, and fatigue models that consider unique microstructure and porosity inherent to AM parts are needed.

Various Ti-6Al-4V samples were additively manufactured using Laser Engineered Net Shaping (LENS), a direct laser deposition method. The porosity within the LENS samples, as well as their subsequent heat treatment, was varied to determine the effects of microstructure and defects on fatigue life. The as-built and heat-treated LENS samples, together with wrought Ti-6Al-4V samples, underwent fatigue testing and microstructure and fractographic inspection. The collected microstructure/defect statistics were used for calibrating a microstructure-sensitive fatigue model.

Fatigue lives of the LENS Ti-6Al-4V samples were found to be consistently less than those of the wrought Ti-6Al-4V samples, and this is attributed to the presence of pores/defects within the LENS material. Results further indicate that LENS Ti-6Al-4V fatigue lives, as predicted by the used microstructure-sensitive fatigue model, are in close agreement with experimental results. The used model could predict upper and lower prediction bounds based on defect statistics. All the fatigue data were found to be within the bounds predicted by the microstructure-sensitive fatigue model.

To further test the utility of microstructure-sensitive fatigue models for predicting fatigue life of AM samples, future studies on additional material types, additive manufacturing processes and heat treatments should be conducted.

This study shows the utility of a microstructure-sensitive fatigue model for use in predicting the fatigue life of LENS Ti-6Al-4V with various levels of porosity and while in a heat-treated condition.

This paper aims to address the numerical simulation of additive manufacturing (AM) processes. The numerical results are compared with the experimental campaign carried out at State Key Laboratory of Solidification Processing laboratories, where a laser solid forming machine, also referred to as laser engineered net shaping, is used to fabricate metal parts directly from computer-aided design models. Ti-6Al-4V metal powder is injected into the molten pool created by a focused, high-energy laser beam and a layer of added material is sinterized according to the laser scanning pattern specified by the user.

The numerical model adopts an apropos finite element (FE) activation technology, which reproduces the same scanning pattern set for the numerical control system of the AM machine. This consists of a complex sequence of polylines, used to define the contour of the component, and hatches patterns to fill the inner section. The full sequence is given through the common layer interface format, a standard format for different manufacturing processes such as rapid prototyping, shape metal deposition or machining processes, among others. The result is a layer-by-layer metal deposition which can be used to build-up complex structures for components such as turbine blades, aircraft stiffeners, cooling systems or medical implants, among others.

Ad hoc FE framework for the numerical simulation of the AM process by metal deposition is introduced. Description of the calibration procedure adopted is presented.

The objectives of this paper are twofold: firstly, this work is intended to calibrate the software for the numerical simulation of the AM process, to achieve high accuracy. Secondly, the sensitivity of the numerical model to the process parameters and modeling data is analyzed.

The purpose of this paper is to review additive and/or subtractive manufacturing methods for metallic objects and their gradual evolution from prototyping tools to rapid manufacture of actual parts.

Various existing rapid manufacturing (RM) methods have been classified into six groups, namely, CNC machining laminated manufacturing, powder‐bed technologies, deposition technologies, hybrid technologies and rapid casting technologies and discussed in detail. The RM methods have been further classified, based on criteria such as material, raw material form, energy source, etc. The process capabilities springing from these classifications are captured in the form of a table, which acts as a database.

Due to the approximation in RM in exchange for total automation, a variety of multi‐faceted and hybrid approaches has to be adopted. This study helps in choosing the appropriate RM process among these myriad technologies.

This review facilitates identification of appropriate RM process for a given situation and sets the framework for design for RM.

The purpose of this paper is to review the state of the art of laser powder deposition (LPD), a solid freeform fabrication technique capable of fabricating fully dense functional items from a wide range of common engineering materials, such as aluminum alloys, steels, titanium alloys, nickel superalloys and refractory materials.

The main R&D efforts and the major issues related to LPD are revisited.

During recent years, a worldwide series of R&D efforts have been undertaken to develop and explore the capabilities of LPD and to tap into the possible cost and time savings and many potential applications that this technology offers.

These R&D efforts have produced a wealth of knowledge, the main points of which are highlighted herein.

This paper aims to present a systematic approach in the literature survey related to metal additive manufacturing (AM) processes and its multi-physics continuum modelling approach for its better understanding.

A systematic review of the literature available in the area of continuum modelling practices adopted for the powder bed fusion (PBF) AM processes for the deposition of powder layer over the substrate along with quantification of residual stress and distortion. Discrete element method (DEM) and finite element method (FEM) approaches have been reviewed for the deposition of powder layer and thermo-mechanical modelling, respectively. Further, thermo-mechanical modelling adopted for the PBF AM process have been discussed in detail with its constituents. Finally, on the basis of prediction through thermo-mechanical models and experimental validation, distortion mitigation/minimisation techniques applied in PBF AM processes have been reviewed to provide a future direction in the field.

The findings of this paper are the future directions for the implementation and modification of the continuum modelling approaches applied to PBF AM processes. On the basis of the extensive review in the domain, gaps are recommended for future work for the betterment of modelling approach.

This paper is limited to review only the modelling approach adopted by the PBF AM processes, i.e. modelling techniques (DEM approach) used for the deposition of powder layer and macro-models at process scale for the prediction of residual stress and distortion in the component. Modelling of microstructure and grain growth has not been included in this paper.

This paper presents an extensive review of the FEM approach adopted for the prediction of residual stress and distortion in the PBF AM processes which sets the platform for the development of distortion mitigation techniques. An extensive review of distortion mitigation techniques has been presented in the last section of the paper, which has not been reviewed yet.