Search results

This paper aims to provide a review on the process of additive manufacturing of ceramic materials, focusing on partial and full melting of ceramic powder by a high-energy laser beam without the use of binders.

Selective laser sintering or melting (SLS/SLM) techniques are first introduced, followed by analysis of results from silica (SiO₂), zirconia (ZrO₂) and ceramic-reinforced metal matrix composites processed by direct laser sintering and melting.

At the current state of technology, it is still a challenge to fabricate dense ceramic components directly using SLS/SLM. Critical challenges encountered during direct laser melting of ceramic will be discussed, including deposition of ceramic powder layer, interaction between laser and powder particles, dynamic melting and consolidation mechanism of the process and the presence of residual stresses in ceramics processed via SLS/SLM.

Despite the challenges, SLS/SLM still has the potential in fabrication of ceramics. Additional research is needed to understand and establish the optimal interaction between the laser beam and ceramic powder bed for full density part fabrication. Looking into the future, other melting-based techniques for ceramic and composites are presented, along with their potential applications.

An experimental and numerical study of thermal profiles of 316 L stainless steel during selective laser melting (SLM) was developed. This study aims to present a novel approach to determine the significance and contribution of thermal numerical modeling enhancement factors of SLM.

Surface and volumetric heat models were proposed to compare the laser interaction with the powder bed and substrate, considering the powder size, absorptance and propagation of the laser energy through the effective depth of the metal layer. The approach consists in evaluating the contribution of the thermal conductivity anisotropic enhancement factors to establish the factors that minimized the error of the predicted results vs the experimental data.

The level of confidence of the carried-out analysis is of 97.8% for the width of the melt pool and of 99.8% for the depth of the melt pool. The enhancement factors of the y and z spatial coordinates influence the most in the predicted melt pool geometry.

Nevertheless, the methodology presented in this study is not limited to 316 L stainless steel and can be applied to any metallic material used for SLM processes.

This study is focused on 316 L stainless steel, which is commonly used in SLM and is considered a durable material for high-temperature, high-corrosion and high-stress situations.

The additive manufacturing (AM) technology is a relatively new technology becoming global. The AM technology may have health benefits when compared to the conventional industrial processes, as the workers avoid extended periods of exposure present in conventional manufacturing.

This study presents a novel approach to determine the significance and contribution of thermal numerical modeling enhancement factors of SLM. It was found that the volumetric heat model and anisotropic enhancement thermal approaches used in the present research, had a good agreement with experimental results.

This paper aims to reduce part defects and improve ceramic additive manufacturing (AM). Selective laser melting (SLM) experiments were carried out to explore the effect of laser power and scanning speed on the microstructure, melting behaviour and surface roughness of cuprous oxide (Cu₂O) ceramic.

The experiments were designed based on varying laser power and scanning speed. The laser power was changed between 50 W and 140 W, and the scanning speed was changed between 170 mm/s and 210 mm/s. Other parameters, such as scanning strategy, layer thickness and hatch spacing, remain constant.

Laser power and scan speed are the two important laser parameters of great significance in the SLM technique that directly affect the molten state of ceramic powders. The findings reveal that Cu₂O part defects are widely controlled by gradually increasing the laser power to 110 W and reducing the scanning speed to 170 mm/s. Furthermore, excessive laser power (>120 W) caused surface roughness, cavities and porous microstructure due to the extremely high energy input of the laser beam.

The SLM technique was used to produce Cu₂O ceramic specimens. SLM of oxide ceramic became feasible using a slurry-based approach. The causes of several part defects such as spattering effect, crack initiation and propagation, the formation of porous microstructure, surface roughness and asymmetrical grain growth during the SLM of cuprous oxide (Cu₂O) are thoroughly investigated.

The purpose of this study is, to compare laser-based additive manufacturing and subtractive methods. Laser-based manufacturing is a widely used, noncontact, advanced manufacturing technique, which can be applied to a very wide range of materials, with particular emphasis on metals. In this paper, the governing principles of both laser-based subtractive of metals (LB-SM) and laser-based powder bed fusion (LB-PBF) of metallic materials are discussed and evaluated in terms of performance and capabilities. Using the principles of both laser-based methods, some new potential hybrid additive manufacturing options are discussed.

Production characteristics, such as surface quality, dimensional accuracy, material range, mechanical properties and applications, are reviewed and discussed. The process parameters for both LB-PBF and LB-SM were identified, and different factors that caused defects in both processes are explored. Advantages, disadvantages and limitations are explained and analyzed to shed light on the process selection for both additive and subtractive processes.

The performance of subtractive and additive processes is highly related to the material properties, such as diffusivity, reflectivity, thermal conductivity as well as laser parameters. LB-PBF has more influential factors affecting the quality of produced parts and is a more complex process. Both LB-SM and LB-PBF are flexible manufacturing methods that can be applied to a wide range of materials; however, they both suffer from low energy efficiency and production rate. These may be useful when producing highly innovative parts detailed, hollow products, such as medical implants.

This paper reviews the literature for both LB-PBF and LB-SM; nevertheless, the main contributions of this paper are twofold. To the best of the authors’ knowledge, this paper is one of the first to discuss the effect of the production process (both additive and subtractive) on the quality of the produced components. Also, some options for the hybrid capability of both LB-PBF and LB-SM are suggested to produce complex components with the desired macro- and microscale features.

To fabricate a selective laser melting (SLM)-processed AlSi10Mg part with almost full density and free of any apparent pores, this study aims to investigate the effect of ambient argon pressure and laser scanning speed on the particles splash during the AlSi10Mg powder bed laser melting.

Based on the discrete element method (DEM), a 3D model of random distribution of powder particles was established, and the 3D free surface of SLM forming process was dynamically tracked by the volume of fluid, where a Gaussian laser beam acts as the energy source melting the powder bed. Through the numerical simulation and process experimental research, the effect of the applied laser power and scanning speed on the operating laser melting temperature was studied.

The process stability has a fundamental role in the porosity formation, which is process-dependent. The effect of the processing conditions on the process stability and the resultant forming defects were clarified.

The results shows that the pores were the main defects present in the SLM-processed AlSi10Mg sample, which decreases the densification level of the sample.

The optimal processing parameters (argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm ) applied during laser melting can improve the quality of selective laser melting of AlSi10Mg,

It can provide a technological support for 3D printing.

Based on the analysis of the pore and balling formation mechanisms, the optimal processing parameters have been obtained, which were argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm. Then, a near-fully dense sample free of any apparent pores on the cross-sectional microstructure was produced by SLM, wherein the relative density of the as-built samples is larger than 97.5%.

This paper aims to propose methods for on-line monitoring and process quality assurance of Selective Laser Melting (SLM) technology as a competitive advantage to enhance its implementation into modern manufacturing industry.

Monitoring of thermal emission from the laser impact zone was carried out by an originally developed pyrometer and a charge-coupled device (CCD) camera which were integrated with the optical system of the PHENIX PM-100 machine. Experiments are performed with variation of the basic process parameters such as powder layer thickness (0-120 μm), hatch distance (60-1,000 μm) and fabrication strategy (the so-called “one-zone” and “two-zone”).

The pyrometer signal from the laser impact zone and the 2D temperature mapping from HAZ are rather sensible to variation of high-temperature phenomena during powder consolidation imposed by variation of the operational parameters.

Pyrometer measurements are in arbitrary units. This limitation is due to the difficulty to integrate diagnostic tools into the optical system of a commercial SLM machine.

Enhancement of SLM process stability and efficiency through comprehensive optical diagnostics and on-line control.

High-temperature phenomena in SLM were monitored coaxially with the laser beam for variation of several operational parameters.

The purpose of this paper is to show the innovative approach of manufacturing filigree and highly complex components by means of laser beam melting.

The paper describes the unique geometric freedom of the laser beam melting technology and its possibility of quick, tool‐less production of complex components allow the manufacturing of functionally superior components in a short time.

Principally concludes the following: additive manufacturing proved to give superior properties to the component compared to conventional manufacturing methods.

This study provides context for the development and manufacturing of an individual heat‐transfer component for an electric‐driven formula race car.

This paper aims to focus on reducing lead-time and energy consumption for laser-based metal deposition of Inconel-625 superalloy and to investigate the effect of process parameters on microstructure, density, surface roughness, dimensional accuracy and microhardness.

Inconel material was deposited on steel substrate by varying process parameters such as laser power, laser scan speed and powder flow rate. The deposited parts were characterized for their density, surface roughness, dimensional accuracy and microhardness.

The study reveals that with increase in laser power, laser scan speed and powder flow rate, there was an increase in density, surface roughness values and microhardness of the deposits, while there was a decrease in dimensional accuracy, deposition time and energy consumption.

The results of this study can be useful in fabrication of Inconel components by laser-based metal deposition process, and the methodology can be expanded to other materials to reduce the lead-time and energy consumption effectively.

The present study gives an understanding of effect of process parameters on density, surface roughness, dimensional accuracy, microhardness, deposition time and energy consumption for laser-based metal deposition of Inconel-625.

Current commercial rapid prototyping systems can be used for fabricating layered models for subsequent creation of fully‐dense metal parts using investment casting. Due to increased demand for shortened product development cycles however, there exists a demand to rapidly fabricate functional fully‐dense metal parts without hard tooling. A possible solution to this problem is direct layered rapid manufacturing of such parts, for example, via laser‐beam fusion of the metal powder. The rapid manufacturing process discussed herein is based on this approach. It involves selective laser‐beam scanning of a predeposited metal‐powder layer, forming fully‐dense claddings as the basic building block of individual layers. This paper specifically addresses only one of the fundamental issues of the rapid manufacturing process under investigation at the University of Toronto, namely the fabrication of single claddings. Our theoretical investigation of the influence of the process parameters on cladding’s geometrical properties employed thermal modeling and computer process simulation. Numerous experiments, involving fabrication of single claddings, were also carried out with varying process parameters. Comparisons of the process simulations and experimental results showed good agreement in terms of overall trends.

Looks at the various applications of the CO₂ gas laser in industrial material processing. Describes how the CO₂ laser beam interacts with particular materials and highlights the laser system configuration, system characteristics and attributes. Details CO₂ laser cutting, welding and surface modification and briefly touches on some emerging aerospace application areas.