Search results

The purpose of this paper is to assess the influence of blends of Jatropha methyl ester (JME) and its nano Al₂O₃ emulsion on variable compression ratio diesel engine. The oxygen in alumina contributed for the smooth burning and resulted in improved performance and emissions.

The biodiesel (methyl ester) is prepared from the raw Jatropha oil. The B10, B20 and B30 blends of and their nanoemulsions are prepared with the 25, 50, 75 and 100 ppm of nano Al₂O₃. The prepared JME blends and its nanoemulsions are tested in a variable compression ratio (VCR) diesel engine to evaluate the engine performance and emission characteristics.

The nanoemulsion B20 + 50 ppm has given maximum brake thermal efficiency (BTE), and with the increased proportion of nanoparticle, the BTE was reduced. Also, the specific fuel consumption is lowest (0.2826 kg/kWh) for B20 + 50 ppm at the compression ratio 16.5 and full load which is 4.10% lower than the diesel and 5.8% lower than the B20 blend. As the load increases, NOx emission increases owing to higher peak temperatures in the combustion chamber. The JME-nano Al₂O₃ emulsion reduces the HC and CO emission compared with all other fuels.

Novel nano emulsions are prepared, characterized and tested on VCR engine.

Compression ignition engines are being used in transportation, agricultural and industrial sectors due to its durability, fuel economy and higher efficiency. This paper aims to present investigation focuses on the utilization of nano additives in emulsified blends of Pongamia biodiesel and its impact on combustion, emission and performance characteristics of a diesel engine.

Pongamia biodiesel was produced through two-stage transesterification process. Taguchi method with L₉ Design of experiment was adopted to study the stability of fuel blends and 75 per cent diesel, 20 per cent biodiesel, 5 per cent water and 6 per cent of surfactant was found to be stable. Further, aluminum oxide nanoparticle was blended into the emulsified fuel in mass fraction of 100 ppm (D75-BD20-W5-S6-AO100) through ultrasonicating technique.

Oleic acid was found to be in prominent proportion in the Pongamia biodiesel. It was observed that D75-BD20-W5-S6 and D75-BD20-W5-S6-AO100 had the ability to produce lower in-cylinder pressure and rate of heat release compared to D100, B100 and D75-BD20 fuel blends. However, a higher rate of pressure rise was noticed in D75-BD20-W5-S6 and D75-BD20-W5-S6-AO100. Lower brake specific fuel consumption and relatively higher brake thermal efficiency were noticed in D75-BD20-W5-S6 and D75-BD20-W5-S6-AO100. Moreover, lower NO_x and smoke emission were also observed for nano-emulsified fuel blends.

Metal-based nano-additive significantly improved the physio-chemical properties of the fuel. Based on the literature, it is understood that emulsified biodiesel blend with nano enrichment using Pongamia biodiesel as base fuel was not carried out. Identifying a stable blend of diesel-biodiesel-water-nano additive using Taguchi’s design of experiments approach was an added value in formulating the test fuels. Furthermore, the formulated test fuel was compared with mineral diesel, biodiesel, and diesel-biodiesel blend to understand its suitability to use as a fuel in compression ignition (CI) engine.

Engine component endurance is related to fuel properties. Decreasing the sulfur content of a fuel reduces its lubricity, thus damaging engines and fuel systems. Therefore, promoting the use of a biofuel must involve assessing the functionality and lubricity of the fuel.

The ball-on-ring (BOR) wear tester was applied to determine the optimal additive concentration and the mechanism of reduction of the wear and friction of the diesel engine fuel injection system. The lubricating efficiency of the fuels was estimated by using a photomicroscope to measure the average diameter of the wear scar produced on the test ball. An optical microscope and scanning electronic microscope were used for wear surface examinations.

The wear test revealed that the wear diameter of the steel ball lubricated with either the pure petrodiesel or 20 Wt.per cent Jatropha curcas biodiesel blends was 1.36 or 1.05 mm, respectively. The experimental results indicated that when Jatropha curcas biodiesel was added into petrodiesels to reduce friction, the wear resistance of the fuel blends increased concurrently with increasing Jatropha curcas biodiesel concentration. This was attributed to the presence of stearic acid in Jatropha curcas biodiesel blends. Stearic acid has a strong affinity for metal surfaces; therefore, a chemical coating was formed between the two motion surfaces to protect the two contacted surfaces from wear. Therefore, the proposed Jatropha curcas biodiesel can be used to effectively enhance the lubricity of a petrodiesel under the condition of boundary lubrication.

Using biofuels as the fuels for diesel engines can assist developed and developing countries in reducing the impacts of their fossil fuel consumption on the environment.

Alternative sources for petroleum fuels have been the prime concern of most of the environmentalists. It is also a concern for economists due to the depletable nature of the fossil fuel. Vegetable oils are considered as good alternatives to diesel as their properties are close to diesel. This work aimed to produce a fuel by adding different proportions of de-oiled neem cake with diesel and to conduct experiments to find out its performance, emission and combustion characteristics.

At present, biodiesel is commercially produced from the vegetable oils by esterification processes. Because most of these oils are edible, its cost restricts the usage. The de-oiled cakes after crushing the seeds containing around 2 per cent of oil with less fatty materials are aimed in this study.

The fuel is prepared by adding dry neem de-oiled cake powder at different proportions ranging from 3 to 25 per cent by weight with diesel. Experimental results reveal that the fuel has the potential to reduce smoke, CO emissions simultaneously along with marginal increase in brake thermal efficiency.

In this published research work, the neem oil is used as biodiesel blends with diesel. Here, the authors have used neem de-oiled cake as a replacement for diesel.

More stringent emission standards are being promulgated all over the world for regulating and decreasing the levels of emission more so caused from on-road vehicles and engines and for improving the air quality problems.

In this study, an attempt has been made to experimentally analyze the performance and emission characteristics of the premixed charge compression ignition (PCCI) mode assisted by a pilot injector.

The results indicate that brake thermal efficiency marginally decreases, and specific fuel consumption increases in all PCCI modes, and HC, CO emissions are higher in the case PCCI modes and oxides of nitrogen and soot levels are considerably reduced in the case of diesel PCCI-biodiesel and petrol PCCI-biodiesel modes.

As obtaining very lean homogenous mixture is hard, it becomes difficult to sustain PCCI mode over the operating range of varying speeds and loads to effectively control the PCCI combustion over the operating range.

Being a responsible human being, we all have the responsibility in keeping this world cleaner, free from all sort of pollution. In this regard, the concept of waste recycling and energy recovery plays a vital role in the development of any economy. This has led to resource conservation and pollution reduction.

The present work Jatropha oil methyl ester (JOME) was chosen as fuels for PCCI mode. Investigations were carried out with blends of JOME with diesel in PCCI combustion mode to evaluate the performance, combustion and emission characteristics of these fuels.

The purpose of this paper is to examine the effects of heat capacity and density of biofuels on aircraft engine performance indicated by thrust and fuel consumption.

The influence of heat capacity and density was examined by simulating biofuels in a two-spool high-bypass turbofan engine running at cruise condition using a Cranfield in-house engine performance computer tool (PYTHIA). The effect of heat capacity and density on engine performance was evaluated through a comparison between kerosene and biofuels. Two types of biofuels were considered: Jatropha Bio-synthetic Paraffinic Kerosene (JSPK) and Camelina Bio-synthetic Paraffinic Kerosene (CSPK).

Results show an increase in engine thrust and a reduction in fuel consumption as the percentage of biofuel in the kerosene/biofuel mixture increases. Besides a low heating value, an effect of heat capacity on increasing engine thrust and an effect of density on reducing engine fuel consumption are observed.

The utilisation of biofuel in aircraft engines may result in reducing over-dependency on crude oil.

This paper observes secondary factors (heat capacity and density) that may influence aircraft engine performance which should be taken into consideration when selecting new fuel for new engine designs.

Vast areas have been studied toward combustion and emission analysis in vegetable oil methyl esters and quite a few in algal oil biodiesel. To analyze the better alternate source for diesel engine, this study aims to investigate the combustion behavior and emission characteristics between cottonseed biodiesel and algal oil biodiesel on comparison with mineral diesel in a compression ignition engine.

The fuel properties like density, kinematic viscosity, calorific value and Cetane number have met the biodiesel standards for both algal and cottonseed biodiesel. At rated power, engine was operated on all three test fuels, where combustion analysis describing in-cylinder pressure, peak pressure, rate of pressure rise and rate of heat release and emission characteristics including hydrocarbon (HC), carbon monoxide (CO), oxides of nitrogen (NOx) and smoke for both biodiesel comparing mineral diesel.

Algal and cottonseed biodiesel showed up to 2-3°CA delayed start of combustion comparing mineral diesel curve. The in-cylinder pressure of algal biodiesel was found to be 68 bar, whereas cottonseed biodiesel exhibited 65 bar at full load condition. Similarly, the rate of pressure rise and rate of heat release of algal biodiesel depicted 7.9 and 10.7 per cent rise than cottonseed biodiesel, respectively. As the load increased, ignition delay showed decreasing trend, while combustion duration showed an increasing trend. HC, CO and smoke emissions were seen to be lower than mineral diesel with noticeable increase in NOx emission.

In this present investigation, biodiesel from Stoechospermum Marginatum, a marine marco algae, was used to fuel the compression ignition engine. Its combustion behavior and emission characteristics are compared with cottonseed biodiesel, a vegetable oil-based biodiesel having similar physio-chemical characteristics to understand the suitability of algal biodiesel in compression ignition engine. This study involves the assessment of straight biodiesel from macro algae and cottonseed oil on standard operating conditions.

This study aims to understand the current production scenario emphasizing the significance of green manufacturing in achieving economic and environmental sustainability goals to fulfil future needs; to determine the viability of particular strategies and actions performed to increase the process efficiency of electrical discharge machining; and to uphold the values of sustainability in the nonconventional manufacturing sector and to identify future works in this regard.

A thorough analysis of numerous experimental studies and findings is conducted. This prominent nontraditional machining process’s potential machinability and sustainability challenges are discussed, along with the current research to alleviate them. The focus is placed on modifications to the dielectric fluid, choosing affordable substitutes and treating consumable tool electrodes.

Trans-esterified vegetable oils, which are biodegradable and can be used as a substitute for conventional dielectric fluids, provide pollution-free machining with enhanced surface finish and material removal rates. Modifying the dielectric fluid with specific nanomaterials could increase the machining rate and demonstrate a decrease in machining flaws such as micropores, globules and microcracks. Tool electrodes subjected to cryogenic treatment have shown reduced tool metal consumption and downtime for the setup.

The findings suggested eco-friendly machining techniques and optimized control settings that reduce energy consumption, lowering operating expenses and carbon footprints. Using eco-friendly dielectrics, including vegetable oils or biodegradable dielectric fluids, might lessen the adverse effects of the electrical discharge machine operations on the environment. Adopting sustainable practices might enhance a business’s reputation with the public, shareholders and clients because sustainability is becoming increasingly significant across various industries.

A detailed general review of green nontraditional electrical discharge machining process is provided, from high-quality indexed journals. The findings and results contemplated in this review paper can lead the research community to collectively apply it in sustainable techniques to enhance machinability and reduce environmental effects.

Depleting reserves of crude oils and their adverse environmental effects have shifted focus toward environment friendly and biobased lubricant base oils. Natural oils and fats act as good lubricants but they have low oxidation and thermal stability which makes them unsuitable for modern day uses. This paper aims to produce trimethylolpropane ester biolubricant from cottonseed oil and study the effects of its use in spark ignition (SI) engines.

In this work, cottonseed oil is converted to TMP lubricant by a two-step based catalyzed esterification. The lubricants thermophysical properties are then analyzed and a 20% blend with synthetic poly-alpha olefin is used in an spark ignition engine.

The produced lubricant has viscosity @100^oC of 4.91 cSt, a viscosity index of 230 and a flash point of 202^oC. When used as a 20% blend in a petrol engine, the rate of oil deterioration was reduced by 18%, however, the overall wear increased by 6.7%. However, this increase is offset by its improved environmental impacts.

In its current state, such a biolubricant can be used as an additive to most commercially available lubricants to improve oil deterioration characteristics and environmental impact. However, further work on improving biolubricant’s wear characteristics is needed for the complete replacement of mineral oil-based lubricants.

This study aims to find a new alternate source for biodiesel conversion. The alternate source must be easily available, and it should give more oil yield than available edible, inedible sources. To meet the fuel demand in the transportation sector with edible oil-based biodiesel causes food versus fuel crisis. In addition to this, it increases NO_x and CO₂ in the environment.

The present paper reviews the comparison of algae oil yield, fatty acid composition and its biodiesel properties’ effect on diesel engine characteristics.

Algae were the only source to fulfil fuel demand because its oil and biodiesel yield is higher than other sources. Algae can grow by capturing carbon dioxide from the environment, and its fatty acid composition is more suitable to run diesel engines.

There is an improvement in engine performance–emission tradeoff with algal biodiesel.