Search results

The purpose of this paper is to present results of an evaluation of dual‐phase and galvanized steel reinforcements in corrosive environments.

Low carbon steels were intercritically annealed at 740°C followed by water quenching to obtain dual‐phase structures with 37 per cent volume fraction of martensite dispersed in ferrite matrix. Dual‐phase and galvanized steel rebars were embedded in concrete cubes and immersed in 5 per cent NaCl solution for up to 100 days. Corrosion rate, tensile and macro as well as microhardness tests were performed. The dual‐phase and galvanized zinc layers were observed under scanning electron microscopy (SEM).

From all of the tests carried out it was found that dual‐phase steels exhibited better corrosion resistant properties and superior strength compared to galvanized steels.

The results reported show that dual‐phase steel can be a good candidate for reinforcement in concrete especially in aggressive and corrosive environments.

The purpose of this paper is to investigate the effect of the soft annealing time on the microstructure and hydrogen embrittlement (HE) of Fe-0.22C-11.54Mn-2.05Al steels.

Steels A and B with different morphologies were prepared by cold rolling after warm rolling, long/short softening annealing and finally annealing at 700 °C for 30 min. Uncharged and charged samples were subjected to tensile, and HE behavior was studied by electron backscattered diffraction, scanning electron microscopy and X-ray diffraction.

The two samples exhibited similar tensile strengths. The homogeneous equiaxed microstructure of steel B was found to be more conducive to relieve its HE sensitivity. Steel A exhibited bimodal-grained microstructures – blocky and lath. The formation of crack in the blocky grains of steel A resulted in a significant reduction in its plasticity and tensile strength.

The high HE susceptibility of steel A is mainly connected with the inhomogeneity of martensite transformation.

Some functional properties of engineering materials, i.e. physical, mechanical and thermal ones, depend directly on the microstructure, which is a result of processes occurring in the material during the forming and thermomechanical processing. The proper microstructure can be obtained in many cases by the phase transformation. This phenomenon is one of the most important processes during hot forming and heat treatment. The purpose of this paper is to develop a new comprehensive hybrid model for modeling diffusion phase transformations. A problem has been divided into several tasks and is carried out on several stages. The purpose of this stage is a development of the structure of a hybrid model, development of an algorithm used in the diffusion module and one-dimensional heat flow and diffusion modeling. Generally, the processes of phase transformations are studied well enough but there are not many tools for their complex simulations. The problems of phase transformation simulation are related to the proper consideration of diffusion, movement of phase boundaries and kinetics of transformation. The proposed new model at the final stage of development will take into account the varying grain growth rate, different shape of growing grains and will allow for proper modeling of heat flow and carbon diffusion during the transformation in many processes, where heating, annealing and cooling can be considered (e.g. homogenizing and normalizing).

One of the most suitable methods for modeling of microstructure evolution during the phase transformation is cellular automata (CA), while lattice Boltzmann method (LBM) suits for modeling of diffusion and heat flow. Then, the proposed new hybrid model is based on CA and LBM methods and uses high performing parallel computations.

The first simulation results obtained for one-dimensional modeling confirm the correctness of interaction between LBM and CA in common numerical solution and the possibility of using these methods for modeling of phase transformations. The advantages of the LBM method can be used for the simulation of heat flow and diffusion during the transformation taking into account the results obtained from the simulations. LBM creates completely new possibilities for modeling of phase transformations in combination with CA.

The studies are focused on diffusion phase transformations in solid state in condition of low cooling rate (e.g. transformation of austenite into ferrite and pearlite) and during the heating and annealing (e.g. transformation of the ferrite-pearlite structure into austenite, the alignment of carbon concentration in austenite and growth of austenite grains) in carbon steels within a wide range of carbon content. The paper presents the comprehensive modeling system, which can operate with the technological processes with phase transformation during heating, annealing or cooling.

A brief review of the modeling of phase transformations and a description of the structure of a new CA and LBM hybrid model and its modules are presented in the paper. In the first stage of model implementation, the one-dimensional LBM model of diffusion and heat flow was developed. The examples of simulation results for several variants of modeling with different boundary conditions are shown.

The key purpose of conducting this review is to identify the issues that affect the structural integrity of pipeline structures. Heat affected zone (HAZ) has been identified as the weak zone in pipeline welds which is prone to have immature failures

In the present work, literature review is conducted on key issues related to the structural integrity of pipeline steel welds. Mechanical and microstructural transformations that take place during welding have been systematically reviewed in the present review paper.

Key findings of the present review underline the role of brittle microstructure phases, and hard secondary particles present in the matrix are responsible for intergranular and intragranular cracks.

The research limitations of the present review are new material characterization techniques that are not available in developing countries.

The practical limitations are new test methodologies and associated cost.

The fracture of pipelines significantly affects the surrounding ecology. The continuous spillage of oil pollutes the land and water of the surroundings.

The present review contains recent and past studies conducted on welded pipeline steel structures. The systematic analysis of studies conducted so far highlights various bottlenecks of the welding methods.

An experimental investigation for developing structure-property correlations of hot-rolled E410 steels with different carbon contents, i.e. 0.04wt.%C and 0.17wt.%C metal active gas (MAG) and cold metal transfer (CMT)-MAG weldments was undertaken.

Mechanical properties and microstructure of MAG and CMT-MAG weldments of two E410 steels with varying content of carbon were compared using standardized mechanical testing procedures, and conventional microscopy.

0.04wt.%C steel had strained ferritic and cementite sub-structures in blocky shape and large dislocation density, while 0.17wt.%C steel consisted of pearlite and polygonal ductile ferrite. This effected yield strength (YS), and microhardness being larger in 0.04wt.%C steel, %elongation being larger in 0.17wt.%C steel. Weldments of both E410 steels obtained with CMT-MAG performed better than MAG in terms of YS, ultimate tensile strength (UTS), %elongation, and toughness. It was due to low heat input of CMT-MAG that resulted in refinement of weld metal, and subzones of heat affected zone (HAZ).

A substantial improvement in YS (∼9%), %elongation (∼38%), and room temperature impact toughness (∼29%) of 0.04wt.%C E410 steel is achieved with CMT-MAG over MAG welding. Almost ∼10, ∼12.5, and ∼16% increment in YS, %elongation, and toughness of 0.17wt.%C E410 steel is observed with CMT-MAG. Relatively low heat input of CMT-MAG leads to development of fine Widmanstätten and acicular ferrite in weld metal and microstructural refinement in HAZ subzones with nearly similar characteristics of base metal.

The purpose of this paper is to discuss the recently developed multi-physics computational model for the conventional Gas Metal Arc Welding (GMAW) joining process that has been upgraded with respect to its predictive capabilities regarding the spatial distribution of the mechanical properties controlling the ballistic limit (i.e. penetration resistance) of the weld.

The original model consists of five modules, each dedicated to handling a specific aspect of the GMAW process, i.e.: electro-dynamics of the welding-gun; radiation-/convection-controlled heat transfer from the electric arc to the workpiece and mass transfer from the filler-metal consumable electrode to the weld; prediction of the temporal evolution and the spatial distribution of thermal and mechanical fields within the weld region during the GMAW joining process; the resulting temporal evolution and spatial distribution of the material microstructure throughout the weld region; and spatial distribution of the as-welded material mechanical properties. The model is upgraded through the introduction of the sixth module in the present work in recognition of the fact that in thick steel GMAW weldments, the overall ballistic performance of the armor may become controlled by the (often inferior) ballistic limits of its weld (fusion and heat-affected) zones.

The upgraded GMAW process model is next applied to the case of butt-welding of MIL A46100 (a prototypical high-hardness armor-grade martensitic steel) workpieces using filler-metal electrodes made of the same material. The predictions of the upgraded GMAW process model pertaining to the spatial distribution of the material microstructure and ballistic-limit-controlling mechanical properties within the MIL A46100 butt-weld are found to be consistent with general expectations and prior observations.

To the authors’ knowledge, the present work is the first reported attempt to establish, using computational modeling, functional relationships between the GMAW process parameters and the mechanical properties controlling the ballistic limit of the resulting weld.

The purpose of this paper is to develop multi-physics computational model for the conventional gas metal arc welding (GMAW) joining process has been improved with respect to its predictive capabilities regarding the spatial distribution of the mechanical properties (strength, in particular) within the weld.

The improved GMAW process model is next applied to the case of butt-welding of MIL A46100 (a prototypical high-hardness armor-grade martensitic steel) workpieces using filler-metal electrodes made of the same material. A critical assessment is conducted of the basic foundation of the model, including its five modules, each dedicated to handling a specific aspect of the GMAW process, i.e.: first, electro-dynamics of the welding-gun; second, radiation/convection controlled heat transfer from the electric arc to the workpiece and mass transfer from the filler-metal consumable electrode to the weld; third, prediction of the temporal evolution and the spatial distribution of thermal and mechanical fields within the weld region during the GMAW joining process; fourth, the resulting temporal evolution and spatial distribution of the material microstructure throughout the weld region; and fifth, spatial distribution of the as-welded material mechanical properties.

The predictions of the improved GMAW process model pertaining to the spatial distribution of the material microstructure and properties within the MIL A46100 butt-weld are found to be consistent with general expectations and prior observations.

To explain microstructure/property relationships within different portions of the weld, advanced physical-metallurgy concepts and principles are identified, and their governing equations parameterized and applied within a post-processing data-reduction procedure.