Search results

Integrated solar combined cycle (ISCC) using parabolic trough collector (PTC) technology is a new power plant that has been installed in few countries to benefit from the use of hybrid solar-gas systems. The purpose of this paper is to investigate the challenges in modeling the thermal output of the hybrid solar-gas power plant and to analyze the factors that influence them.

To validate the proposal, a study was conducted on a test stand in situ and based on the statistical analysis of meteorological data of the year 2017. Such data have been brought from Abener hybrid solar-gas central of Hassi R’mel and used as an input of our model.

The proposal made by the authors has been simulated using MATLAB environment. The simulation results show that the net solar electricity reaches 18 per cent in June, 15 per cent in March and September, while it cannot exceed 8 per cent in December. Moreover, it shows that the power plant responses sensibly to solar energy, where the electricity output increases accordingly to the solar radiation increase. This increase in efficiency results in better economic utilization of the solar PTC equipment in such kind of hybrid solar-gas power plant.

The obtained results would be expected to provide the possibility for designing other power plants in Algeria when such conditions are met (high DNI, low wind speed, water and natural-gas availability).

This paper presents a new model able to predict the thermal solar energy and the net solar-electricity efficiency of such kind solar hybrid power plant.

This paper scrutinizes exergy loss and hydrothermal analysis of Linear Fresnel Reflector (LFR) unit by means of FLUENT. Several mirrors were used to guide the solar radiation inside the receiver, which has parabolic shape. Radiation model was used to simulate radiation mode.

Heat losses from receiver should be minimized to reach the optimized design. Outputs were summarized as contours of incident radiation, isotherm and streamline. Outputs were classified in terms of contours and plots to depict the influence of temperature of hot wall, wind velocity and configurations on performance of Linear Fresnel Reflector (LFR) based on thermal and exergy treatment. Four arrangements for LFR units are considered and all of them have same height.

Greatest Nu and E_x can be obtained for case D due to the highest heat loss from hot wall. Share of radiative heat flux relative to total heat flux is about 94% for case D. In case D when T_r = 0.388, As h_ext rises from 5 to 20, Nu_total enhances about 11.42% when T_r = 0.388. By selecting case D instead of case A, E_x rises about 16.14% for lowest T_r. Nu_total and E_x of case D augment by 3.65 and 6.23 times with rise of T_r when h_ext = 5. To evaluate the thermal performance (η_th) of system, absorber pipe was inserted below the parabolic reflector and 12 mirrors were used above the ground. The outputs revealed that η_th decreases about 14.31% and 2.54% with augment of T_in and Q if other factors are minimum.

This paper scrutinizes exergy loss and hydrothermal analysis of LFR unit by means of finite volume method. Several mirror used to guide the solar radiation inside the receiver, which has parabolic shape. DO model was used to simulate radiation mode. Heat losses from receiver should be minimized to reach the optimized design. Outputs were summarized as contours of incident radiation, isotherm and streamline.

This paper aims to analyze energy and exergy analysis of solar-based intercooled and reheated gas turbine (GT) trigeneration cycle using parabolic trough solar collectors (PTC) with the use of MATLAB 2018.

In the first section of this paper, the solar-based GT is validated with the reference paper. According to the reference paper, the solar field is comprising 30 modules in series and 35 modules in parallel series, where a total of 1,050 modules of PTC are taken into consideration. In the second part of this paper, the hybridization of the solar, GT trigeneration cycle is analyzed and optimized. In the last section of this paper, the hybridization of solar, intercooled and reheated GT trigeneration systems is examined and compared.

The results examined the first section, the power produced by the cycle will be 37.34 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and the efficiencies of energy and exergy will be 38.34% and 39.76%, respectively. The results examined in the second section, the power produced by the cycle will be 38.4 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and accordingly the efficiency of energy and exergy is found to be 40.011% and 41.763%. Where in the last section, the power produced by the cycle will be 41.43 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and the energy and exergy efficiencies will be 39.76% and 40.924%, respectively.

The author confirms that this study is original and has neither been published elsewhere nor it is currently under consideration for publication elsewhere.

To analyze the operating performance of a fuzzy logic control (FLC) based solar energy conversion modular system controlled by a digital signal processor (DSP) microcontroller.

A range of published works relevant to the solar energy conversion modular systems are evaluated and their limitations are indicated in the first section of the paper. The circuit diagram of the panel‐boost converter system is described in the second section. In the third section, a neural network model is suggested for the photovoltaic panel and the model is created in the MATLAB/SIMULINK and then combined with other blocks existing in the system. The design of the FLC method is described in section 4. The simulation and experimental results corresponding to the control of the duty‐cycle of the converter to set the operating point of the solar panel at the maximum power point (MPP) are given in sections 5 and 6, respectively. Section 7, summarizes the results and conclusions of the study.

The paper suggests a simple dc‐dc boost converter controlled by FLC method. The proposed converter model can be used to obtain maximum power from a photovoltaic panel.

In preparing this paper, the resources books existing in the library of our university and the resources relative to the solar energy conversion and FLC published in English language and reachable through the internet were researched.

The paper suggests a neural network model for a solar panel, which can be used in the simulation of the solar energy panel‐boost converter system. The solar energy panel‐boost converter system proposed in this study can be used by the researchers who are working in the solar energy conversion area.

The suggestion of a neural network model for a solar panel and creation of this model in the MATLAB/SIMULINK environment provides researchers to simulate and to analyze the performance of the solar energy panel‐boost converter system using the MATLAB/SIMULINK simulation program. In addition, since the control approach proposed in this paper does not require the information on temperature and solar irradiance that affect the maximum output power, can effectively find the MPP of the solar panel.

This paper aims to propose that the socio-technical perspective is under-represented when appraising the adoption potential of renewable energy technologies (RETs) in late-industrialising countries and that this results in under-adoption. It also aims to identify a methodological approach that allows the socio-technical perspective to be integrated into management decision-making, alongside the more typical economic appraisal methodology.

A case study and novel mixed-methodology approach is used, which applies the diffusion of innovations framework, innovation system (IS) framework and system dynamics modelling (SDM) alongside traditional economic modelling and appraisal techniques. This approach is used to assess the adoption potential of solar photovoltaic (PV) and diesel water pumping systems in the wildlife conservation sector and surrounding rural communities in Kenya. The case study approach tests the merits of the mixed-methodology approach.

The life-cycle costs of solar PV water pumping systems are lower in nearly all financing and utilisation scenarios; offer additional social, technical and environmental benefits; and the conditions exist for greater adoption. The use of an integrated diffusion of innovations and IS framework generates significant qualitative data that can support management decision-making. The use of SDM techniques aid conceptualisation of the community economic, water and institutional systems into which water pumps may be diffused and provide a starting point for formal SDM simulation. The results suggest that these techniques capture the socio-technical perspective well and, when used alongside traditional project appraisal approaches, produce more complete information with which to support management decision-making.

This mixed-methodology approach could be used by practitioners to increase the diffusion and adoption of RETs in more complex contexts in late-industrialising countries. The emergent theory built through the case-study approach should be tested further to assess the merits of applying these techniques to support RET management decision-making in other contexts and more broadly.

Power converters are an integral part of the energy conversion process in solar photovoltaic (PV) systems which is used to match the solar PV generation with the load requirements. The increased penetration of renewable invokes intermittency in the generated power affecting the reliability and continuous energy supply of such converters. DC-DC converters deployed in solar PV systems impose stringent restrictions on supplied power, continuous operation and fault prediction scenarios by continuously observing state variables to ensure continuous operation of the converter.

A converter deployed for a mission-critical application has to ensure continuous regulated output for which the converter has to ensure fault-free operation. The fault diagnostic algorithm relies on the measurement of a state variable to assess the type of fault. In the same line, a predictive controller depends on the measurement of a state variable to predict the control variable of a converter system to regulate the converter output around a fixed or a variable reference. Consequently, both the fault diagnosis and the predictive control algorithms depend on the measurement of a state variable. Once measured, the available data can be used for both algorithms interchangeably.

The objective of this work is to integrate the fault diagnostic and the predictive control algorithms while sharing the measurement requirements of both these control algorithms. The integrated algorithms thus proposed could be applied to any converter with a single inductor in its energy buffer stage.

laboratory prototype is created to verify the feasibility of the integrated predictive control and fault diagnosis algorithm. As the proposed method combine the fault detection algorithm along with predictive control, a load step variation and manual fault creation methods are used to verify the feasibility of the converter as with the simulation analysis. The value for the capacitors and inductors were chosen based on the charge-second and volt-second balance equations obtained from the steady-state analysis of boost converter.

This study aims to propose a methodology by integrating three approaches, namely, internal core technology, external knowledge flow and industrial technology development to help companies improve their decision-making quality for technology planning and enhance their research and development (R&D) portfolio efficiency.

The primary focus of this study is thin-film solar technology and patent data is retrieved from the United States Patent and Trademark Office (USPTO) database. This study presents a methodology based on the proposed integrated analysis method, constructed with patent indicators, centrality analysis of social networks and main path analysis.

The results of this study can be itemized as – the core technological competency: companies involved in two specific technology fields have lower strength in R&D portfolio than leading companies with single-core technology. Knowledge flow: most companies in a network are knowledge producers/absorbers and technological development: diverse source and sink nodes were identified in the global main path during 1997-2003, 2004-2010 and 2011-2017.

Latecomer companies can emulate leaders’ innovation and enhance their technological competence to seek niche technology. Using the global main path, companies monitor outdated technologies that can be replaced by new technologies and aid to plan R&D strategy and implement appropriate strategic decisions avoiding path dependency.

The knowledge accumulation process helps in identifying the change of position and the role of companies; understanding the trend of industrial technology knowledge helps companies to develop new technology and direct strategic decisions. The novelty of this research lies in the integrated approach of three methods aiding industries to find their internal core technical competencies and identify the external position in the competitive market.

The purpose of this paper is to support effective business services provision along the life cycle of complex service-enhanced products, such as the case of solar power plants, and to explore collaborative approaches for multi-stakeholder business services.

Design and implementation of adequate collaboration strategies and cloud-based support mechanisms to facilitate creation and management of collaborative networks in this sector. For this purpose, a conceptual framework, a cloud-based platform and a set of collaboration support tools are proposed. Validation is based on a pilot implementation and interactions with a large group of end users.

Validation results confirmed the suitability of the collaborative networks approach in this sector, which often involves multiple small and medium size enterprises.

The interplay between long-term strategic networks and goal-oriented collaborative networks and their interaction with the various phases of the product-services life cycle correspond to a novel approach in this sector, traditionally focused on a sub-contracting model. This opens new opportunities for enhancing the value of complex products through collaborative value-added services. Of particular relevance is also the adoption of collaborative approaches for service co-creation.

Energy security is a major concern for India and many rural areas remain un-electrified. Thus, innovations in sustainable technologies to provide energy services are required. Biomass and solar energy in particular are resources that are widely available and underutilised in India. This paper aims to provide an overview of a methodology that was developed for designing and assessing the feasibility of a hybrid solar-biomass power plant in Gujarat.

The methodology described is a combination of engineering and business management studies used to evaluate and design solar thermal collectors for specific applications and locations. For the scenario of a hybrid plant, the methodology involved: the analytical hierarchy process, for solar thermal technology selection; a cost-exergy approach, for design optimisation; quality function deployment, for designing and evaluating a novel collector – termed the elevation linear Fresnel reflector (ELFR); and case study simulations, for analysing alternative hybrid plant configurations.

The paper recommended that for a hybrid plant in Gujarat, a linear Fresnel reflector of 14,000 m2 aperture is integrated with a 3 tonne per hour biomass boiler, generating 815 MWh per annum of electricity for nearby villages and 12,450 tonnes of ice per annum for local fisheries and food industries. However, at the expense of a 0.3 ¢/kWh increase in levelised energy costs, the ELFR can increase savings of biomass (100 t/a) and land (9 ha/a).

The research reviewed in this paper is primarily theoretical and further work will need to be undertaken to specify plant details such as piping layout, pump sizing and structure, and assess plant performance during real operational conditions.

The paper considers the methodology adopted proved to be a powerful tool for integrating technology selection, optimisation, design and evaluation and promotes interdisciplinary methods for improving sustainable engineering design and energy management.