Search results
1 – 10 of 776Nikolai Kashaev, Stefan Riekehr, Kay Erdmann, Alexandre Amorim Carvalho, Maxim Nurgaliev, Nikolaos Alexopoulos and Alexandra Karanika
Composite materials and metallic structures already compete for the next generation of single-aisle aircraft. Despite the good mechanical properties of composite materials…
Abstract
Purpose
Composite materials and metallic structures already compete for the next generation of single-aisle aircraft. Despite the good mechanical properties of composite materials metallic structures offer challenging properties and high cost effectiveness via the automation in manufacturing, especially when metallic structures will be welded. In this domain, metallic aircraft structures will require weight savings of approximately 20 per cent to increase the efficiency and reduce the CO2 emission by the same amount. Laser beam welding of high-strength Al-Li alloy AA2198 represents a promising method of providing a breakthrough response to the challenges of lightweight design in aircraft applications. The key factor for the application of laser-welded AA2198 structures is the availability of reliable data for the assessment of their damage tolerance behaviour. The paper aims to discuss these issues.
Design/methodology/approach
In the presented research, the mechanical properties concerning the quasi-static tensile and fracture toughness (R-curve) of laser beam-welded AA2198 butt joints are investigated. In the next step, a systematic analysis to clarify the deformation and fracture behaviour of the laser beam-welded AA2198 four-stringer panels is conducted.
Findings
AA2198 offers better resistance against fracture than the well-known AA2024 alloy. It is possible to weld AA2198 with good results, and the welds also exhibit a higher fracture resistance than AA2024 base material (BM). Welded AA2198 four-stringer panels exhibit a residual strength behaviour superior to that of the flat BM panel.
Originality/value
The present study is undertaken on the third-generation airframe-quality Al-Li alloy AA2198 with the main emphasis to investigate the mechanical fracture behaviour of AA2198 BMs, laser beam-welded joints and laser beam-welded integral structures. Studies investigating the damage tolerance of welded integral structures of Al-Li alloys are scarce.
Details
Keywords
Jeremy Doucet, Xiang Zhang and Philip Irving
This paper aims to present the implementation of a finite element (FE) model used to establish crack and delamination development in a Glare reinforced aluminium plate under…
Abstract
Purpose
This paper aims to present the implementation of a finite element (FE) model used to establish crack and delamination development in a Glare reinforced aluminium plate under fatigue loading. This model predicts the behaviour of bonded GLARE straps used as crack retarders for life extension of aircraft structures. In particular, it takes into account the interaction that exists between the substrate crack and the delamination crack at the interface with the reinforcement.
Design/methodology/approach
In this work, a 3D FE model with three-layer continuum shell elements has been developed to calculate changes in substrate stress intensity and in fatigue crack growth (FCG) rate produced by bonded strap reinforcement. Both circular and elliptical strap delamination geometries were incorporated into the model. Calculated stress intensity factors (SIFs) were used together with measured FCG data for substrate material to predict FCG rates for the strapped condition.
Findings
The model predicted a decrease in the SIF and a retardation of FCG rates. The SIF was predicted to vary through the thickness of the substrate due to the phenomenon of secondary bending and also the bridging effect caused by the presence of the strap. The influence of delamination shape and size on substrate crack stress intensity and delamination strain energy release rate has been calculated.
Originality/value
This research aims at developing modelling techniques that could be used when studying larger reinforced structures found in aircraft.
Details
Keywords
Gives introductory remarks about chapter 1 of this group of 31 papers, from ISEF 1999 Proceedings, in the methodologies for field analysis, in the electromagnetic community…
Abstract
Gives introductory remarks about chapter 1 of this group of 31 papers, from ISEF 1999 Proceedings, in the methodologies for field analysis, in the electromagnetic community. Observes that computer package implementation theory contributes to clarification. Discusses the areas covered by some of the papers ‐ such as artificial intelligence using fuzzy logic. Includes applications such as permanent magnets and looks at eddy current problems. States the finite element method is currently the most popular method used for field computation. Closes by pointing out the amalgam of topics.
Details
Keywords
C.P. Providakis and S.G. Kourtakis
The feasibility of advanced viscoplastic models for non‐linear boundary element analysis of metallic structural components with dependence on thermomechanical history is…
Abstract
The feasibility of advanced viscoplastic models for non‐linear boundary element analysis of metallic structural components with dependence on thermomechanical history is investigated. Several numerical examples are presented using the boundary element implementation of two different internal state variable viscoplastic models to the solution of time‐dependent inelastic problems arising in creeping metallic structural components under the combined action of high temperature loading gradients and quasi‐static mechanical loading conditions. To demonstrate the efficiency of the implemented viscoplastic models, the results obtained using the direct boundary element methodology are compared with those obtained by both analytical and finite element solution as well as, for different numerical results of plane strain thermoviscoplastic deformation problems under general thermomechanical loading.
Details
Keywords
K. Pawluk, U. Krauze and M. Kucharska
Metallic elements placed in the vicinity of coils and conducting rings exert an influence on the inductance of them. Authors' BIMS package based on the boundary‐integral approach…
Abstract
Metallic elements placed in the vicinity of coils and conducting rings exert an influence on the inductance of them. Authors' BIMS package based on the boundary‐integral approach leads up to determine the monopole and/or dipole surface densities of the ‘magnetic charge’ on the walls of simple metallic boxes. The special considerations have been performed in order to study the influence of these boundary magnetic charge densities on the magnetic flux of the coils. The general algorithms for computing the magnetic flux is presented.
Describes preliminary structural design work on a notional uninhabited tactical aircraft (UTA), carried out at Cranfield University. UTAs are seen as an important future element…
Abstract
Describes preliminary structural design work on a notional uninhabited tactical aircraft (UTA), carried out at Cranfield University. UTAs are seen as an important future element of military fleets. A notional baseline requirement was derived, leading to the evolution of a design solution. The basic requirements for such a UTA are naturally highly classified but, although industry has been hesitant to comment, the baseline requirements and design solution developed herein are believed to be reasonable.
Details
Keywords
Giovanni Miano, Fabio Villone and Walter Zamboni
To study optical resonances in metallic nanoparticles.
Abstract
Purpose
To study optical resonances in metallic nanoparticles.
Design/methodology/approach
The metallic nanoparticle is modeled as a dielectric body dispersive in frequency with assigned dielectric constant. The electric field is expressed as function of the charge distribution through an integral formulation. By imposing the boundary conditions on the nanoparticle surface, the equations for the induced charge in the nanoparticle is obtained. The numerical solution of such equations allows to treat arbitrary geometries and to estimate the effects of deviations from ideality on the resonance values.
Findings
Plasmon resonances in metallic nanoparticles can be safely studied with an electro‐quasistatic approximation. The resonance frequencies depend greatly on the details of the geometry of the nanoparticles.
Research limitations/implications
The free‐space wavelength is supposed to be much greater than the largest characteristic dimension of the nanoparticles. Consequently, a electro‐quasistatic model is used to evaluate the distribution of the charges induced in the metallic nanoparticle.
Originality/value
Two methods are presented for the evaluation of the resonance frequencies starting from the numerical solution for a given geometry.
Details
Keywords
Fabio Freschi, Maurizio Repetto, Giambattista Gruosso, Antonio Maffucci, Fabio Villone and Walter Zamboni
To apply two different integral formulations of full‐Maxwell's equations to the numerical study of interconnects in a low‐frequency range and compare the results.
Abstract
Purpose
To apply two different integral formulations of full‐Maxwell's equations to the numerical study of interconnects in a low‐frequency range and compare the results.
Design/methodology/approach
The first approach consists of a surface formulation of the full‐Maxwell's equations in terms of potentials, giving rise to a surface electric field integral equation. The equation, given in a weak form, is solved by using a finite element technique. The solenoidal and non‐solenoidal components of the electric current density are separated using the null‐pinv decomposition to avoid the low‐frequency breakdown. The second model is an extension of partial element equivalent circuit technique to unstructured meshes allowing the use of triangular meshes. Two systems of meshes tied by duality relations are defined on multiconductor systems. The key point in the definition of the equivalent network is to associate the pair primal edge/dual face to a circuit branch. Solution of the resulting electrical network is performed by a modified nodal analysis method and regularization of the outcoming matrix is accomplished by standard techniques based on the addition of suitable resistors.
Findings
Both the formulation have a regular behaviour at very low frequency. This is automatically achieved in the first approach by using the null‐pinv decomposition.
Research limitations/implications
Surface sources of fields.
Originality/value
Two different integral formulations of full‐Maxwell's equations for the numerical study of interconnects are compared in terms of low‐frequency behaviour.
Details
Keywords
Andrea Gaetano Chiariello, Giovanni Miano, Antonio Maffucci, Fabio Villone and Walter Zamboni
To investigate the possible application of carbon nanotubes (CNTs) as interconnects and antennas.
Abstract
Purpose
To investigate the possible application of carbon nanotubes (CNTs) as interconnects and antennas.
Design/methodology/approach
An electromagnetic macroscopic modelling of CNT is derived. The conduction electrons of the nanotube are considered as a 2D fluid moving on the surface representing the positive ion lattice. The linearized Euler's equation describing the fluid motion is used as a macroscopic constitutive relationship to be coupled to Maxwell's equation. A surface integral formulation coupled to the fluid model is solved numerically using a finite element method. For peculiar configurations, transmission line‐like parameters of CNTs are derived.
Findings
Single wall CNT interconnects, due to the high resistance and characteristic impedance with respect to ideally scaled silicon technology, should be used in arrays and bundles.
Research limitations/implications
Only single wall CNTs are considered.
Originality/value
The paper present a novel approach to CNTs and provides a comparison among the behaviour of CNTs with respect to ideally‐scaled silicon technology.
Details