Search results

Purpose – In this research, we have prepared activated carbon (AC) from the waste of banana peels (Musa acuminate L.) using potassium hydroxide (KOH) for carbon monoxide (CO) adsorption from motorcycle gas emission.

Design/Methodology/Approach – The activation was conducted using a chemical activator (KOH) at various concentrations of 1, 2, and 3 N for 1, 2, and 3 h, respectively. Characteristics of banana peels AC (BPAC) produced were analyzed using the Fourier-transform infra-red spectroscopy and scanning electron microscopy.

Findings – Results showed that KOH concentration and activation time strongly affected the CO adsorption and opening of the AC surface pore. There was an increase in the CO sorption when the KOH concentration was increased up to 3 N concentration. The highest CO adsorption from the emission occurred at 70.95% under KOH concentration of 3 N during the 3-h preparation.

Research Limitations/Implications – BPAC has been used as an adsorbent for only CO from motorcycle gas emission but not as an adsorbent for HC, NO, NO_x, or H₂S.

Practical Implications – BPAC can be used as the potential adsorbent for the removal of CO from motorcycle gas emission, and it is an environmental friendly, low cost, and easy to make adsorbent.

Originality/Value – In this study, the AC is made from biomass and is used in wastewater treatment, but limited studies are found on the removal of CO from motorcycle gas emission.

Wide area search munitions (WASMs) are a cross between an unmanned aerial vehicle and a munition. With an impressive array of onboard sensors and autonomous flight capabilities WASMs might play a variety of roles on the modern battle field including reconnaissance, search, battle damage assessment, or communications relay.

Purpose – The purpose of this research is to design and build a wild animal pest repellent device with combination of passive infrared (PIR) sensor and ultrasonic signal based on microcontroller as system controller. The PIR sensor is used to detect the presence of wild animal objects and ultrasonic signals to interfere with the hearing.

Design/Methodology/Approach – The design of the system is built based on microcontroller as the system controller. The system as a whole includes hardware and software. The design of hardware consists of the system design on the transmitter side and the system design on the receiver side, while the software in the of system are algorithms using C language programming.

Findings – The resulting repellent device can detect animals approaching up to a distance of 5 m and may interfere with its hearing with a 40 kHz ultrasonic frequency up to a distance of 20 m. The system also uses remote monitoring devices using 433 MHz radio frequency up to a distance of 60 m.

Research Limitations/Implications – Each animal has different hearing frequencies, as well as some wild animals, but the hearing frequencies of wild animals are generally at ultrasonic frequencies. The frequency of animal hearing may vary from audio frequency to ultrasonic frequency, so ultrasonic wave emission testing with varying frequencies is required.

Practical Implications – This research combines systems on transmitters and receivers, with real-time monitoring of wild animal positions, and it can be possible to monitor the position of more detailed animals by installing more types of sensors as well as increasing the number of sensors.

Originality/Value – This paper may provide additional insight into the hearing frequencies of animals and may also serve as comparable papers for similar studies.

Purpose – The purpose of this study was to determine the efficacy value of national street lighting on energy conservation and carbon dioxide (CO₂) emission reduction.

Design/Methodology/Approach – The methods used are the measurement of electrical parameters (low voltage network), the national road illumination level with SON lamp specification, 400 W, 180 W, and 110 Lumen/W, the simulation of energy conservation calculation, and the CO₂ emission reduction obtained by utilizing panel solar cells as a source of energy and LED lights for illumination.

Finding – The results show the efficacy of a 100-W light bulb at an altitude of 8 m for the following specification of light bulbs: LED, 130 Lumens/W, SON, 110 Lumen/W, and MBF, 53 Lumen/W gives the illumination level respectively 13,913 Lux, 11,773 Lux, and 5,672 Lux. By replacing the 180 W SON lamp with an LED, 100 W, of energy conservation by 3.171 GW h is obtained, which is equivalent to a CO₂ emission reduction of 3.641 kTon CO₂.

Originality/Value – This study is a continuation of a study of energy conservation with the utilization of solar cells as an electrical power source for an LED bulb that replaces low-voltage networks as a power source for the bulb type SON.