Search results

This research outlines the development and characterization of advanced composite materials and their potential applications in the aerospace industry for interior applications. Advanced composites, such as carbon-fiber-reinforced polymers and ceramic matrix composites, offer significant advantages over traditional metallic materials in terms of weight reduction, stiffness and strength. These materials have been used in various aerospace applications, including aircraft, engines and thermal protection systems.

The development of design of experiment–based hybrid aluminum composites using the stir-casting technique has further enhanced the performance and cost-effectiveness of these materials. The design of the experiment was followed to fabricate hybrid composites with nano cerium oxide (nCeO₂) and graphene nanoplatelets (GNPs) as reinforcements in the Al-6061 matrix.

The Al6061 + 3% nCeO2 + 3% GNPs exhibited a high hardness of 119.6 VHN. The ultimate tensile strength and yield strength are 113.666 MPa and 73.08 MPa, respectively. A uniform distribution of reinforcement particulates was achieved with 3 Wt.% of each reinforcement in the matrix material, which is analyzed using scanning electron microscopy. Fractography revealed that brittle and ductile fractures caused the failure of the fractured specimens in the tensile test.

The manufactured aluminum composite can be applied in a range of exterior and interior structural parts like wings, wing boxes, motors, gears, engines, antennas, floor beams, etc. The fan case material of the GEnx engine (currently using carbon-fiber reinforcement plastic) for the Boeing 7E7 can be another replacement with manufactured hybrid aluminum composite, which predicts weight savings per engine of close to 120 kg.

The development of hybrid reinforcements, where two or more types of reinforcements are used in combination, is also a novel approach to improving the properties of these composites. Advanced composite materials are known for their high strength-to-weight ratio. If the newly developed composite material demonstrates superior properties, it can potentially be used to replace traditional materials in aircraft manufacturing. By reducing the weight of aircraft structures, fuel efficiency can be improved, leading to reduced operating costs and environmental impact. This allows for a more customized solution for specific application requirements and can lead to further advancements in materials science and technology.

This study aims to investigate the corrosion behavior of stir-cast hybrid aluminum composite reinforced with CeO₂ and graphene nanoplatelets (GNPs) nanoparticulates used as cylinder liner material in the engines (automotive, aerospace and aircraft industries).

The composites were prepared using the stir-casting technique, and their microstructure and corrosion behavior was evaluated using scanning electron microscopy (SEM) and potentiodynamic polarization test, respectively.

The results showed that the addition of CeO₂ and GNPs improved the corrosion resistance of the composites, and the optimal combination of these two nanoparticles was found to be 3 wt.% CeO₂ and 3 wt.% GNPs. The enhanced corrosion resistance was attributed to the formation of a protective layer on the surface of the composite, as well as the effective dispersion and uniform distribution of nanoparticles in the matrix. The 0.031362 was noted as the lowest corrosion rate (mmpy) and was noticed in 94% Al-6061 alloy + (3 Wt.% CeO₂ + 3 Wt.% GNPs) sample at room temperature and at elevated temperatures; the corrosion rate (mmpy) was observed as 0.0601 and 0.0636 at 45 °C and 75 °C, respectively.

In the vast majority of the published research publications, either cerium oxide or graphene nanoplatelets were utilized as a single reinforcement or in conjunction with other types of reinforcement such as alumina, silicon carbide, carbon nano-tubes, tungsten carbide, etc., but on the combination of the CeO₂ and GNPs as reinforcements have very less literatures with 2 wt.% each only. The prepared hybrid aluminum composite (reinforcing 1 wt.% to 3 wt.% in Al-6061 alloy) was considered for replacing the cylinder liner material in the piston-cylinder arrangement of engines.

The purpose of this study to find an alternate method to minimize waste i.e., eggshell and rice husk ash. In this paper, eggshell (ES) and rice husk ash (RHA) particles are used as reinforcements for examining their effect on the coefficient of thermal expansion (CTE), grain size (GS) and corrosion behavior for developed composite material.

In this investigation, 5 Wt.% each of ES and RHA reinforcement particles have been introduced. To investigate the microstructures of the developed composite material, scanning electron microscope was used. Physical and mechanical properties of composite material are tensile strength and hardness that have been examined.

The result of this paper shows that number of grains per square inch for composition Al/5% ES/5% RHA composite was found to be 1,243. Minimum value of the volume CTE was found to be 6.67 × 10–6/°C for Al/5% ES/5% RHA composite. The distribution of hard phases of ES particles in metal matrix is responsible for improvements in tensile strength and hardness. These findings demonstrated that using carbonized ES as reinforcement provides superior mechanical and physical properties than using uncarbonized ES particles.

There are several articles examining the impact of varying Wt.% of carbonized ES and rice husk reinforcement on the microstructures and mechanical characteristics of metal composites. CTE, GS and corrosion behavior are among of the features that are examined in this paper.

The purpose of this paper is to study Al-based green composite. To make composite samples of aluminium alloy (AA3105) with different weight percentages of rice husk ash (RHA) and eggshell (ES) particles as reinforcement, stir casting method was used.

Several other aspects, including the weight percent of reinforcing agent particles, the applied stress and the sliding speed, were taken into consideration. During the course of the wear test, the sliding distance that was recorded varied from a minimum of 1,000 m all the way up to a maximum of 3,135 m (10, 15, 20, 25 and 30 min). The typical range for normal loads is 8–24 N, and their speed is 1.58 m/s.

With the AA/ES/RHA composite, the wear rates decreases when the grain size of the reinforcing particles enhanced. Scanning electron microscopy images of worn surfaces show that at low speeds, delaminating and ploughing are the main causes of wear. At high speeds, ploughing is major cause of wear. Composites with better wear-resistant properties can be used in wide range of tribological applications, especially in the automotive industry. It was found that hardness increases at the same time as the weight of the reinforcement increases. Tensile and hardness were maximized at 10% reinforcement mix in Al3105.

In this work, ES and RHA has been used to develop green metal matrix composite to support green revolution as promoted/suggested by United Nations thus reducing the environmental pollution.

The purpose of this study is to investigate the impact of titanium oxide (TiO₂) filler on the abrasive wear properties of bamboo fiber reinforced epoxy composites (BFRCs) using a Taguchi approach. The study aims to enhance the abrasive wear resistance of these composites by introducing TiO₂ filler as a potential reinforcement, thus contributing to the development of sustainable and environmentally friendly materials.

This study focuses on the fabrication of epoxy/bamboo composites infused with TiO₂ particles within the Wt.% range of 0–8 Wt.% using hand layup techniques. The resulting composites were subjected to wear testing according to ASTM G99-05 standards. Statistical analysis of the wear results was carried out using the Taguchi design of experiments (DOE). Additionally, an analysis of variance (ANOVA) was used to determine the influential control factors impacting the specific wear rate (SWR) and coefficient of friction (COF).

The study illuminates how integrating TiO₂ filler enhances abrasive wear in epoxy/bamboo composites. Statistical analysis of SWR highlights abrasive grit size (grit) as the most influential factor, followed by normal load, Wt.% of TiO₂ and sliding distance. Analysis of the COF identifies normal load as the primary influential factor, followed by grit, Wt.% of TiO₂ and sliding distance. The Taguchi predictive model closely aligns with experimental results, validating its reliability. The morphological study revealed significant differences between the unfilled and TiO₂-filled composites. The inclusion of TiO₂ improved wear resistance, as evidenced by reduced surface damage and wear debris.

This research paper aims to integrate TiO₂ filler and bamboo fibers to create an innovative hybrid composite material. TiO₂ micro and nanoparticles show promise as filler materials, contributing to improved tribological properties of epoxy composites. The utilization of Taguchi’s DOE and ANOVA for statistical analysis provides valuable guidance for academic researchers and practitioners in optimizing control variables, especially in the context of natural fiber reinforced composites.

This study aims to investigate the optimal process parameters of the wire-cut electrical discharge machining (WCEDM) for the machining of the GZR-AA7475 hybrid metal matrix composite (HMMC). HMMCs are prepared with 2 Wt.% graphite and 4 Wt.% zirconium dioxide reinforced with aluminium alloy 7475 (GZR-AA7475) composite by using the stir casting method. The objective is to enhance the mechanical properties of the material while preserving its unique features. WCEDM with a 0.18 mm molybdenum wire electrode is used for machining the composite.

To conduct experimental studies, a Taguchi L27 orthogonal array was adopted. Input variables such as peak current (I_p), pulse-on-time (T_ON) and flushing pressure (P_F) were used. The effect of process parameters on the output responses, such as material removal rate (MRR), surface roughness rate (SRR) and wire wear ratio (WWR), were investigated. The grey relational analysis (GRA) is used to obtain the optimal combination of the process parameters. Analysis of variance (ANOVA) was also used to identify the significant process parameters affecting the output responses.

Results from the current study concluded that the optimal condition for grey relational grade is obtained at T_ON = 105 µs, I_p = 100 A and P_F = 90 kg/cm². Peak current is the most prominent parameter influencing the MRR, whereas SRR and WRR are highly influenced by flushing pressure.

Identifying the optimal process parameters in WCEDM for machining of GZR-AA7475 HMMC. ANOVA and GRA are used to obtain the optimal combination of the process parameters.

This study aims to investigate the fatigue crack propagation behavior of SiC particle-reinforced 2124 Al alloy composites under constant amplitude axial loading at a stress ratio of R = 0.1. For this purpose, it is performed experiments and comparatively analyze the results by producing 5, 10, 15 Vol.% SiCp-reinforced composites and unreinforced 2124 Al alloy billets with powder metallurgy (PM) production technique.

With the PM production technique, SiCp-reinforced composite and unreinforced 2124 Al alloy billets were produced at 5%, 10%, 15% volume ratios. After the produced billets were extruded and 5 mm thick plates were formed, tensile and fatigue crack propagation compact tensile (CT) samples were prepared. Optical microscope examinations were carried out to determine the microstructural properties of billet and samples. To determine the SiC particle–matrix interactions due to the composite microstructure, unlike the Al alloy, which affects the crack initiation life and crack propagation rate, detailed scanning electron microscopy (SEM) studies have been carried out.

Optical microscope examinations for the determination of the microstructural properties of billet and samples showed that although SiC particles were rarely clustered in the Al alloy matrix, they were generally homogeneously dispersed. Fatigue crack propagation rates were determined experimentally. While the highest crack initiation resistance was achieved at 5% SiC volume ratio, the slowest crack propagation rate in the stable crack propagation region was found in the unreinforced 2124 Al alloy. At volume ratios greater than 5%, the number of crack initiation cycles decreases and the propagation rate increases.

As a requirement of damage tolerance design, the fatigue crack propagation rate and fatigue behavior of materials to be used in high-tech vehicles such as aircraft structural parts should be well characterized. Therefore, safer use of these materials in critical structural parts becomes widespread. In this study, besides measuring fatigue crack propagation rates, the mechanisms causing crack acceleration or deceleration were determined by applying detailed SEM examinations.

The purpose of this study is to investigate the effect of the sintering temperature on the microstructural, mechanical and physical properties of Cu-SiC composites.

The powder metallurgy route was used to fabricate the samples. Cold compaction of powders was conducted at 250 MPa which was followed by sintering at 850°C–950°C at the interval of 50 °C in the open atmospheric furnace. SiC was used as a reinforcement and the volumetric fraction of the SiC was varied as 10%, 15% and 20%. The processed samples were metallurgically characterized by the scanning electron microscope (SEM). Mechanical characterization was done using tensile and Vickers’ micro-hardness testing to check the hardness and strength of the samples. Archimedes principle and Four-point collinear probe method were used to measure the density and electrical resistivity of the samples.

SEM micrograph reveals the uniform dispersion of the SiC particles in the Cu matrix element. The results revealed that the Hardness and tensile strength were improved due to the addition of SiC and were maximum for the samples sintered at 950 °C. The addition of SiC has also increased the electrical resistivity of the Cu-SiC composite and was lowest for Cu 100% while the relative density has shown the reverse trend. Further, it was found that the maximum hardness of 91.67 Hv and ultimate tensile strength of 312.93 MPa were found for Cu-20% SiC composite and the lowest electrical resistivity of 2.017 µ- Ω-cm was found for pure Cu sample sintered at 950 °C, and this temperature was concluded as the optimum sintering temperature.

The powder metallurgy route for the fabrication of the composites is a challenging task as the trapping of oxygen cannot be controlled during the compaction process as well as during the sintering process. So, a more intensive study is required to overcome these kinds of limitations.

As of the author’s best knowledge, no work has been reported on the effect of sintering temperature on the properties of the Cu-SiC composites which has huge potential in the industries.

This study aims to deal with developing composite filaments and investigating the tribological behavior of additively manufactured syntactic foam composites. The primary objective is to examine the suitability of the cenosphere (CS; 0–30 Wt.%) to develop a high-quality lightweight composite structure with improved abrasion strength.

CS/polyethylene terephthalate glycol (PETG) composite feedstock filaments under optimized extrusion conditions were developed, and a fused filament fabrication process was used to prepare CS-filled PETG composite structures under optimal printing conditions. Significant parameters such as CS (0–30 Wt.%), sliding speed (200–800 rpm) and typical load (10–40 N) were used to minimize the dry sliding wear rate and coefficient of friction for developed composites.

The friction coefficient and specific wear rate (SWR) are most affected by the CS weight percentage and applied load, respectively. However, nozzle temperature has the least effect on the friction coefficient and SWR. A mathematical model predicts the composite material’s SWR and coefficient of friction with 87.5% and 95.2% accuracy, respectively.

Because of their tailorable physical and mechanical properties, CS/PETG lightweight composite structures can be used in low-density and damage-tolerance applications.

CS, an industrial waste material, is used to develop lightweight syntactic foam composites for advanced engineering applications.

CS-reinforced PETG composite filaments were developed to fabricate ultra-light composite structures through a 3D printing routine.

The purpose of this study is to investigate and evaluate the impact of varying proportions of reinforcement on the mechanical properties of a modified Al₂O₃-LM6 cast composite under self-pouring temperature conditions. This study aims to determine the optimal mixture proportion of fine powders of Al, Si and xAl₂O₃ (with x values of 2%, 3% and 4%) through the application of design of experiment (DoE) and statistical analysis using the Minitab software. This study also involved evaluating the microstructural estimation and other physical properties of the cast composite to understand the combined effect of the reinforcement proportion on the material’s properties.

The researchers initially mixed the powders through ball milling and then compacted the moisture-free powder mix in a closed steel die. The resulting preforms were heated at the self-pouring temperature in an inert environment to fabricate the final cast composite. By applying DoE and performing an analysis of variance (ANOVA), the researchers sought to optimize the mixture proportion that would yield the best mechanical properties.

The experimental results indicated that a mixture combination of 83.5% Al blended with 12.5% Si and 4% Al₂O₃ led to the greatest improvement in mechanical properties, specifically in terms of increased density, hardness and impact strength. The ANOVA further supported the interaction effect of each processing parameter on the observed results. The results of this study offer valuable insights for the fabrication of modified Al₂O₃-LM6 cast composites under self-pouring temperature conditions. The identified optimal mixture proportion provides guidance for manufacturing processes and material selection to achieve improved mechanical properties in similar applications.

This study focuses on a specific composite material consisting of modified Al₂O₃ and LM6. Although Al₂O₃ and LM6 have been studied individually in various contexts, the combination of these materials and their impact on mechanical properties under self-pouring temperature conditions is a novel aspect of this research. The researchers use DoE methodology, along with statistical analysis using Minitab software, to optimize the mixture proportion and analyze the data. This systematic approach allows for a comprehensive exploration of the parameter space and the identification of significant factors that influence the mechanical properties of the composite.