Search results

The purpose of this paper is to report the preparation, characterisation and machinability of resin hybrid GFRP composites, which are made of glass fibre and the mixture of epoxy & polyester resin.

Resin hybrid GFRP laminates containing 0, 20 and 40wt% of polyester resin with the epoxy resin are prepared by conventional hand layup technique using glass fibre as the reinforcement. The variation of break load and shear strength for three different combinations of epoxy and polyester resin are studied by ASTM. A plan of experiment based on Taguchi was established with prefixed cutting parameters and the machining was performed. A stylus type profilometer to examine the surface roughness and shop microscope to examine the delamination of resin hybrid GFRP laminates were used. An analysis of variance (ANOVA) was performed to investigate the cutting characteristics of resin hybrid GFRP composite materials using solid carbide end mill. The correlation was obtained by multiple‐variable linear regression using Minitab 14 software.

Taguchi analysis reveals that the resin hybrid GFRP laminate provides better machinability in terms of surface roughness and delamination when compared to homogenous GFRP laminates (pure epoxy resin). Polyester resin enhances the machinability of the GFRP laminates.

The machinability of the resin hybrid GFRP laminates can be improved further by modifying the polyester resin percentage.

The resin hybrid GFRP laminates so developed can be used in aircraft and aerospace applications to increase the shear and work of fracture properties.

The purpose of this study was to carry out the analysis of impact resistance for aluminum hybrid laminates and polymer matrix composites reinforced with glass and carbon fibers. Damage modes and damages process under varied impact energies are also presented and discussed.

The subject of examination were fiber metal laminates – FMLs (Al/CFRP and Al/GFRP). The samples were subjected to low-velocity impact by using a drop-weight impact tester. The specimens after impact were examined using non-destructive and destructive inspection techniques.

The hybrid laminates are characterized by higher resistance to impact in comparison to the conventional laminates. The delaminations between composite layers as well as the delaminations on metal/composite interface and lateral cracks are the prevailing type of destruction mechanisms. No significant relationships between metal volume friction coefficient vs response to the impact were recorded for the hybrid laminates under tests.

The understanding of impact behavior of FMLs is particularly important for selecting these materials and their designing, in damage tolerance philosophy aspect in aerospace industry as well as in searching the methods of predicting of FML hybrid materials resistance to impact. The test results might be useful for the validation of simulations using numerical methods.

The paper presents the impact resistance of new hybrid laminates for aerospace applications. The identification of damage character and failure mechanisms as well as the relationships between damage and impact responses of aluminum/carbon and aluminum/glass hybrid laminates were estimated.

The purpose of this paper is to perform a numerical analysis on the static and dynamic behaviors of beams made up of functionally graded carbon nanotube (FG-CNT) reinforced polymer and hybrid laminated composite containing the layers of carbon reinforced polymer with CNT. Conventional fibers have higher density as compared to carbon nanotubes (CNTs), thus insertion of FG-CNT reinforced polymer layer in fiber reinforced composite (FRC) structures makes them sustainable candidate for weight critical applications.

In this context, stress and strain formulations of a multi-layer composite system is determined with the help of Timoshenko hypothesis and then the principle of virtual work is employed to derive the governing equations of motion. Herein, extended rule of mixture and conventional micromechanics relations are used to evaluate the material properties of carbon nanotube reinforced composite (CNTRC) layer and FRC layer, respectively. A generalized eigenvalue problem is formulated using finite element approach and is solved for single layer FG-CNTRC beam and multi-layer laminated hybrid composite beam by a user-interactive MATLAB code.

First, the natural frequencies of FG-CNTRC beam are computed and compared with previously available results as well as with Ritz approximation outcomes. Further, free vibration, bending, and buckling analysis is carried out for FG-CNTRC beam to interpret the effect of different CNT volume fraction, number of walls in nanotube, distribution profiles, boundary conditions, and beam-slenderness ratios.

A free vibration analysis of hybrid laminated composite beam with two different layer stacking sequence is performed to present the advantages of hybrid laminated beam over the conventional FRC beam.

The purpose of this paper is to analyze the significance of disparate design variables on the mechanical properties of the composite laminate. Four design variables such as stacking sequence, stacking angle, types of resins and thickness of laminate have been chosen to analyze the impact on mechanical properties of the composite laminate. The detailed investigation is carried out to analyze the effect of a carbon layer in stacking sequence and investigate the impact of various resins on the fastening strength of fibers, stacking angles of the fibers and the thickness of the laminate.

The Taguchi approach has been adopted to detect the most significant design variable for optimum mechanical properties of the hybrid composite laminate. For this intend, L16 orthogonal array has been composed in statistical software Minitab 17. To investigate an effect of design variables on mechanical properties, signal to noise ratio plots were developed in Minitab. The numerical analysis was done by using the analysis of variance.

The single parameter optimization gives the optimal combination A₁B₁C₄D₂ (i.e. stacking sequence C/G/G/G, stacking angle is 00, the type of resin is newly developed resin [NDR] and laminate thickness is 0.3 cm) for tensile strength; A₄B₂C₄D₂ (i.e. stacking sequence G/G/G/C, stacking angle is 450, the type of resin is NDR and laminate thickness is 0.3 cm) for shear strength; and A₂B₃C₄D₂ (i.e. stacking sequence G/C/G/G, stacking angle is 900, the type of resin is NDR and thickness is 0.3 cm) for flexural strength. The types of resins and stacking angles are the most significant design variables on the mechanical properties of the composite laminate.

The novelty in this study is the development of new resin called NDR from polyethylene and polyurea group. The comparative study was carried out between NDR and three conventional resins (i.e. polyester, vinyl ester and epoxy). The NDR gives higher fastening strength to the fibers. Field emission scanning electron microscope images illustrate the better fastening ability of NDR compared with epoxy. The NDR provides an excellent strengthening effect on the RCC beam structure along with carbon fiber (Figure 2).

The study aims to investigate the influence of fabric hybridization, stacking sequences and matrix materials on the tensile strength and damping behavior of jute/carbon reinforced hybrid composites.

The hybrid composites were fabricated with different sequences of fabric plies in epoxy and polyester matrix using a hand layup technique. The tensile and vibration characteristics were evaluated on the hybrid laminated composite models using finite element analysis (FEA), and the results were validated experimentally according to ASTM standards. The surface morphology of the fractured specimens was studied using the scanning electron microscope.

The experimental results revealed that the position of jute layers in the hybrid composites has a significant influence on the tensile strength and damping behavior. The hybrid composite with jute fiber at the surface sides and carbon fibers at the middle exhibited higher tensile strength with superior damping properties. Further, it is found that the experimental results are in good coherence with the FEA results.

The less weight and low-cost hybrid composites were fabricated by incorporating the jute and carbon fabrics in interply configurations. The influences of fabric hybridization, stacking arrangements and matrix materials on the tensile and vibration behavior of jute/carbon hybrid composites have been numerically evaluated and the results were experimentally validated.

A growing response in the development of hybrid composites to conquer the deficiency of neat composites has provoked doing this work. Thermoplastic Polycarbonate material offers better impact toughness with low structural weight. There is a little/no information available over the selected sandwich hybrid composite prepared from woven E-Glass and polycarbonate sheet. The purpose of this paper is to understand the response of the novel hybrid structure under tensile, flexural, interlaminar shear and impact loading conditions.

The hand-layup technique is used for fabricating the hybrid composites in the laminate configuration. The hybrid composites are prepared with a total fiber content of 70 percent weight fractions. The effect of the percentage of reinforcement on mechanical properties is evaluated experimentally as per American society for testing materials standard test methods. The damaged mechanisms of failed samples and fractured surfaces are well analyzed using vision measuring system and scanning electron microscopy.

A decline in densities of hybrid composites up to 22.5 percent is noticed with reference to neat composite. An increase in impact toughness up to 40.73 percent is marked for hybrid laminates owing to the ductile nature of PC. Delamination is identified to be the major mode of failure apart from fiber fracture/pull-out, matrix cracking in all the static loading conditions.

The response of novel hybrid composite reported has been explored for the first time in this paper. The outcome of experimental work revealed that hybridization offered lightweight structures with improved transverse impact toughness as compared to conventional composite.

This paper aims to deal with the influence of cutting parameters on drill thrust force, delamination and surface roughness in the drilling of laminated jute/carbon hybrid composites.

The hybrid composites were fabricated with four layers of fabrics, which are arranged in different sequences using the hand-layup technique. Drilling experiments involved drilling of 6 mm diameter holes on the prepared composite plates using high-speed steel and solid carbide drill materials. Analysis of variance was used to find the influence, percentage contribution and significance of drilling parameters on drilling-induced damages. Scanning electron microscopy analysis was also conducted to understand the fracture behavior and surface morphology of the drilled holes.

The experimental study reveals that the most significant effect was the feed rate influenced the drill thrust force and the drill speed influenced both delamination factor and surface roughness of hybrid fiber-reinforced composites. From observations, the suggested combination for drilling jute/carbon hybrid composites is carbide drill, spindle speed of 1,750 rpm and feed of 0.03 mm/rev.

The new lightweight and low-cost hybrid composites were developed by hybridizing jute with carbon fabrics in the epoxy matrix with interplay arrangements. The influence of cutting speed and feed rate on delamination damage and surface roughness in the drilling of hybrid composites have been experimentally evaluated.

The purpose of this study is to investigate the results of reinforcing fibre metal laminates with glass fibres under low-cycle fatigue conditions in a limited number of cycles.

The tests were carried out on open-hole rectangular specimens loaded in tension-tension at high load ranges of 80 and 85 per cent of maximum force determined in static test, correspondingly. The number of cycles for destruction has been determined experimentally.

By means of microscopic observations, it was possible to determine the moment of crack initiation and their growth rate. Furthermore, it was possible to identify the impact of reinforcing fibre orientation in composite layers, material creating the metal layers, on fatigue life and on nature of crack propagation.

This work validates the possibility of increasing the resistance of fibre metal laminates to low-cycle fatigue by modifying the structure of the laminate.

The resistance of fibre metal laminates on low-cycle fatigue is not widely described and the phenomena occurring during degradation are poorly understood.

This study aims to demonstrate the numerical application of differential quadrature (DQ) methods and show the experimental application of free vibration analysis of fiber-metal laminated composite (FML) plates with various boundary conditions.

The FMLs are hybrid structures consisting of fiber-reinforced polymer matrix composites such as carbon, glass, aramid and different metal sheets, and are currently widely used in the automobile, aircraft and aerospace industries. Thus, free vibration analysis of these hybrid materials is necessary for the design process. The governing equations of motion are derived based on the classical plate theory. The DQ, generalized DQ (GDQ) and harmonic DQ (HDQ) differential quadrature methods have been used to solve the governing equations of an FML composite plate numerically. The accuracy and convergence of the numerical model have been verified by comparing the results available in the published literature with the results obtained from these methods. Moreover, an experimental procedure has been performed in order to compare the results against those of the numerical methods.

It is noteworthy that a high degree of similarity and accuracy was observed between the numerical results obtained by the DQ methods and the experimental results. Thus, the present study validates the applicability of the DQ methods for designing the FML composite plates.

In this study, the advantages of the DQ methods have been demonstrated differently from previous studies on the vibration analysis of the FML plates.

A bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view is given. The bibliography at the end of the paper contains 1,726 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1996‐1999.