Search results

The purpose of this paper is to propose a novel hybrid excitation permanent magnet synchronous generator (HEPMSG) utilizing tooth harmonic for excitation, the structural features and operation principle of which are also described.

To obtain the operation performance quickly, this paper derives the mathematical model of the machine system represented by circuit, and analyzes the operation mode of rectifier circuit in the tooth harmonic excitation system, then the standard state equations for each operation mode are obtained. Combining the inductance parameter of this machine with the load resistance and inductance, the armature current waveform, the field current waveform and tooth harmonic winding current waveform are obtained by using the numerical method to solve the standard state equation.

Comparing with the experimental results, the availability of the principle and the validity of the model of the machine system are verified.

This HEPMSG is a new brushless self-excited and self-regulated generator, which is suitable for an independent power source.

Unlike the existing hybrid excitation permanent magnet machine, this HEPMSG utilized the inherent tooth harmonic EMF of the rotor to adjust the air-gap magnetic field of the permanent magnet machine.

The paper aims to present the hybrid excited claw pole generator design, simulation and experimental results. The prototype has claw poles on two rotor sections, between which an excitation coil is located. The innovation of this machine is permanent magnets location on claws of one part of the rotor. The paper presents construction of the machine and analysis of the current in the excitation control coil influence on the electromagnetic torque, cogging torque and back-emf values. Presented studies enabled the determination of the torque and the back-emf for both: the strengthening and the weakening of magnetic field.

In the study, finite element analysis was used to perform simulation research. Then, based on the simulation studies, an experimental model was built. The paper also presents selected experimental results.

Achieved results show that the proposed machine topology allows to eliminate the disadvantages mentioned in paper, i.e. necessary to introduce special areas inside the machine to limit magnetic flux leakage or its complicated construction.

The obtained cogging torque values and back-emf pulsation are still relatively high. In the near future, some of known techniques for reducing these pulsations can be applied, including the use of magnetic wedges, changing shapes of rotor’s poles and/or skewing of permanent magnets.

The proposed solution can be used in wind turbines as a generator.

The paper presents an original design of a new construction of a hybrid-excited claw pole machine and also an excitation current influence on cogging torque and back-emf values.

Recently, considerable attention has been attracted to the development of the new concept motor for EV or HEV. Wider torque and speed controllable operating range and high efficiency under driving area are needed for traction motor. The purpose of this paper is to realize the new concept variable field flux motor with claw pole rotor and brushless robust structure for high-speed range.

In the previous paper, the authors proposed a half-wave rectified brushless variable field flux method with a diode inserted into the field winding. This paper presents a designing for a novel claw pole rotor type motor using the variable field flux method (CP-HVFM). The claw pole type rotor has simple and robust structure for high-speed operation. This paper describes a first prototype design result for CP-HVFM using 3D-FEM. And the authors report the torque and efficiency characteristic results using 3D-FEM.

The authors have studied the designing for CP-HVFM using 3D-FEM. The designed prototype CP-HVFM reached a rated power of 2 kW or more at a rated speed 1,800 rpm under design restrictions of experimental equipment and initial specifications. In addition, the authors found the ratio of the tip and root embrace of the claw pole shape for maximum average torque and minimum torque ripple. Finally, the authors revealed an influence of the armature current on the torque and the efficiency characteristic results for the designed prototype CP-HVFM using 3D-FEM.

The half-wave rectified brushless variable field flux method proved to be effective for the claw pole rotor type motor. And also the authors found the best claw pole shape for torque characteristic. This results are applied to another concept motor for EV or HEV.

Field excited flux switching machines (FEFSM) are preferred over induction and synchronous machines due to the confinement of all excitation sources on the stator leaving a robust rotor. This paper aims to perform coupled electromagnetic thermal analysis and stress analysis for single phase FEFSM as, prolonged high-speed operational time with core and copper losses makes it prone to stress and thermal constraints as temperature rise in machine lead to degraded electromagnetic performance whereas the violation of the principle stress limit may result in mechanical deformation of the rotor.

This paper presents the implementation of coupled electromagnetic-thermal and rotor stress analysis on single-phase FEFSM with non-overlap winding configurations using finite element analysis (FEA) methodology in JMAG V. 18.1. three-dimensional (3D) magnetic loss analysis is performed and extended to 3D thermal analysis to predict temperature distribution on various parts of the machine whereas Stress analysis predicts mechanical stress acting upon edges and faces of the rotor.

Analysis reveals that temperature distribution and rotor stress on the machine is within acceptable limits. A maximum temperature rise of 37.7°C was noticed at armature and field windings, temperature distribution in stator near pole proximity was 35°C whereas no significant change in rotor temperature was noticed. Furthermore, principal stress at the speed of 3,000 rpm and 30,000 rpm was found out to be 0.0305 MPa 3.045 MPa, respectively.

The designed machine will be optimized for improvement of electromagnetic performance followed by hardware implementation and experimental testing in the future.

The model is developed for axial fan applications.

Thermal analysis is not being implemented on FEFSM for axial fan applications which is an important analysis to ensure the electromagnetic performance of the machine.

The paper aims to propose and compare two new structures of a three-phase wound field salient rotor (WFSR) switched-flux motor (SFM) with 24 stator slots and 10 or 14 rotor poles, respectively, for high-speed operation.

The paper outlines the motor general construction and design concept of proposed machines. Flux linkage, average torque, rotor mechanical strength and torque–speed characteristics of both machines were analyzed and compared by two-dimensional finite element analysis (2D-FEA). Deterministic optimization method was adopted to enhance the characteristics of 24Slot-10Pole WFSR SFM.

The paper provides simulation results and discusses how 24Slot-10Pole WFSR SFM structure is superior to the 24Slot-14Pole in the aspects of flux linkage, average torque and power. It further concludes that the optimized design of 24Slot-10P has achieved 58 and 72 per cent higher average torque and power compared to initial design, as well as high average torque and power compared to 24Slot-14P design.

Optimized structure of the 24Slot-10Pole WFSR SFM with non-overlapping windings has been proposed.

This paper aims to propose and establish a set of new benchmark models to investigate and confidently validate the modeling and prediction of total stray-field loss inside magnetic and non-magnetic components under harmonics-direct current (HDC) hybrid excitations. As a new member-set (P21^e) of the testing electromagnetic analysis methods Problem 21 Family, the focus is on efficient analysis methods and accurate material property modeling under complex excitations.

This P21^e-based benchmarking covers the design of new benchmark models with magnetic flux compensation, the establishment of a new benchmark measurement system with HDC hybrid excitation, the formulation of the testing program (such as defined Cases I–V) and the measurement and prediction of material properties under HDC hybrid excitations, to test electromagnetic analysis methods and finite element (FE) computation models and investigate the electromagnetic behavior of typical magnetic and electromagnetic shields in electrical equipment.

The updated Problem 21 Family (V.2021) can now be used to investigate and validate the total power loss and the different shielding performance of magnetic and electromagnetic shields under various HDC hybrid excitations, including the different spatial distributions of the same excitation parameters. The new member-set (P21^e) with magnetic flux compensation can experimentally determine the total power loss inside the load-component, which helps to validate the numerical modeling and simulation with confidence. The additional iron loss inside the laminated sheets caused by the magnetic flux normal to the laminations must be correctly modeled and predicted during the design and analysis. It is also observed that the magnetic properties (B27R090) measured in the rolling and transverse directions with different direct current (DC) biasing magnetic field are quite different from each other.

The future benchmarking target is to study the effects of stronger HDC hybrid excitations on the internal loss behavior and the microstructure of magnetic load components.

This paper proposes a new extension of Problem 21 Family (1993–2021) with the upgraded excitation, involving multi-harmonics and DC bias. The alternating current (AC) and DC excitation can be applied at the two sides of the model’s load-component to avoid the adverse impact on the AC and DC power supply and investigate the effect of different AC and DC hybrid patterns on the total loss inside the load-component. The overall effectiveness of numerical modeling and simulation is highlighted and achieved via combining the efficient electromagnetic analysis methods and solvers, the reliable material property modeling and prediction under complex excitations and the precise FE computation model using partition processing. The outcome of this project will be beneficial to large-scale and high-performance numerical modeling.

The purpose of this paper is to investigate the use of hybrid‐excitation solutions, using contemporaneously permanent magnets and field coils, for DC machines intended to operate as the core of high‐reliability drives in critical applications supplied by batteries (e.g. fire‐extinguishing pumps, smoke blowers, etc.) where a roughly constant speed is required and a minimal use of electronic devices is prescribed to improve overall dependability.

A high‐reliability hybrid‐excitation DC motor, initially designed basing on theoretical considerations, is then analyzed using purposely developed 2D and 3D finite element method (FEM) electromagnetic models under static, dynamic, healthy, and faulty conditions.

The simulation results confirm that properly designed drives employing hybrid‐excitation DC motors may constitute an effective solution for applications requiring a very high reliability under DC supply with limited speed regulation capability.

The methodology employed exhibits the usual limits concerning the accuracy of FEM analysis: hysteresis is neglected, 2D simulations neglect axial component of fields, in 2D dynamic analysis the electrically discontinuous laminated cores are modeled as orthotropic continuous parts, commutator operation is approximated by means of a position‐dependent resistors network, and the excitation current provided by choppers is approximately considered as constant.

Hybrid excitation DC motors, which may be easily manufactured using existing facilities and mature technologies, might provide an interesting solution for emergency drives requiring minimal regulation capabilities and very high reliability under direct DC supply.

Hybrid excitation is not much investigated in the literature especially for DC motors, although such solution may result potentially interesting especially when a limited flux adjustment capability is required.

In order to keep the advantages of PM generators and eliminate its disadvantage – difficulty in regulating the magnetic field, hybrid excitation is an effective way. The purpose of this paper is to propose a novel way to achieve hybrid excitation by use of tooth harmonic field.

Unlike weakening the tooth harmonics field and EMF in traditional machines, in this paper the tooth harmonics field is proposed to form a novel hybrid excitation permanent magnet synchronous generator (HEPMSG).

The generation mechanism of tooth harmonic electromotive force (EMF) of rotor winding is introduced, and its influencing factors are discussed in detail. The matching design of tooth harmonic winding and field winding for maximum output field current of tooth harmonic excitation system is analyzed.

This machine can achieve not only effective adjustment of the air-gap magnetic field, but also elimination of the brushes and slip rings.

Unlike weakening the tooth harmonics field and EMF in traditional machines, in this paper the tooth harmonics filed is proposed to form a novel hybrid excitation PM synchronous generator. This machine can achieve not only effective adjustment of the air-gap magnetic field, but also elimination of the brushes and slip rings.

The purpose of this paper is to present an analytical modeling based on lumped parameter magnetic circuits of a hybrid excitation synchronous machine. The model is first established and compared with 3D finite elements analysis and measurements. It is then used to optimise hybrid excitation effectiveness.

The machine studied, which has a 3D structure, requires the use of 3D finite elements method. The 3D FEA tool is still time‐consuming, which limits its use in optimal design process. To overcome this limitation the paper investigates an analytical modeling based on lumped parameter magnetic circuits. The developed model is then used in an optimisation procedure.

The machine presented has an original structure. It has been subject to a patent protection. The operating principle of this structure has been presented and optimisation of hybrid excitation effectiveness has been investigated. Double excitation allows one to control air gap flux while reducing permanent magnets' demagnetisation risk.

The paper presents an original structure with true field regulation capability. The principle of operation has been presented. A prototype has been built and tested. The paper also presents a 3D finite elements analysis of this machine and an analytical modelling.

The purpose of this paper is to investigate the generating capability of a novel hybrid excited brushless claw pole alternator (HEBCPA) with improved cost-effectiveness gained thanks to the substitution the rotor NdFeB-made permanent magnet (PM) with ferrite ones.

The investigation of the magnetic features of the novel HEBCPA has been carried out using a 3D finite element analysis (FEA).

It has been found that the machine generating capability is not affected by the substitution of the single rotor NdFeB-made PM by stator and rotor ferrite-made ones, which represents a crucial cost benefit.

An experimental validation of the features computed by FEA shall be considered as an outlook of the present work.

The novel HEBCPA could be of great interest for automotive generating systems.

The proposed HEBCPA with ferrite-made PMs is a novel concept.