Search results

The aim of this paper is to provide a simple yet accurate and efficient geometric method for thermal homogenization of impregnated and non-impregnated coil winding technologies based on the concept of thermal resistance.

For regular windings, the periodic microscopic cell in the winding space is identified. Also, for irregular windings, the average microscopic cell of the winding is determined. An approximation is used to calculate the thermal resistance of the winding cell. Based on this approximation, the winding insulation is considered as a circular ring around the wire. Mathematical equations are obtained to calculate the equivalent thermal resistance of the cell. The equivalent thermal conductivity of the winding is calculated using equivalent thermal resistance of the cell. Winding thermal homogenization is completed by determining the equivalent thermal properties of the cell.

The thermal pattern of different windings is simulated and compared with the results of different homogenization methods. The results show that the proposed method is applicable for a wide range of windings in terms of winding scheme, packing factor and winding insulation. Also, the results show that the proposed method is more accurate than other winding homogenization methods in calculating the equivalent thermal conductivity of the winding.

In this paper, the change of electrical resistance of the winding with temperature and thermal contact between the sub-components are ignored. Also, liquid insulators, such as oils, and rectangular wires were not investigated. Research in these topics is considered as future work.

Unlike other homogenization methods, the proposed method can be applied to non-impregnated and irregular windings. Also, compared to other homogenization methods, the proposed method has a simpler formulation that makes it easier to program and implement. All of these indicate the efficiency of the proposed method in the thermal analysis of the winding.

This paper aims to assess the feasibility of additively manufactured wind tunnel models. The additively manufactured model was used to validate a computational framework allowing the evaluation of the performance of five wing models.

An optimized fighter wing was additively manufactured and tested in a low-speed wind tunnel to obtain the aerodynamic coefficients and deflections at different speeds and angles of attack. The flexible wing model with optimized curvilinear spars and ribs was used to validate a finite element framework that was used to study the aeroelastic performance of five wing models. As a computationally efficient optimization method, homogenization-based topology optimization was used to generate four different lattice internal structures for the wing in this study. The efficiency of the spline-based optimization used for the spar-rib model and the lattice-based optimization used for the other four wings were compared.

The aerodynamic loads and displacements obtained experimentally and computationally were in good agreement, proving that additive manufacture can be used to create complex accurate models. The study also shows the efficiency of the homogenization-based topology optimization framework in generating designs with superior stiffness.

To the best of the authors’ knowledge, this is the first time a wing model with curvilinear spars and ribs was additively manufactured as a single piece and tested in a wind tunnel. This research also demonstrates the efficiency of homogenization-based topology optimization in generating enhanced models of different complexity.

This paper aims to introduce an alternative for modeling levitation forces between NdFeB magnets and bulks of high-temperature superconductors (HTS). The presented approach should be evaluated through two different formulations and compared with experimental results.

The T-A and H-ϕ formulations are among the most efficient approaches for modeling superconducting materials. COMSOL Multiphysics was used to apply them to magnetic levitation models and predict the forces involved.The permanent magnet movement is modeled by combining moving meshes and magnetic field identity pairs in both 2D and 3D studies.

It is shown that it is possible to use the homogenization technique for the T-A formulation in 3D models combined with mixed formulation boundaries and moving meshes to simulate the whole device’s geometry.

The case studies are limited to the formulations’ implementation and a brief assessment regarding degrees of freedom. The intent is to make the simulation straightforward rather than establish a benchmark.

The H-ϕ formulation considers the HTS bulk domain as isotropic, whereas the T-A formulation homogenization approach treats it as anisotropic. The originality of the paper lies in contrasting these different modeling approaches while incorporating the external magnetic field movement by means of the Lagrangian–Eulerian method.

To prevent the coil from burning or getting damaged, it is necessary to estimate the duration of its operation as long as its temperature does not exceed the permissible limit. This paper aims to investigate the effect of switching on the thermal behavior of impregnated and nonimpregnated windings. Also, the safe operating time for each winding is determined.

The power loss of the winding is expressed as a function of the winding specifications. Using homogenization techniques, the equivalent thermal properties for the homogenized winding are calculated and used in a proposed thermal equivalent circuit for winding modeling and analysis. The validity and accuracy of the proposed model are determined by comparing its analysis results and simulation and measurement results.

The results show that copper windings have better thermal behavior and lower temperature compared to aluminum windings. On the other hand, by impregnating or increasing the packing factor of the winding, the thermal behavior is improved. Also, by choosing the right duty cycle for the winding current source, it is possible to prevent the burning or damage of the winding and increase its lifespan. Comparing the measurement results with the analysis results shows that the proposed equivalent circuit has an error of less than 4% in the calculation of the winding center temperature.

In this paper, the effect of temperature on the electrical resistance of the coil is ignored. Also, rectangular wires were not investigated. Research in these topics are considered as future work.

By calculating the thermal time constant of the winding, its safe operation time can be calculated so that its temperature does not exceed the tolerable value (150 °C). The proposed method analyzes both impregnated and nonimpregnated windings with various schemes. It investigates the effects of switching on their thermal behavior. Additionally, it determines the safe operating time for each type of winding.

Intumescent coatings are nowadays a dominant passive system used to protect structural materials in case of fire. Due to their reactive swelling behaviour, intumescent coatings are particularly complex materials to be modelled and predicted, which can be extremely useful especially for performance-based fire safety designs. In addition, many parameters influence their performance, and this challenges the definition and quantification of their material properties. Several approaches and models of various complexities are proposed in the literature, and they are reviewed and analysed in a critical literature review.

Analytical, finite-difference and finite-element methods for modelling intumescent coatings are compared, followed by the definition and quantification of the main physical, thermal, and optical properties of intumescent coatings: swelled thickness, thermal conductivity and resistance, density, specific heat capacity, and emissivity/absorptivity.

The study highlights the scarce consideration of key influencing factors on the material properties, and the tendency to simplify the problem into effective thermo-physical properties, such as effective thermal conductivity. As a conclusion, the literature review underlines the lack of homogenisation of modelling approaches and material properties, as well as the need for a universal modelling method that can generally simulate the performance of intumescent coatings, combine the large amount of published experimental data, and reliably produce fire-safe performance-based designs.

Due to their limited applicability, high complexity and little comparability, the presented literature review does not focus on analysing and comparing different multi-component models, constituted of many model-specific input parameters. On the contrary, the presented literature review compares various approaches, models and thermo-physical properties which primarily focusses on solving the heat transfer problem through swelling intumescent systems.

The presented literature review analyses and discusses the various modelling approaches to describe and predict the behaviour of swelling intumescent coatings as fire protection for structural materials. Due to the vast variety of available commercial products and potential testing conditions, these data are rarely compared and combined to achieve an overall understanding on the response of intumescent coatings as fire protection measure. The study highlights the lack of information and homogenisation of various modelling approaches, and it underlines the research needs about several aspects related to the intumescent coating behaviour modelling, also providing some useful suggestions for future studies.

Laser powder bed fusion (LPBF) in-situ alloying is a recently developed technology that provides a facile approach to optimizing the microstructural and compositional characteristics of the components for high performance goals. However, the complex mass and heat transfer behavior of the molten pool results in an inhomogeneous composition distribution within the samples fabricated by LPBF in-situ alloying. The study aims to investigate the heat and mass transfer behavior of an in-situ alloyed molten pool by developing a three-dimensional transient thermal-flow model that couples the metallurgical behavior of the alloy, thereby revealing the formation mechanism of composition inhomogeneity.

A multispecies multiphase computational fluid dynamic model was developed with thermodynamic factors derived from the phase diagram of the selected alloy system. The characteristics of the Al/Cu powder bed in-situ alloying process were investigated as a benchmark. The metallurgical behaviors including powder melting, thermal-flow, element transfer and solidification were investigated.

The Peclet number indicates that the mass transfer in the molten pool is dominated by convection. The large variation in material properties and temperature results in the presence of partially melted Cu-powder and pre-solidified particles in the molten pool, which further hinder the convection mixing. The study of simulation and experiment indicates that optimizing the laser energy input is beneficial for element homogenization. The effective time and driving force of the convection stirring can be improved by increasing the volume energy density.

This study provides an in-depth understanding of the formation mechanism of composition inhomogeneity in alloy fabricated by LPBF in-situ alloying.

Weak repeatability is observed in handcrafted keypoints, leading to tracking failures in visual simultaneous localization and mapping (SLAM) systems under challenging scenarios such as illumination change, rapid rotation and large angle of view variation. In contrast, learning-based keypoints exhibit higher repetition but entail considerable computational costs. This paper proposes an innovative algorithm for keypoint extraction, aiming to strike an equilibrium between precision and efficiency. This paper aims to attain accurate, robust and versatile visual localization in scenes of formidable complexity.

SiLK-SLAM initially refines the cutting-edge learning-based extractor, SiLK, and introduces an innovative postprocessing algorithm for keypoint homogenization and operational efficiency. Furthermore, SiLK-SLAM devises a reliable relocalization strategy called PCPnP, leveraging progressive and consistent sampling, thereby bolstering its robustness.

Empirical evaluations conducted on TUM, KITTI and EuRoC data sets substantiate SiLK-SLAM’s superior localization accuracy compared to ORB-SLAM3 and other methods. Compared to ORB-SLAM3, SiLK-SLAM demonstrates an enhancement in localization accuracy even by 70.99%, 87.20% and 85.27% across the three data sets. The relocalization experiments demonstrate SiLK-SLAM’s capability in producing precise and repeatable keypoints, showcasing its robustness in challenging environments.

The SiLK-SLAM achieves exceedingly elevated localization accuracy and resilience in formidable scenarios, holding paramount importance in enhancing the autonomy of robots navigating intricate environments. Code is available at https://github.com/Pepper-FlavoredChewingGum/SiLK-SLAM.

The purpose of this study is to examine both the responses of auditees to corporate governance audit (CGA) regulation and the practices of CGA auditors.

The study used a mixed method. Content analysis of 200 annual and CGA reports was carried out for 13 years, from 2008 to 2021, split into voluntary disclosure and mandatory disclosure periods. Quantitative analysis was also conducted using Kruskal–Wallis and Dunn's tests. Data gathered were interpreted through the lens of isomorphism and Oliver's (1991) strategic responses to institutional processes.

The study revealed that in the voluntary disclosure period, auditees responded mainly with acquiescence, motivated by mimetic isomorphic pressure. In the mandatory disclosure period, auditee responses ranged from acquiescence to dismissal of corporate governance regulation (i.e. coercive isomorphic pressure). Auditor reporting of CGA findings was found to be heterogeneous, suggesting that normative and mimetic isomorphism did not homogenize auditor practices.

The absence of uniform auditee responses to CGA regulation during the mandatory disclosure period suggests that the purpose of mandating the regulation has not yet been achieved and may signal inadequate coercive isomorphic pressure from the Financial Reporting Council of Nigeria (FRCN). Similarly, heterogeneous reporting of CGA findings by corporate governance auditors inhibits the comparability of audit findings, limiting their value for information users.

This study examines corporate governance auditor practices and auditee responses to corporate governance audit regulation.

The purpose of this paper is to better understand consumer's familiarity with fruit processing as well as how fruit production conditions (organic and conventional farming), processing conditions (homemade, artisanal and industrial) and the type of processing (e.g. applesauce, apple cider and apple sorbet) influence consumer perceptions of processed fruits.

An online survey questionnaire was applied to 1,000 people living in France. The people represented different genders, ages (18–60+) and sociodemographic categories. Participants were categorized based on their produce purchasing habits (conventional, local, organic, local-organic). The questionnaire contained multiple choice and five point Likert scale questions. Data were analyzed using non-parametric tests.

The authors found that participants saw year-round availability, fruit preservation and food waste reduction as processing advantages. Locally sourced products were preferred to organic products. The perceived disadvantages to processing were additive usage, nutrient loss and packaging. For consumers, these disadvantages drove highly differentiated perceptions of industrial versus artisanal/homemade apple products. Processing conditions appeared to matter far more than production conditions (organic vs. conventional). In general, consumers weren't familiar with processing operations, awareness was greater for consumers of local and/or organic produce than conventional consumers.

There must be a societal transition toward healthier diets, and food technologies. Informed consumers, might be better equipped to make healthy, informed choices if the consumers are given quality information about food production and processing at different levels.

Research has shown that consumers view fresh organic fruit positively, but only few studies have looked at perceptions of processed fruit products and their familiarity with processing operations. Results of this study demonstrate that consumers could make better choices if the consumers are given quality information about fruit production and processing.

An excessive increase in temperature will reduce the lifespan and even burn the coil. The variety of materials in the structure of the electromagnet along with its multi-layer winding creates a complex and heterogeneous thermal structure. There are very few researches that are completely focused on the thermal analysis of electromagnets. The purpose of this paper is to provide an accurate, yet fast and simple method for the thermal analysis of cylindrical electromagnets in both transient and steady-state modes. For this purpose, a thermal equivalent circuit (TEC) is presented based on the nodding approach.

The results of TEC analysis of cylindrical electromagnet, for two orthogonal and orthocyclic winding coil technologies, were compared with the results of the thermal simulation in COMSOL. The authors also built a laboratory model of the cylindrical electromagnet, similar to those analyzed and simulated, and measured the temperature in different parts of it.

The comparison of the results obtained from different methods for the thermal analysis of the cylindrical electromagnet indicates that the proposed TEC has an error of less than 2%. The simplicity and high accuracy of the results are the most important advantages of the proposed TEC.

Comparing the information and results related to winding schemes, indicates that the orthogonal winding has less cost and weight due to the shorter length of the wire used. On the other hand, orthocyclic winding generates lower temperature and has more lifting force, and is simpler to implement. Therefore, in practice, orthocyclic winding technology is usually used.