Search results

The severe friction and wear of the spindle in a cotton picker often occur in a picking cotton, which affects the spindle lifetime and its efficiency of picking cottons. This paper aims to investigate the effect of an electroless nick coating on the spindle performances to avoid its abnormal phenomena.

First, it is coated on the surface of the test specimen with the material same as that of the spindle. Then, the friction coefficient and wear for the coating are measured under oil lubrication to evaluate its effect in improving the tribological performances for the spindle.

The stabilized friction coefficient of the electroless nick coating decreases with increasing reciprocating frequency of specimen and increasing applied load. There exists a critical coating thickness yielding the smallest friction coefficient. Moreover, this coating has a property of the smaller friction coefficient in comparison with a hard chromium coating.

The research about the electroless nick effect on the spindle’s tribological performances is not found yet to date. To avoid severe friction and wear of the spindle, this paper investigated how the reciprocating frequency of specimen, applied load and coating thickness affect the spindle’s tribological performances. The associated conclusions can provide a reference to enhance the spindle lifetime and its transmission efficiency.

Coatings are widely used in gears to keep interface from wearing excessively. The purpose of this paper is to study the effect of coating properties and working conditions on the pressure, the shear traction, stresses as well as the fatigue life of spur gear.

A numerical contact fatigue life model of a coated spur gear pair under elastohydrodynamic lubrication (EHL) is developed based on the characteristics of gear geometry and kinematics, lubrication conditions and material properties. Frequency response functions and the discrete convolute and fast Fourier transform (DC-FFT) algorithm are applied to obtain elastic deformation and stress. Mutil-axial fatigue criteria are used to evaluate the contact fatigue life based upon the predicted time-varying stress fields of coated bodies.

The maximum Mises stress decreases while the fatigue life increases as the coating modulus decreases. A thinner coating leads to a longer life and a smaller maximum Mises stress for hard coatings. The load has more significant effect on the contact fatigue life of soft coatings.

The developed model can be used to evaluate the contact fatigue life of coated gear under EHL and help designers analyze the effect of coating elastic modulus and thickness on the contact pressure, film thickness and stress.

This paper aims to investigate the effects of deposition time on the structure and anti-corrosion properties of a micro-arc oxidation (MAO)/Al coating on AZ31B Mg alloy.

The study describes the fabrication of the coating via a combined process of MAO with multi-arc ion plating. The structure, composition and corrosion resistance of the coatings were evaluated using scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and electrochemical methods.

The Al-layer is tightly deposited with a good mechanical interlock along the rough interface due to the Al diffusion. However, the Al layer reduces the anti-corrosion of MAO-coated Mg alloy because of structural defects such as droplets and cavities, which act as channels for corrosive media infiltration towards the substrate. Fortunately, the Al layer improves the substrate corrosion resistance owing to its passive behaviour, and the corrosion resistance can be enhanced with increasing deposition time. All results indicate that a buffer layer fabricated through the duplex process improves the interfacial compatibility between the hard coating and soft Mg alloys.

An MAO/Al duplex coating was fabricated via a combined process of MAO and physical vapour deposition. MAO/Al duplex coatings exhibit obviously passive behaviours on AZ31 Mg alloy. The structure and corrosion resistance of MAO/Al coatings were investigated.

This paper seeks to summarise the results of available research on the use of high velocity oxy‐fuel (HVOF) thermal‐spray technique to provide protection against high temperature corrosion and erosion‐corrosion of materials.

This paper describes one of the recent thermal‐spray processes, namely HVOF thermal‐spray technology and presents a survey of the studies on the use of this technique to provide protection against corrosion and erosion‐corrosion of high temperature alloys, with a special emphasis on boiler steels.

High temperature corrosion and erosion‐corrosion are serious problems observed in steam‐powered electricity generation plants, gas turbines, internal combustion engines, fluidized bed combustors, industrial waste incinerators and recovery boilers in paper and pulp industries. These problems can be prevented by changing the material or altering the environment, or by separating the component surface from the environment. Corrosion prevention by the use of coatings for separating materials from the environment is gaining importance in surface engineering. Amongst various surface modifying techniques, thermal spraying has developed relatively rapidly due to the use of advanced coating formulations and improvements in coating application technology. One of the variants of thermal spraying, namely HVOF has gained popularity in recent times due to its flexibility for in‐situ applications and superior coating properties.

This review covers mainly information that has been reported previously in the open literature, international journals and some well‐known textbooks.

The paper presents a concise summary of information for scientists and academics, planning to start their research work in the area of surface engineering.

This paper fulfils an identified information/resources need and offers practical help to an individual starting out on a career in the area of surface engineering for erosion‐corrosion and wear.

This paper aims to analyse the influence of the thickness of different layers [diamond-like-carbon (DLC) and chromium nitride (CrN)] on the sliding wear behaviour of a multifunctional coating on AISI 1020 substrates. When small and cheap components need to be manufactured in large scale, they are often produced using soft metals, such as unhardened low carbon steels and pure iron.

Two families, one with thicker films and the other with thinner films, were deposited onto a soft carbon steel substrate by plasma-enhanced chemical vapour deposition (PECVD). Reciprocating linear tests with incremental loading assessed the durability of the coatings. In addition, friction coefficient and wear rates of both specimens and counterbodies were measured at a constant load.

Thinner layers presented lower sliding wear rates (four-five times lower) for both specimens and counterbodies, less spalling and protective tribolayers on the wear tracks.

Although multilayered CrN–DLC coatings on relatively hard substrates such as HSS and cemented carbide tools are already a proven technology, much less is known about its deposition on a much softer substrate such as low carbon steel. In previous works, we have analysed the influence of layer thickness on hardness and scratch resistance of the same coatings. This paper presents results for their performance under wear sliding conditions using an original approach (three-dimensional triboscopic maps) for two distinct configurations (increasing load and constant load).

The purpose of this paper is to examine mechanical and metallurgical properties of AlTiN- and TiN-coates high-speed steel (HSS) materials in detail.

In this study, HSS steel parts have been processed through machining and have been coated with AlTiN and TiN on physical vapour deposition workbench at approximately 6,500°C for 4 hours. Tensile strength, fatigue strength, hardness tests for AlTiN- and TiN-coated HSS samples have been performed; moreover, energy dispersive X-ray spectroscopy and X-ray diffraction analysis and microstructure analysis have been made by scanning electron microscopy. The obtained results have been compared with uncoated HSS components.

It was found that tensile strength of TiAlN- and TiN-coated HSS parts is higher than that of uncoated HSS parts. Highest tensile strength has been obtained from TiN-coated HSS parts. Number of cycles for failure of TiAlN- and TiN-coated HSS parts is higher than that for HSS parts. Particularly TiN-coated HSS parts have the most valuable fatigue results. However, surface roughness of fatigue samples may cause notch effect. For this reason, surface roughness of coated HSS parts is compared with that of uncoated ones. While the average surface roughness (Ra) of the uncoated samples was in the range of 0.40 μm, that of the AlTiN- and TiN-coated samples was in the range of 0.60 and 0.80 μm, respectively.

It would be interesting to search different coatings for cutting tools. It could be the good idea for future work to concentrate on wear properties of tool materials.

The detailed mechanical and metallurgical results can be used to assess the AlTiN and TiN coating applications in HSS materials.

This paper provides information on mechanical and metallurgical behaviour of AlTiN- and TiN-coated HSS materials and offers practical help for researchers and scientists working in the coating area.

The effect of cryogenic heat treatment on the mechanical properties of different materials has been frequently investigated by researchers in recent years. The purpose of this paper is to investigate wear behaviour of monolayer, multilayer and nanocomposite coatings after cryogenic heat treatment. It is a first in its field in terms of both the heat treatment used and the coatings examined.

The aCN/TiAlN, TiAlN and ncTiAlSiN hard coatings deposited on the AISI D2 steel substrate were subjected to cryogenic heat treatment at −145^oC and −196^oC for 24 h and then tempered at 200^oC for 2 h. Then, the samples were subjected to wear tests of 5, 10 and 15 N three different load values. The wear mechanisms occurring on the wear surfaces were determined by scanning electron microscope supported by EDS.

Oxidation, fatigue and delamination wear mechanisms were realized on the surfaces of the samples subjected to dry sliding wear test. The wear resistance of S1 increased with cryogenic heat treatment. According to the wear test results of the untreated samples, it was found that the samples with lower hardness than the others had higher wear resistance. The wear resistance of S1 and S2 samples was increased by cryogenic heat treatment. The best wear resistance in all parameters was obtained by S1. Oxidation in the S1 was found to have a positive effect on wear resistance. According to EDS results after wear of S2, chromium-rich layer was found on the surface of the material. It is understood that cryogenic heat treatment causes carbide precipitation in the inner structure of the substrate material.

The effect of cryogenic heat treatment on the mechanical properties of different materials has been frequently investigated by researchers in recent years. In this study, wear behaviour of monolayer, multilayer and nanocomposite coatings after cryogenic heat treatment was investigated. It is a first in its field in terms of both the heat treatment used and the coatings examined.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2020-0111/

The purpose of this paper is to examine mechanical and metallurgical properties of AlTiN coating HSS materials in detail.

In this study, high-speed steel (HSS) parts were processed by the way of machining and were coated with AlTiN on physical vapour deposition (PVD) workbench at approximately 650°C for 4 h. Tensile strength, fatigue strength and hardness tests for AlTiN coated HSS samples were performed. Samples were also analyzed by energy dispersive X-ray analysis (EDS), X-ray diffraction (XRD) and scanning electron microscope (SEM). The results were compared with uncoated HSS components.

It was found that an amorphous aluminium-oxide layer emerges on surface of parts by AlTiN coating. This layer prevents further oxide formations. The coating thickness of AlTiN-coated sample is between 1,530 and 1,558 μm. Compared to uncoated HSS, AlTiN coated HSS gives higher performance.

It would be interesting to search different coatings for cutting tools. It could be the good idea for future work concentrated wear properties on tool materials using different coatings.

This paper provides information on mechanical and metallurgical behaviour of AlTiN coated HSS materials and offers practical help for the researchers and scientists working in the coating area.

The Kanigen process of nickel deposition by catalytic chemical reduction is a practical production method for uniformly coating metals and non‐metals with a layer of hard, corrosion‐resistant amorphous nickel‐phosphorus alloy. This process has made available to industry a material with new and considerably improved surface properties. Both the technique and the product are unique. The amorphous high‐nickel low‐phosphorus alloy is deposited at a uniform rate on the piece being coated wherever it is in contact with the hot solution and whatever the shape. The non‐porous coating is hard but relatively brittle, adheres well to most properly pretreated basis materials, and has improved corrosion resistance (compared to pure nickel) which can be increased further by heat treatment.

The purpose of this study was to develop a TiAlSiCN coating with high bonding and hardness, ultra-low friction and good lubrication characteristics, which provided an experimental basis for the surface modification of YT14 cemented carbide cutting tools.

In this work, a TiAlSiCN coating was deposited on YT14 cemented carbide cutting tool through cathodic arc ion plating. The surface-interface morphologies, distributions of chemical elements, phases, bonding energy and surface roughness were analyzed using field emission scanning electron microscopy, energy-dispersive spectroscopy (EDS), X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy, respectively, and the coating the bonding strength were quantitatively characterized with a scratch.

The average COFs of the TiAlSiCN coating at 700°C, 800°C and 900°C were 0.68, 0.57 and 0.38, respectively, showing that the TiAlSiCN coating was an effective lubricant at a high temperature, and the wear rate of the coating increases with wear temperature. After wearing at 700°C, 800°C and 900°C, the Ti, Si and N elements form atom-poor regions, while Al forms an atom-rich region, showing that the oxides of Ti, Al and Si are formed to improve the wear resistance of the coating. The wear mechanism of TiAlSiCN coating at high temperatures was composed of abrasive wear and oxidation wear.

The friction-wear behaviors of TiAlSiN coating were investigated using an HT-1000-type high-temperature friction wear tester, and the worn tracks on the coatings were analyzed using an EDS plane scan, thus obtaining the wear mechanism of TiAlSiN coating.