Search results

This paper intends to demonstrate the feasibility of thick film piezoelectric layers on ceramic substrates. Advantages of this technology for the realisation and improvement of some devices, such as loudspeakers and couplers (to be applied in a communication bus), are described.

Water cooling of hybrid modules allows a power dissipation much higher than that of conventional methods. This paper describes the design and construction of a copper‐clad Invar water‐cooled hybrid power circuit intended for use in a medical hand‐held tool which is a 25 mm diameter cylinder. The thermal study demonstrates the interest of a copper‐clad Invar heat exchanger: water flowing at a rate lower than 15 Ih−1 allows the dissipation of more than 50 W in the module while keeping the external temperature of the tool below 35°C.

A month or so after the Stresa meeting, the French ISHM chapter, organising a session on ‘Gallic inks’ (!), summoned me to deliver some comments on the 5th European Hybrid Microelectronics Conference. Although it was only a matter of interlude during this technical session, I felt the task quite a difficult one. It became a hazardous project when Brian C. Waterfield kindly asked me to let what is in fact a personal opinion—my personal opinion, standing back from my daily work—appear in Hybrid Circuits. I'll do my best.

The powder and rheology properties of a gold and a silver thick film ink are associated with its fine line performance. Printing 100 micron lines is shown to be straightforward and 75 microns is speculated as being feasible.

Transport shapes the health of urban populations. It can support healthy behaviours such as participation in regular physical activity and access to community connection. Transport systems can also have major negative impacts on health. For example, through air pollution from fossil fuel-based modes of travel, the risk of injury and death from transport related collisions, and in the way sedentary modes of travelling can contribute to less physically active lifestyles.

This chapter considers the long-term impact of the pandemic on a series of well-researched transport-related health outcomes. It first describes the established connections between transport and health. It then considers the future implications of three potential pandemic-induced shifts: the increased uptake of working from home (WFH); decreased usage of public transport and increased interest in walking and cycling in the local neighbourhood. The impacts of these shifts on the transport-health nexus are then discussed, revealing both positive and negative outcomes. The authors conclude by providing policy recommendations to mitigate possible negative outcomes and strengthen the positive consequences into the future.

ISHM (UK) presented a technical meeting on this topic on the 23rd October 1982 at the Cunard International Hotel, London. The meeting was attended by some 50 engineers, both those involved in the field of hybrids and potential users. It was generally felt that this was a useful meeting but more especially that it would have appealed to many potential users of hybrids, had the right people been able to be contacted.

A new type of realisation of the hydrotalcite‐type lamellar compound Zn2AI(OH)6Cl.nH2O is described, using an original ink composed of a concentrated aqueous suspension of Zn2AI(OH)6Cl.nH2O powder, which, when applied by the screen‐printing technique, in particular environmental conditions—in a high relative humidity atmosphere—permits one to obtain very satisfactory deposits. Optical characterisation shows good resolution and levelling of the screen‐printed layer. X‐ray patterns show a high orientation of the (hkO) reticular planes of the screen‐printed material in a direction parallel to the substrate; this is a very interesting characteristic related to experiment on the electrical properties of this type of compound. Tests show the good adherence of the deposited layer on alumina or glass. Future applications are envisaged.

This paper outlines methods and results of wetting, leaching and adhesion analyses on copper thick film conductors over alumina and multilayer glasses after different processing conditions. The intention is to provide a better background for evaluating and optimising materials and processing conditions in copper thick films and working out quick, reliable and quantitative methods for better characterisation of copper conductors in production. For these reasons the following methods were used: (a) wetting and leaching analyses with a scanning wetting balance, working in nitrogen, (b) pull tests with solder contacts on copper thick film conductors after soldering, ageing and thermal cycling, and (c) some additional surface analyses (REM, EDX, Auger) for a better understanding of copper pastes and their material interactions, when processed under different conditions. The results are summarised under three general aspects: surface structure and wetting of copper thick films, wetting and leaching of various copper thick films after different processing conditions, and finally the influence of different wetting properties of such surfaces on the solder adhesion strength after soldering, ageing and thermal cycling. The results give good insight into the various interactions of copper thick films with their substrate materials and confirm the ability of the described wetting and leaching analyses for these purposes.

On 20 April ISHM‐Benelux held its 1988 Spring meeting at the Grand Hotel Heerlen. This meeting was totally devoted to implantable devices, in particular to the technologies used for these high reliability, extremely demanding devices. For this meeting ISHM‐Benelux was the guest of the Kerkrade facility of Medtronic. Medtronic (headquartered in Minneapolis, USA) is the world's leading manufacturer of implantable electronic devices. Apart from the assembly of pacemakers and heart‐wires, the Kerkrade facility acts as a manufacturing technology centre for Medtronic's European facilities.

Drive east from Frankfurt, upstream along the valley of the River Main, and in 25 kilometres or so you will reach Hanau, where once the brothers Grimm lived and collected the folklore which we now know as the famous Tales. Here too, in 1856, Wilhelm Carl Heraeus, a chemist and pharmacist, proprietor of the pharmacy which had carried the family name for many generations, succeeded in producing temperatures approaching 2000°C from an oxy‐hydrogen flame, temperatures sufficiently high to achieve the melting point of platinum and to allow him to melt substantial quantities of this metal for the first time. Hanau was then a centre for the jewellery manufacturing industry (and remains so today) so the smelting of platinum and other precious metals had an immediate commercial relevance.