Search results

The grain size and grain distribution mode have a significant impact on the tribological properties of Babbitt alloy. The purpose of this paper is to study the effect of differentiated SnSb grain size distribution on the improvement of tribological properties of Babbitt alloy.

Babbitt (marked by babbitt-cr), with a differentiated SnSb grain size distribution, was fabricated using a selective zone laser surface treatment. Bare Babbitt with coarse SnSb grain was marked as babbitt-c, and Babbitt with refined SnSb grain was marked as babbitt-r. The microstructure, microhardness and wettability of specimens were tested. The tribological properties of babbitt-c, babbitt-r and babbitt-cr were evaluated under dry and lubricated conditions.

The microstructure transforms from single coarse SnSb grain distribution or single refined SnSb grain distribution to differentiated SnSb grain size distribution, as a result of selective zone laser surface treatment. Among three specimens of microhardness, babbitt-cr showed the highest microhardness. The lipophilicity property of babbitt-cr was better compared to babbitt-c. A mixture of coarse and refined grain is beneficial to improve the tribological properties of Babbitt alloy under dry condition. Furthermore, compared with babbitt-c, the wear resistance of babbitt-cr was enhanced under lubricated condition. However, the anti-wear property of babbitt-cr was not significantly improved relative to babbitt-r with an increase in the loads.

The study demonstrates that modulated different grain size alternating distribution modes can improve the tribological properties of Babbitt alloy.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-09-2022-0259/

Understanding and tailoring the solidification characteristics and microstructure evolution in as-built parts fabricated by laser powder bed fusion (LPBF) is crucial as they influence the final properties. Experimental approaches to address this issue are time and capital-intensive. This study aims to develop an efficient numerical modeling approach to develop the process–structure (P-S) linkage for LPBF-processed Inconel 718.

In this study, a numerical approach based on the finite element method and cellular automata was used to model the multilayer, multitrack LPBF build for predicting the solidification characteristics (thermal gradient G and solidification rate R) and the average grain size. Validations from published experimental studies were also carried out to ensure the reliability of the proposed numerical approach. Furthermore, microstructure simulations were used to develop P-S linkage by evaluating the effects of key LPBF process parameters on G × R, G/R and average grain size. A solidification or G-R map was also developed to comprehend the P-S linkage.

It was concluded from the developed G-R map that low laser power and high scan speed will result in a finer microstructure due to an increase in G × R, but due to a decrease in G/R, columnar characteristics are also reduced. Moreover, increasing the layer thickness and decreasing the hatch spacing lowers the G × R, raises the G/R and generates a coarse columnar microstructure.

The proposed numerical modeling approach was used to parametrically investigate the effect of LPBF parameters on the resulting microstructure. A G-R map was also developed that enables the tailoring of the as-built LPBF microstructure through solidification characteristics by tuning the process parameters.

The changes in tensile behavior of polycrystalline nanocopper lattice with changes in temperature, average grain size (AGS) and strain rate, have been explored. The existence of a critical AGS has also been observed which shows that the Hall–Petch relationship behaves inversely.

Nanoscale deformation of polycrystalline nanocopper has been done in this study with the help of an embedded atom method (EAM) potential. Voronoi construction method has been employed for creating four polycrystals of nanocopper with different sizes. Statistical analysis has been used to examine the observations with emphasis on the polycrystal size effect on melting point temperature.

The study has found that the key stress values (i.e. elastic modulus, yield stress and ultimate tensile stress) are significantly influenced by the considered parameters. The increase in strain rate is observed to have an increasing impact on mechanical properties, whereas the increase in temperature degrades the mechanical properties. In-depth analysis of the deformation mechanism has been studied to deliver real-time visualization of grain boundary motion.

This study provides the relationship between required grain size variations for consecutive possible variations in mechanical properties and may help to reduce the trial processes in the synthesis of polycrystalline copper based on different temperatures and strain rates.

In recent years, additive manufacturing (AM) has started to be used for manufacturing real functional parts and assemblies for critical applications in aerospace, automotive, and machinery industries. Most complex or assembled parts require internal features (IF) such as holes, channels, slots, or guides for locational and mating requirements. Therefore, it is critical to understand and compare the structural and mechanical properties of additively manufactured and conventionally machined IFs.

In this study, mechanical and microstructural properties of Inconel 718 (Inc718) alloy internal features, manufactured either as-built with AM or machining of additively manufactured (AMed) part thereafter were investigated.

The results showed that the average ultimate tensile strength (UTS) of additively manufactured center internal feature (AM-IF) is almost analogous to the machined internal feature (M-IF). However, the yield strength of M-IF is greater than that of AM-IF due the greater surface roughness of the internal feature in AM-IF, which is deemed to surpass the effect of microstructure on the mechanical performance. The results of digital image correlation (DIC) analysis suggest that AM-IF and M-IF conditions have similar strain values under the same stress levels but the specimens with as built IF have a more locally ductile region around their IF, which is confirmed by hardness test results. But this does not change global elongation behavior. The microstructural evolution starting from as-built (AB) and heat-treated (HT) samples to specimens with IF are examined. The microstructure of HT specimens has bimodal grain structure with d phase while the AB specimens display a very fine dendritic microstructure with the presence of carbides. Although they both have close values, machined specimens have a higher frequency of finer grains based on SEM images.

It was shown that the concurrent creation of the IF during AM can provide a final part with a preserved ultimate tensile strength and elongation but a decreased yield strength. The variation in UTS of AM-IF increases due to the surface roughness near the internal feature as compared to smooth internal surfaces in M-IF. Hence, the outcomes of this study are believed to be valuable for the industry in terms of determining the appropriate production strategy of parts with IF using AM and postprocessing processes.

The purpose of this paper is to determine (1) the relationship between microstructure and fatigue cracking behavior and (2) effect of rolling on the process of crack initiation and propagation in FeCrAl alloys.

The qualitative and quantitative fracture studies were performed using scanning electron microscopy and the non-contact optical measurement system (IFMG5).

The results show that the formation of facets, rough facets and parallel stripes in the crack initiation and early crack propagation zones are closely related to the sensitivity of crack behavior to the microstructure of the material. Besides, the rolling process has a significant influence on the small crack initiation and propagation behavior. Quantitative analysis demonstrates that the size of the stress intensity factor and plastic zone size in the rough zone is associated with the rolling process.

The findings of this study have the potential to enhance the understanding of the microstructural crack formation mechanisms in FeCrAl alloys and shed light on the impact of rolling on the long-term and ultra-long fatigue behavior of these alloys. This new knowledge is vital for improving manufacturing processes and ensuring the safety and reliability of FeCrAl alloys used in nuclear industry applications.

An experimental investigation for developing structure-property correlations of hot-rolled E410 steels with different carbon contents, i.e. 0.04wt.%C and 0.17wt.%C metal active gas (MAG) and cold metal transfer (CMT)-MAG weldments was undertaken.

Mechanical properties and microstructure of MAG and CMT-MAG weldments of two E410 steels with varying content of carbon were compared using standardized mechanical testing procedures, and conventional microscopy.

0.04wt.%C steel had strained ferritic and cementite sub-structures in blocky shape and large dislocation density, while 0.17wt.%C steel consisted of pearlite and polygonal ductile ferrite. This effected yield strength (YS), and microhardness being larger in 0.04wt.%C steel, %elongation being larger in 0.17wt.%C steel. Weldments of both E410 steels obtained with CMT-MAG performed better than MAG in terms of YS, ultimate tensile strength (UTS), %elongation, and toughness. It was due to low heat input of CMT-MAG that resulted in refinement of weld metal, and subzones of heat affected zone (HAZ).

A substantial improvement in YS (∼9%), %elongation (∼38%), and room temperature impact toughness (∼29%) of 0.04wt.%C E410 steel is achieved with CMT-MAG over MAG welding. Almost ∼10, ∼12.5, and ∼16% increment in YS, %elongation, and toughness of 0.17wt.%C E410 steel is observed with CMT-MAG. Relatively low heat input of CMT-MAG leads to development of fine Widmanstätten and acicular ferrite in weld metal and microstructural refinement in HAZ subzones with nearly similar characteristics of base metal.

Additive manufacturing (AM) can achieve significant weight savings with only minor compromises in strength if high-performance wrought aluminum alloys are used as feedstock. Despite the advantages in strength that aluminum alloys (AA) 6061 offer, they cannot be manufactured via printing because of hot cracking and other solidification problems. The purpose of this study is to achieve high-quality printing of AA6061 with nanotreated wires.

Nanotreating was used to modify the AA6061 alloy composition by adding a small fraction of nanoparticles to enhance the alloy’s manufacturability and resultant properties. Wire arc additive manufacturing (WAAM) was used to print the nanotreated AA6061 wire feedstock. The microstructure of the printed AA6061 was characterized by X-ray crystallography, optical microscopy, scanning electron microscopy and energy dispersive spectroscopy mapping. The microhardness profile, tensile behavior and fracture surface were analyzed.

This work successfully used WAAM to print nanotreated AA 6061 components. The resulting AA6061 parts were crack-free, with exceptional grain morphology and superior mechanical properties. Owing to the excellent size control capabilities of nanoparticles, a homogeneous distribution of small grains was maintained in all deposited layers, even during repeated thermal cycles.

Previous studies have not successfully printed AA6061 using WAAM. Conventional WAAM products exhibit anisotropic mechanical properties. The nanotreated AA6061 was successfully printed to achieve homogeneous microhardness and isotropic tensile properties. The promising results of this study reflect the great potential of nanotech metallurgy as applied to the WAAM process.

The purpose of this paper is to determine the ultra-high cycle fatigue behavior and ultra-slow crack propagation behavior of selective laser melting (SLM) AlSi7Mg alloy under as-built conditions.

Constant amplitude and two-step variable amplitude fatigue tests were carried out using ultrasonic fatigue equipment. The fracture surface of the failure specimen was quantitatively analyzed by scanning electron microscope (SEM).

The results show that the competition of surface and interior crack initiation modes leads to a duplex S–N curve. Both manufacturing defects (such as the lack of fusion) and inclusions can act as initially fatal fatigue microcracks, and the fatigue sensitivity level decreases with the location, size and type of the maximum defects.

The research results play a certain role in understanding the ultra-high cycle fatigue behavior of additive manufacturing aluminum alloys. It can provide reference for improving the process parameters of SLM technology.

The purpose of this study to investigate the organized porous network zinc (OPNZ) scaffolds. Their mechanical characteristics, surface roughness and fracture mechanism were assessed in relation to their structural properties. The prospects of fused deposition modeling (FDM) for printing metal scaffolds via rapid tooling have also been studied.

Zn scaffolds with different pore and strut sizes were manufactured via the rapid tooling method. This method is a multistep process that begins with the 3D printing of a polymer template. Later, a paraffin template was obtained from the prepared polymer template. Finally, this paraffin template was used to fabricate the Zn scaffold using microwave sintering. The characterization of prepared Zn samples involved structural characterization, microstructural study, surface roughness testing and compression testing. Moreover, based on the Gibson–Ashby model analysis, the model equations’ constant values were evaluated, which can help in predicting the mechanical properties of Zn scaffolds.

The scanning electron microscopy study confirmed that the fabricated sample pores were open and interconnected. The X-ray diffraction analysis revealed that the Zn scaffold contained hexagonal closed-packed Zn peaks related to the a-Zn phase, validating that scaffolds were free from contamination and impurity. The range for ultimate compressive strength, compressive modulus and plateau stresses for Zn samples were found to be 6.75–39 MPa, 0.14–3.51 GPa and 1.85–12.6 MPa by adjusting their porosity, which are comparable with the cancellous bones. The average roughness value for the Zn scaffolds was found to be 1.86 µm.

This research work can widen the scope for extrusion-based FDM printers for fabricating biocompatible and biodegradable metal Zn scaffolds. This study also revealed the effects of scaffold structural properties like porosity, pore and strut size effect on their mechanical characteristics in view of tissue engineering applications.

The purpose of this study is to delve into the mechanism of Si3N4 nanowires (NWs) in Sn-based solder, thereby furnishing a theoretical foundation for the expeditious design and practical implementation of innovative lead-free solder materials in the electronic packaging industry.

This study investigates the effect of adding Si₃N₄ NWs to Sn58Bi solder in various mass fractions (0, 0.1, 0.2, 0.4, 0.6 and 0.8 Wt.%) for modifying the solder and joining the Cu substrate. Meanwhile, the melting characteristics and wettability of solder, as well as the microstructure, interfacial intermetallic compound (IMC) and mechanical properties of joint were evaluated.

The crystal plane spacing and lattice constant of Sn and Bi phase increase slightly. A minor variation in the Sn58Bi solder melting point was caused, while it does not impact its functionality. An appropriate Si₃N₄ NWs content (0.2∼0.4 Wt.%) significantly improves its wettability, and modifies the microstructure and interfacial IMC layer. The shear strength increases by up to 10.74% when adding 0.4 Wt.% Si₃N₄ NWs, and the failure mode observed is brittle fracture mainly. However, excessive Si₃N₄ will cause aggregation at the junction between the solder matrix and IMC layer, this will be detrimental to the joint.

The Si₃N₄ NWs were first used for the modification of lead-free solder materials. The relative properties of composite solder and joints were evaluated from different aspects, and the optimal ratio was obtained.