Search results

Everyone is extremely concerned about environmental protection and health safety due to the rise in living standards. Plant-derived natural dyes have garnered much industrial attention in food, pharmaceutical, textile, cosmetics, etc. owing to their health and environmental benefits. The present study aims to focus on the elimination of the use of synthetic dyes and provides brief information about natural dyes, their sources, extraction procedures with characterization and various advantages and disadvantages.

In producing natural colors, extraction and purification are essential steps. Various conventional methods used till date have a low yield, as these consume a lot of solvent volume, time, labor and energy or may destroy the coloring behavior of the actual molecules. The establishment of proper characterization and certification protocols for natural dyes would improve the yielding of natural dyes and benefit both producers and users.

However, scientists have found modern extraction methods to obtain maximum color yield. They are also modifying the fabric surface to appraise its uptake behavior of color. Various extraction techniques such as solvent, aqueous, enzymatic and fermentation and extraction with microwave or ultrasonic energy, supercritical fluid extraction and alkaline or acid extraction are currently available for these natural dyes and are summarized in the present review article.

If natural dye availability can be increased by the different extraction measures and the cost of purified dyes can be brought down with a proper certification mechanism, there is a wide scope for the adoption of these dyes by small-scale dyeing units.

Agricultural waste and food sources are some of the pollutants of the environment. One of these wastes is the peel of fruits that cannot be consumed as food. In this regard, walnut husk (WH) and oleaster peel (PO) are known as two important sources of tannin and are bulky wastes. Because of the high percentage of tannin, these materials can be used as a natural source for the preparation of bio-mordant in the dyeing process.

In this study, Reseda and Madder were used as natural dyes in the presence of a mixture of two bio-mordants. WH and PO were selected as bio-mordant. All natural resources are extracted to obtain the juice. The phenolic percentage of tannin-containing extracts was evaluated and then it was used for wool yarns by premordanting method. The results of evaluating the fastness properties using the ISO method.

The most important achievement of this research is the use of agricultural waste in the dyeing process to reduce environmental pollution and create added value. All compounds rich in tannin have some phenolic components, therefore the amount of phenolic content of these extracts was evaluated. The effect of mixing the mordant on the color characteristics of the yarns was investigated and the results showed that changing the ratio of the combination of two mordant is effective on the K/S values. The results of evaluating the fastness properties using the ISO method showed that the washing, rubbing and light fastness in the presence of mordant is good, good and moderate, respectively.

In this paper, to the best of the authors’ knowledge, for the first time, the combination of two natural extracts obtained from agricultural waste has been used to create a new bio-mordant on fibers and improve stability.

Due to herbs and plants’ therapeutic properties and simplicity of availability in nature, humans have used them to treat a variety of maladies and diseases since ancient times. Later, as technology advanced, these plants and herbs gained significant relevance in some industries due to their suitable chemical composition, abundant availability and ease of access. Aegle marmelos is a species of plant that may be found in nature. Yet, little or very little literature was located on the coloration behavior of this plant’s leaves. This study aims to focus on the effect of different parameters on the extraction of colorant from Aegle marmelos leaves.

Some factors that affected on the extraction processes were examined and found to have significant impacts on the textile dyeing such as the initial dye concentration, extracted temperature, extracted bath pH and extracted time were all changed to see how they affected color extraction. The authors report a direct comparison between three heating methods, namely, microwave irradiation (MWI), ultrasonic waves (USW) and conventional heating (CH). The two kinetic models have been designed (pseudo-first and pseudo-second orders) in the context of these experiments to investigate the mechanism of the dyeing processes for fabrics under study. Also, the experimental data were analyzed according to the Langmuir and Freundlich isotherms.

From the result, it was discovered these characteristics were found to have a substantial effect on extraction efficiency. Temperature 90°C and 80°C when using CH and USW, respectively, while at 90% watt when using MWI, period 120 min when using CH as well as USW waves, while 40 min when using MWI, and pH 4, 5 and 10 for polyamide, wool and cotton, respectively, were the optimal extraction conditions. Also, the authors can say that wool gives a higher absorption than the other fabric. Additionally, MWI provided the best color strength (K/S) value, and homogeneity, at low temperatures reducing the energy and time consumed. The coloring follows the order: MWI > USW > CH. The adsorption isotherm of wool could be well fitted by Freundlich isotherm when applying CH and USW as a heating source, while it is well fitted by the Langmuir equation in the case of MWI. In the study, it was observed that the pseudo-first-order kinetic model fits better the experimental results of CH with a constant rate K₁ = −0.000171417 mg/g.min, while the pseudo-second-order kinetic model fits better the experimental results of absorption of both MWI (K2 = 38.14022572 mg/g.min) and USW (K₂ = 12.45343554 mg/g.min).

There is no research limitation for this work. Dye was extracted from Aegle marmelos leaves by applying three different heating sources (MWI, ultrasonic waves [USWW] and CH).

This work has practical applications for the textile industry. It is concluded that using Aegle marmelose leaves can be a possible alternative to extract dye from natural resource by applying new technology to save energy and time and can make the process greener.

Socially, it has a good impact on the ecosystem and global community because the extracted dye does not contain any carcinogenic materials.

The work is original and contains value-added products for the textile industry and other confederate fields.

This study aims to synthesize Prussian blue {Fe^III₄[Fe^II(CN)₆]₃} pigment by reacting ferric chloride with different ferrocyanides through the same procedure. The influence of the ferrocyanide used on resulting pigment properties is studied.

Prussian blue is commonly synthesized by direct or indirect methods, through iron salt and ferrocyanide/ferricyanide reactions. In this study, the direct, single-step process was pursued by dropwise addition of the ferrocyanide into ferric chloride (both as aqueous solutions). Two batches – (K-PB) and (Na-PB) – were prepared by using potassium ferrocyanide and sodium ferrocyanide, respectively. The development of pigment was confirmed by an identification test and characterized by spectroscopic techniques. Pigment properties were determined, and light fastness was observed for acrylic emulsion films incorporating dispersed pigment.

The two pigments differed mainly in elemental detection owing to the dissimilar ferrocyanide being used; IR spectroscopy where only (Na-PB) showed peaks indicating water molecules; and bleeding tendency where (K-PB) was water soluble whereas (Na-PB) was not. The pigment exhibited remarkable blue colour and good bleeding resistance in several solvents and showed no fading in 24 h of light exposure though oil absorption values were high.

This article is a comparative study of Prussian blue pigment properties obtained using different ferrocyanides. The dissimilarity in the extent of water solubility will influence potential applications as a colourant in paints and inks. K-PB would be advantageous in aqueous formulations to confer a blue colour without any dispersing aid but unfavourable in systems where other coats are water-based due to their bleeding tendency.

This paper aims to evaluate the effects of banana (Musa) peel and guava (Psidium guajava) leaves extract as mordants on jute–cotton union fabrics dyed with onion skin extract as a natural dye.

The dye was extracted from the outer skin of onions by boiling in water and later concentrated. The bio-mordants were prepared by maceration using methanol and ethanol. The fabrics were pre-mordanted, simultaneously mordanted and post-mordanted with various concentrations according to the weight of the fabric. The dyed and mordanted fabrics were later subjected to measurement of color coordinates, color strength and colorfastness to the washing test. Furthermore, the dyed samples were characterized by Fourier transform infrared, and different chemical bonds were analyzed by X-ray photoelectron spectroscopy analysis.

Significant improvement was obtained in colorfastness and color strength values in various instances using banana peel and guava leaves as bio mordants. Post-mordanted with banana peel provided the best results for wash fastness. Better color strength was achieved by fabric post-mordanted with guava leave extracts.

Sustainable dyeing methods of natural dyes using banana peel and guava leaves as bio mordants were explored on jute–cotton union fabrics. Improvement in colorfastness and color strength for various instances was observed. Thus, this paper provides a promising alternative to metallic salt mordants.

This study aims to investigate the effect of spray drying temperature and maltodextrin addition on the contents of phenolics, flavonoids, anthocyanins and antioxidant activities (2,2-diphenyl-1-picrylhydrazyl [DPPH] radical scavenging activity, ferric reducing antioxidant power and reducing power) of karonda powder.

Over the past few decades, the demands for application of natural colorants in food production have been attracting the attention of academic research and food industry. Anthocyanins, a red pigment commonly found on plants, show high potentials in the preparation of spray-dried pigment powder. This study, therefore, was conducted using full factorial design with two factors, namely, inlet temperature (150°C and 160°C) and soluble solid concentration (10, 15 and 20°Brix) with maltodextrin as carrier to produce pigment powder from karonda, an anthocyanin-rich fruit which is native to southeast Asia.

Increasing soluble solid content from 10 to 15°Brix resulted in a 42%–57% reduction in phenolic, flavonoid and anthocyanin contents. However, when increasing the amount of maltodextrin from 15 to 20°Brix, a lower reduction (approximately 11%–19%) was observed. In samples with the same °Brix, there was no significant variation in antioxidant contents and activities, especially at high maltodextrin ratios. In addition, the reducing power of samples dried at higher temperature (160°C) was higher than that of samples dried at lower temperature. Karonda spray-dried powder showed a good positive correlation (p < 0.01) between antioxidant contents and DPPH• activity.

To the best of the authors’ knowledge, in this study, for the first time, the effect of spray drying conditions on the quality of karonda powder was investigated.

The main purpose of this study was to prepare the cotton fibers and cellulose powder by a layer of nano-crystalline-titanium dioxide (TiO₂) using the sol-gel sono-synthesis method to clean the wastewater containing reactive dye. Moreover, TiO₂ nano-materials are remarkable due to their photoactive properties and valuable applications in wastewater treatment.

In this research, TiO₂ was synthesized and deposited effectively on cotton fibers and cellulose powder using ultrasound-assisted coating. Further, tetra butyl titanate was used as a precursor to the synthesis of TiO₂ nanoparticles. Reactive dye (red 195) was used in this study. X-ray Diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy were performed to prove the aptitude for the formation of crystal TiO2 on the cotton fibers and cellulose powder along with TiO₂ nanoparticles as well as to analyze the chemical structure. Decoloration of the wastewater was investigated through ultraviolet (UV-Visible) light at 30 min.

The experimental results revealed that the decolorization was completed at 2.0 min with the cellulose nano TiO₂ treatment whereas cotton nano TiO₂ treated solution contained reactive dyestuffs even after the treatment of 2 min. This was the fastest method up to now than all reported methods for sustainable decolorization of wastewater by absorption. Furthermore, this study explored that the cellulose TiO₂ nano-composite was more effective than the cotton TiO₂ nano-composite of decoloration wastewater for the eco-friendly remedy.

Cotton fibers and cellulose powder with nano-TiO₂, and only reactive dye (red 195) were tested.

With reactive dye-containing wastewater, it seems to be easier to get rid of the dye than to retain it, especially from dyeing of yarn, fabric, apparel, and as well as other sectors where dyestuffs are used.

This research would help to reduce pollution in the environment as well as save energy and cost.

Decoloration of wastewater treatment is an essential new track with nano-crystalline TiO2 to fast and efficient cleaning of reactive dyes containing wastewater used as a raw material.

The purpose of this study is to extract and characterize a novel natural dye from the leaves of Lannea coromandelica and the extraction with finding ways of dyeing cotton fabric using three mordants.

The colouring agents were extracted from the leaves of Lannea coromandelica using an aqueous extraction method. The extract was characterized using analysis methods of pH, gas chromatography-mass spectrometry (GC-MS), Fourier transform infrared (FTIR), ultraviolet-visible (UV-vis) and cyclic voltammetry measurement. The extract was applied to cotton fabric samples using a non-mordant and three mordants under the two mordanting methods. The dyeing performance of the extracted colouring agent was evaluated using colour fastness properties, colour strength (K/S) and colour space (CIE Lab).

The aqueous dye extract showed reddish-brown colour, and its pH was 5.94. The GC-MS analysis revealed that the dye extract from the leaves of Lannea coromandelica contained active chemical compounds. The UV-vis and FTIR analyses found that groups influenced the reddish-brown colour of the dye extraction. The cyclic voltammetry measurements discovered the electrochemical properties of the dye extraction. The mordanted fabric samples showed better colour fastness properties than the non-mordanted fabric sample. The K/S and CIE Lab results indicate that the cotton fabric samples dyed with mordants showed more significant dye affinities than non-mordanted fabric samples.

Researchers have never discovered that the Lannea coromandelica leaf extract is a natural dye for cotton fabric dyeing. The findings of this study showed that natural dyes extracted from Lannea coromandelica leaf could be an efficient colouring agent for use in cotton fabric.

Nanosensors have a wide range of applications because of their high sensitivity, selectivity and specificity. In the past decade, extensive and pervasive research related to nanosensors has led to significant progress in diverse fields, such as biomedicine, environmental monitoring and industrial process control. This led to better and more efficient detection and monitoring of physical and chemical properties at better resolution, opening new horizons in the development of novel technologies and applications for improved human health, environment protection, enhanced industrial processes, etc.

In this paper, the authors discuss the application of citation network analysis in the field of nanosensor research and development. Cluster analysis was carried out using papers published in the field of nanomaterial-based sensor research, and an in-depth analysis was carried out to identify significant clusters. The purpose of this study is to provide researchers to identify a pathway to the emerging areas in the field of nanosensor research. The authors have illustrated the knowledge base, knowledge domain and knowledge progression of nanosensor research using the citation analysis based on 3,636 Science Citation Index papers published during the period 2011 to 2021.

Among these papers, the bibliographic study identified 809 significant research publications, 11 clusters, 556 research sector keywords, 1,296 main authors, 139 referenced authors, 63 nations, 206 organizations and 42 journals. The authors have identified single quantum dot (QD)-based nanosensor for biological applications, carbon dot-based nanosensors, self-powered triboelectric nanogenerator-based nanosensor and genetically encoded nanosensor as the significant research hotspots that came to the fore in recent years. The future trend in nanosensor research might focus on the development of efficient and cost-effective designs for the detection of numerous environmental pollutants and biological molecules using mesostructured materials and QDs. It is also possible to optimize the detection methods using theoretical models, and generalized gradient approximation has great scope in sensor development.

The future trend in nanosensor research might focus on the development of efficient and cost-effective designs for the detection of numerous environmental pollutants and biological molecules using mesostructured materials and QDs. It is also possible to optimize the detection methods using theoretical models, and generalized gradient approximation has great scope in sensor development.

This is a novel bibliometric analysis in the area of “nanomaterial based sensor,” which is carried out in CiteSpace software.

The growing number of Muslim consumers pursuing a lifestyle of health and sustainability (LOHAS) under the conditions of the COVID-19 pandemic is interesting to assess; however, existing research focusing on this topic remains scarce. This study aims to address the research gaps and add to the body of knowledge from previous literature related to Islamic religiosity, environmental knowledge, LOHAS and Muslim customer well-being.

The sample used in this study is Muslim customers, including university students in a medical department and medical workers in Indonesia, using proportional random sampling methods with a total sample of 308 respondents.

The results demonstrate that Islamic religiosity positively and significantly impacts environmental knowledge, LOHAS and Muslim customer well-being. Similarly, environmental knowledge positively and significantly influences LOHAS, and subsequently, LOHAS fruitfully impacts Muslim customer well-being.

The results can assist managers of eco-friendly and healthy products or services and public policymakers in their effort to enhance LOHAS, particularly for Indonesian Muslim consumers to accomplish well-being considering their Islamic religiosity.

The results of this study help society protect a sustainable environment by increasing their environmental knowledge and LOHAS. Based on Islamic religion, society recognize how important environmental issues are to keep the environment safe in the future and build the culture of LOHAS to achieve their well-being.

This study contributes to the body of marketing literature for Muslim green consumer behaviour in particular and the LOHAS of the Muslim customer segment based on Islamic religiosity.