Search results
1 – 10 of 208Sandhya Ramalingam, Umma Habiba Hyder Ali and Sharmeela Chenniappan
This paper aims to design a dual mode X-band substrate integrated waveguide (SIW) bandpass filter in the conventional SIW structure. A pair of back-to-back square and split ring…
Abstract
Purpose
This paper aims to design a dual mode X-band substrate integrated waveguide (SIW) bandpass filter in the conventional SIW structure. A pair of back-to-back square and split ring resonator is introduced in the single-layer SIW bandpass filter. The various coupling configurations of SIW bandpass filter using split square ring slot resonator is designed to obtain dual resonant mode in the passband. It is shown that the measured results agree with the simulated results to meet compact size, lower the transmission coefficient, better reflection coefficient, sharp sideband rejection and minimal group delay.
Design/methodology/approach
A spurious suppression of wideband response is suppressed using an open stub in the transmission line. The width and length of the stub are tuned to suppress the wideband spurs in the stopband. The measured 3 dB bandwidth is from 8.76 to 14.24 GHz with a fractional bandwidth of 48.04% at a center frequency of 11.63 GHz, 12.59 GHz. The structure is analyzed using the equivalent circuit model, and the simulated analysis is based on an advanced design system software.
Findings
This paper discusses the characteristics of resonator below the waveguide cut-off frequency with their working principles and applications. Considering the difficulties in combining the resonators with a metallic waveguide, a new guided wave structure – the SIW is designed, which is synthesized on a planar substrate with linear periodic arrays of metallized via based on the printed circuit board.
Originality/value
This study has investigated the wave propagation problem of the SIW loaded by square ring slot-loaded resonator. The electric dipole nature of the resonator has been used to achieve a forward passband in a waveguide environment. The proposed filters have numerous advantages such as high-quality factor, low insertion loss, easy to integrate with the other planar circuits and, most importantly, compact size.
Details
Keywords
Yousra Ghazaoui, Mohammed EL Ghzaoui, Sudipta Das, BTP Madhav and Ali el Alami
This paper aims to present the design, fabrication and analysis of a wideband, enhanced gain 1 × 2 patch antenna array with a simple profile structure to meet the desired antenna…
Abstract
Purpose
This paper aims to present the design, fabrication and analysis of a wideband, enhanced gain 1 × 2 patch antenna array with a simple profile structure to meet the desired antenna traits, such as wide bandwidth, high gain and directional patterns expected for the upcoming fifth-generation (5G) wireless applications in the millimeter wave band. To enhance these parameters (bandwidth and gain), a new antenna geometry by using a T-junction power divider is presented.
Design/methodology/approach
The theory behind this paper is connected with advancements in the 5G communications related to antennas. The methodology used in this work is to design a high gain array antenna and to identify the best possible power divider to deliver the power in an optimized way. The design methodology adopts several steps like the selection of proper substrate material as per the design specification, size of the antenna as per the frequency of operation and application-specific environment condition. The simulation has been performed on the designed antenna in the electromagnetic simulation tool (high-frequency structure simulator [HFSS]), and optimization has been done with parametric analysis, and then the final array antenna model is proposed. The proposed array contains 2-patch elements excited by one port adapted to 50 Ω through a T-junction power divider. The 1 × 2 array configuration with the suggested geometry helps to improve the overall gain of the antenna, and the implementation of the T-junction power divider provides enhanced bandwidth. The proposed array designed using a 1.6 mm thick flame retardant substrate occupies a compact area of 14 × 12.14 mm2.
Findings
The prototype of the array antenna is fabricated and measured to validate the design concept. A good agreement has been reached between the measured and simulated antenna parameters. The measured results confirm its wideband and high gain characteristics, covering 24.77–28.80 GHz for S11= –10 dB with a peak gain of about 15.16 dB at 27.65 GHz.
Originality/value
The proposed antenna covers the bandwidth requirements of the 26 GHz n258 band (24.25–27.50 GHz) to be deployed in the UK and Europe. The suggested antenna structure also covers the federal communications commission (FCC)-regulated 28 GHz n261 band (27.5–28.35 GHz) to be deployed in America and Canada. The low profile, compact size, simple structure, wide bandwidth, high gain and desired directional radiation patterns confirm the applicability of the suggested array antenna for the upcoming 5 G wireless systems.
Details
Keywords
Deepinder Singh Wadhwa, Praveen Kumar Malik and Jaspal Singh Khinda
A compact low-cost antenna structure is proposed to augment the impedance-bandwidth in mm-wave range. Beside it, the paper also aimed to enhance high gain for n260 and n261-bands…
Abstract
Purpose
A compact low-cost antenna structure is proposed to augment the impedance-bandwidth in mm-wave range. Beside it, the paper also aimed to enhance high gain for n260 and n261-bands, suitable for futuristic communication systems.
Design/methodology/approach
Design consists of radiating patch and a partial ground plane with semi-circle arc for smooth flow of current. The lower corners of patch are gradually clipped away to make the patch nearly elliptical. Further, two tilted slots at an angle α = 15° are etched at the edges of the patch to augment bandwidth for mm-wave range. These slots divert the periphery current of semi elliptical patch towards center portion of antenna which ensures the participation in radiation of central portion of patch. The upper corners are also clipped away to limit the copper losses and smoothly flow of current. The proposed antenna is designed using HFSS and it is structured on inexpensive FR4 substrate of size 27.5 × 20 mm2.
Findings
It supports enormous −10 dB bandwidth of 5.86–40GHz (148.89%) even though use of high loss-tangent material and high gain for 28 GHz (27.50–28.35 GHz) n261–band and 37 GHz (37–38.6 GHz) and 39 GHz (38.6–40GHz) n260–bands with a peak-gain of 8.76 dBi, 10.8 dBi and 9.92 dBi, respectively.
Originality/value
The proposed methodology of design is very useful to enhance impedance bandwidth to cover all C–, X–, Ku–, K– and Ka–band even though use of low cost material with high loss tangent. In recent literature, the designs were implemented with a costly material and having very low loss tangent and covers partial suggest bands.
Details
Keywords
Modern wireless communications need novel microwave components that can be effectively used for high data rate and low-power applications. The operating environment decides the…
Abstract
Purpose
Modern wireless communications need novel microwave components that can be effectively used for high data rate and low-power applications. The operating environment decides the severity of the noise coupled to the transceiver system from the ambient environment. In a deep fading environment, narrowband systems fail where the wideband systems come for rescue. Thus, the microwave components are ought to switch between the narrowband and wideband states. This paper aims to study the design of a bandpass filter to meet the requirements by appropriately switching between the dual narrowband frequencies and single ultra-wideband frequency band.
Design/methodology/approach
The design and implementation of a compact microwave filter with reconfigurable bandwidth characteristics are presented in this paper. The proposed filter is constructed using a hexagonal ring with shorted perturbation along one corner. The filter is capacitively coupled to the external excitation source. External stubs are connected to the corners of the hexagonal resonator to obtain dual passband characteristics centred at 2.1 and 4.5 GHz. The external stubs are configured to achieve bandwidth reconfigurable characteristics. PIN diodes are used with a suitable biasing network to obtain reconfiguration. In the reconfigured state, the proposed two-port filter offers a continuous bandwidth from 2.1 to 5.9 GHz. The roll-off rate along the band edges is improved by increasing the order of the filter.
Findings
The proposed filter operates in two states. In state 1, the filter operates with dual frequencies centred around 2 and 4.5 GHz with insertion loss less than <1 dB and return loss greater than 13 dB with a peak return loss of 21 and 31 dB at 2.1 and 2.15 GHz, respectively. In state 2, the filter operates from 2.1 to 5.9 GHz with insertion loss less than 1 dB and return loss greater than 12 dB. The filter exhibits four-pole characteristics with a peak return loss greater than 22 dB. Thus, the fractional bandwidth of the proposed filter is 17% and 16% in state 1, whereas the fractional bandwidth is 95% in state 2.
Originality/value
The proposed filter is the first of its kind to simultaneously offer miniaturization and bandwidth reconfiguration. The proposed second-order filter has two-pole characteristics in the narrowband state, whereas four-pole characteristics are realized in the wideband state. The growing interest in 4G and 5G wireless communications makes the proposed filter a suitable candidate for operation in the rich scattering environment.
Details
Keywords
Arun Kumar Gande, Souma Guha Mallick, Bijit Biswas, Sayan Chatterjee and Dipak Ranjan Poddar
This paper aims to present a compact, broadband substrate integrated waveguide (SIW) three-way power divider with improved isolation based on six-port SIW coupler.
Abstract
Purpose
This paper aims to present a compact, broadband substrate integrated waveguide (SIW) three-way power divider with improved isolation based on six-port SIW coupler.
Design/methodology/approach
The power coupling among the three output ports occurs due to short openings in the narrow walls of the central SIW channel. Performance improvement in the isolation and return loss among ports is achieved using matching posts placed at the input and output ends of the coupling region. This enhances the coupling between TE10 and TE30 modes. The input matching ports enhance the return loss, whereas the isolation is alleviated by both the input and output matching posts. The bandwidth enhancement is achieved by optimizing the outer SIW channel widths.
Findings
The measured fractional bandwidth of 27.3% with over 15 dB of isolation and return loss is achieved. The coupling length is 1.55 λg at the centre frequency. The power divider achieves better than 15 dB isolation between non-adjacent output ports. The measured reflection and isolation coefficients are in close agreement with simulated results over 8.2 to 10.8 GHz.
Practical implications
Isolation between the adjacent and non-adjacent ports is an important parameter as the reflections from these ports will interfere with signals from other ports reducing the fractional bandwidth of the power divider and affecting the overall performance of the transmitters and receivers.
Originality/value
The authors present the enhancement of isolation between the output non-adjacent ports by optimizing the SIW channel width and matching post in the coupling region to reduce the reflected signals from non-adjacent ports entering into other ports. To the author’s knowledge, this is the only SIW three-way power divider paper showing non-adjacent port isolation among six-port couplers based three-way power dividers.
Details
Keywords
This paper is aimed to study the design of a miniaturized filter with tri-band characteristics. In this paper, perturbation is used to realize circuit miniaturization and…
Abstract
Purpose
This paper is aimed to study the design of a miniaturized filter with tri-band characteristics. In this paper, perturbation is used to realize circuit miniaturization and multi-band by exploiting the inductive property. During this process, vias are added for twofold benefit, namely, circuit miniaturization and enhanced frequency selectivity at high frequency. Thus, with the introduction of the shorting via, the single-band dual-mode bandpass filter is converted into a tri-band filter with a smaller electrical size.
Design/methodology/approach
This paper presents the design and characterization of a miniaturized two-port filter with tri-band operating characteristics. The proposed filter is constructed using a square patch resonator operating at 5.2 GHz with a capacitively coupled feed configuration. A square perturbation is added to the corner of the square patch to achieve diagonal symmetry and to excite dual mode. The perturbation offers a sharp transmission zero defining bandwidth of the proposed filter. In addition, a shorting post is introduced to achieve an 88% size reduction by lowering the operating frequency to 1.8 GHz.
Findings
The prototype filter has insertion less than 1.2 dB and return loss better than 12 dB throughout all the realized frequency bands. The prototype filter is fabricated and the simulation results are validated using experimental measurements. The realized fractional bandwidths of the proposed bandpass filter are 11/5.6/1 at 1.8/4.6/5.85 GHz, respectively. The quality factor of the proposed antenna is greater than 80 and a peak Q-factor of 387 is realized at 5.85 GHz. The high Q-factor indicates low loss and improved selectivity. The rejection levels in the stopband are greater than 20 dB.
Originality/value
The results indicate that the proposed filter is a suitable choice for low-power small-scale wireless systems operating in the microwave bands. The realized filter has the smallest footprint of 0.36λeff × 0.19λeff where λeff is the effective wavelength calculated at the lowest frequency of operation.
Details
Keywords
Jasmine Vijithra A. and Gulam Nabi Alsath Mohammed
This study aims to design a compact filtering monopole antenna for 5G communication. The design is most suited for various applications within the frequency range of 2.2–3.8 GHz…
Abstract
Purpose
This study aims to design a compact filtering monopole antenna for 5G communication. The design is most suited for various applications within the frequency range of 2.2–3.8 GHz. It offers enhanced bandwidth and reasonable gain with wide-stopband performance.
Design/methodology/approach
A low-pass filter (LPF) of complementary split ring resonator (CSRR) with short-circuited stub lines is integrated with a compact defected coplanar waveguide fed truncated circular monopole ultrawideband (UWB) antenna. The reference UWB antenna etched on an FR4 substrate was coupled to the designed LPF to transform the UWB antenna into a wideband antenna. The effect of coupling is analyzed based on the real and imaginary responses of the terminal impedance (ZT) curve. Three short-circuited stub lines of asymmetric lengths are added to the CSRR LPF to suppress harmonics, thereby enhancing the stopband performance and impedance matching between the elements. The proposed filtering antenna is fabricated using a photolithography process, and the corresponding results are measured using a network analyzer (N9951A). The radiation parameters of the proposed filtering monopole antenna are tested in the anechoic chamber. The simulated/measured results are compared and are found in agreement with each other.
Findings
The proposed design suppresses 6.5f0 harmonics, resulting in wide stopband performance and increased gain selectivity at the transition edge. A peak suppression of −41 dB and an average suppression of −18 dB were attained throughout the stopband. An operating fractional bandwidth of 54.5%/143% with a peak gain of 3 dBi/5 dBi was obtained. The proposed filtering antenna supports 5G applications such as WiMAX, WLAN, n7, n38 IMT-E, n30 WCS, n40 TDD, n41 TDD, n48 TDD, n78 TDD and n90 TDD.
Originality/value
The proposed design is novel and compact and has a wide application in 5G communication. With the filter, the antenna operates in wideband, and without the filter, it operates in UWB. Besides, it offers enhanced stopband performance with high gain selectivity at the transition edge. Comparatively, a 50% improvement in bandwidth, 52% improvement in size reduction and 33% improvement in harmonic suppression are attained.
Details
Keywords
Atul Varshney, Vipul Sharma, T. Mary Neebha and N. Prasanthi Kumari
This paper aims to present a low-cost, edge-fed, windmill-shaped, notch-band eliminator, circular monopole antenna which is practically loaded with a complementary split ring…
Abstract
Purpose
This paper aims to present a low-cost, edge-fed, windmill-shaped, notch-band eliminator, circular monopole antenna which is practically loaded with a complementary split ring resonator (CSRR) in the middle of the radiating conductor and also uses a partial ground to obtain wide-band performance.
Design/methodology/approach
To compensate for the reduced value of gain and reflection coefficient because of the full (complete) ground plane at the bottom of the substrate, the antenna is further loaded with a partial ground and a CSRR. The reduction in the length of ground near the feed line improves the impedance bandwidth, and introduced CSRR results in improved gain with an additional resonance spike. This results in a peak gain 3.895dBi at the designed frequency 2.45 GHz. The extending of three arms in the circular patch not only led to an increase of peak gain by 4.044dBi but also eliminated the notch band and improved the fractional bandwidth 1.65–2.92 GHz.
Findings
The work reports a –10dB bandwidth from 1.63 GHz to 2.91 GHz, which covers traditional coverage applications and new specific uses applications such as narrow LTE bands for future internet of things (NB-IoT) machine-to-machine communications 1.8/1.9/2.1/2.3/2.5/2.6 GHz, industry, automation and business-critical cases (2.1/2.3/2.6 GHz), industrial, society and medical applications such as Wi-MAX (3.5 GHz), Wi-Fi3 (2.45 GHz), GSM (1.9 GHz), public safety band, Bluetooth (2.40–2.485 GHz), Zigbee (2.40–2.48Ghz), industrial scientific medical (ISM) band (2.4–2.5 GHz), WCDMA (1.9, 2.1 GHz), 3 G (2.1 GHz), 4 G LTE (2.1–2.5 GHz) and other personal communication services applications. The estimated RLC electrical equivalent circuit is also presented at the end.
Practical implications
Because of full coverage of Bluetooth, Zigbee, WiFi3 and ISM band, the proposed fabricated antenna is suitable for low power, low data rate and wireless/wired short-range IoT-enabled medical applications.
Originality/value
The antenna is fabricated on a piece (66.4 mm × 66.4 mm × 1.6 mm) of low-cost low profile FR-4 epoxy substrate (0.54
Details
Keywords
Atul Varshney and Vipul Sharma
This paper aims to present the design development and measurement of two aerodynamic slotted X-bands back-to-back planer substrate-integrated rectangular waveguide (SIRWG/SIW) to…
Abstract
Purpose
This paper aims to present the design development and measurement of two aerodynamic slotted X-bands back-to-back planer substrate-integrated rectangular waveguide (SIRWG/SIW) to Microstrip (MS) line transition for satellite and RADAR applications. It facilitates the realization of nonplanar (waveguide-based) circuits into planar form for easy integration with other planar (microstrip) devices, circuits and systems. This paper describes the design of a SIW to microstrip transition. The transition is broadband covering the frequency range of 8–12 GHz. The design and interconnection of microwave components like filters, power dividers, resonators, satellite dishes, sensors, transmitters and transponders are further aided by these transitions. A common planar interconnect is designed with better reflection coefficient/return loss (RL) (S11/S22 ≤ 10 dB), transmission coefficient/insertion loss (IL) (S12/S21: 0–3.0 dB) and ultra-wideband bandwidth on low profile FR-4 substrate for X-band and Ku-band functioning to interconnect modern era MIC/MMIC circuits, components and devices.
Design/methodology/approach
Two series of metal via (6 via/row) have been used so that all surface current and electric field vectors are confined within the metallic via-wall in SIW length. Introduced aerodynamic slots in tapered portions achieve excellent impedance matching and tapered junctions with SIW are mitered for fine tuning to achieve minimum reflections and improved transmissions at X-band center frequency.
Findings
Using this method, the measured IL and RLs are found in concord with simulated results in full X-band (8.22–12.4 GHz). RLC T-equivalent and p-equivalent electrical circuits of the proposed design are presented at the end.
Practical implications
The measurement of the prototype has been carried out by an available low-cost X-band microwave bench and with a Keysight E4416A power meter in the microwave laboratory.
Originality/value
The transition is fabricated on FR-4 substrate with compact size 14 mm × 21.35 mm × 1.6 mm and hence economical with IL lie within limits 0.6–1 dB and RL is lower than −10 dB in bandwidth 7.05–17.10 GHz. Because of such outstanding fractional bandwidth (FBW: 100.5%), the transition could also be useful for Ku-band with IL close to 1.6 dB.
Details
Keywords
Keyur Mahant, Hiren K. Mewada, Amit V. Patel, Alpesh Vala and Jitendra Chaudhari
This paper aims to present, design and implement a novel half-mode substrate integrated waveguide (HMSIW)-based narrow bandpass filter, which offers advantages like low insertion…
Abstract
Purpose
This paper aims to present, design and implement a novel half-mode substrate integrated waveguide (HMSIW)-based narrow bandpass filter, which offers advantages like low insertion loss, compact size and high selectivity. Proposed filter will be used in the K-band automotive radar application.
Design/methodology/approach
The filtering response in the proposed design is achieved by inserting inductive posts in the HMSIW cavity. Ansoft high frequency structure Simulator (HFSS) is used for the simulation of the proposed structure, which is a three-dimensional full-wave solver using the finite element method (FEM). The proposed filter is fabricated on the dielectric material RT duroid 5,880 with the dielectric constant ɛr = 2.2, dissipation factor t and = 4 × 10–4 and height h = 0.508 mm.
Findings
Frequency tuning is also carried out by changing the lateral distance between two inductive posts. Moreover, a comparison of the proposed structure with the previously published work is presented. Proposed method provides the unique advantages such as low insertion loss, high selectivity and compact in size.
Originality/value
Indigenous method has been used for the development of the filter. Proposed filter will be used in transmitter subsystem of the K-band radar system operating at the center frequency of 11.2 GHz. Measurement results are well-matched with the simulated one. Obtained measured result shows return loss of 20.39 dB and insertion loss of 1.59 dB with 3 dB fractional bandwidth (FBW) of 2.58% at the center frequency of 11.2 GHz.
Details