Search results

This paper introduces a simple computational model for the analysis on the solder ball shear testing conditions. Both two‐dimensional (2‐D) and three‐dimensional (3‐D) finite element models are used to investigate the effect of shear ram speed on the solder ball shear strength of plastic ball grid array (PBGA) packages. An effective thickness is identified for the 2‐D finite element analysis. By using this effective thickness as a scale factor, it is shown that the 2D model is feasible for the study of 3‐D problems. The computational model is validated by experimental data in terms of load‐displacement curves. The results from both testing and modeling indicate that the shear ram speed has a substantial effect on the solder ball shear strength. In general, faster ram speed can result in higher ball shear strength. Therefore, the characterization of solder ball shear strength is loading rate‐dependent.

The main purpose of this paper is to investigate the vibration isolation performance of a quasi-zero stiffness (QZS) metastructure by employing the band gap (BG) mechanism.

The metastructure QZS characteristic was investigated through static analysis by numerical simulation. Based on that, the BG mechanism is primarily used in this article to investigate the wave propagation characteristics of this structure. The model's dispersion relation is then examined using theoretical (perturbation method) and finite element techniques. The dynamic response of the finite-size systems and experimental analysis is used to confirm the vibration mitigation property under investigation. Finally, the model's ability to absorb energy was examined and contrasted with a traditional model.

The analytical analysis reveals the dispersion curve and the effect of the nonlinear parameter on the curve shifting. The dispersion curve in the finite element method (FEM) result depicts five complete BGs within the range of 0–1,000 Hz, and the BG width accounted for 67.4% of the frequency concerned (0–1,000 Hz). Eigenmodes of the dispersion curves were analyzed to investigate the BG formation mechanisms. The dependence of BG opening and closure on structure parameters was also studied. Finally, the energy absorption property of the QZS metastructure was evaluated by comparing it with a classical model. The QZS structure absorbs 4.08 J/Kg compared to the 3.69 J/Kg absorbed by the classical model, which reveals that the QZS demonstrates better energy absorption performance. Based on the BG mechanism, it is clear that this model is an excellent vibration isolator, and the study reveals the frequencies at which complete vibration mitigation is achieved. As a result, this model could be a promising candidate for vibration mitigation engineering structures and energy absorption.

The tough vibration issue, which is primarily experienced in mechanical equipment, will be resolved in this study. This study provides a precise understanding of the QZS metastructure's isolation of vibration, including the frequencies at which this isolation occurs.

This paper aims to model the performances of frames structures by comparing the predictions of ordinary control concrete (CC) and concretes reinforced by fibers. Two types of steel fibers were used in this work, industrial steel fibers (ISF) and tire-reclaimed fibers obtained by cutting virgin steel tire-cord to 50 mm, noticed virgin steel fibers (VSF). In total, 3% of VSF are used. The results obtained in this paper clearly show the contribution of fibers in improving the global and local behavior of the frames structures. VSF gives the same or better overall behavior as the use of industrial fibers for the same percentage of fibers, with the advantage that VSF contributes to the protection of the environment and limit the wastage of steel.

This work was carried out using the commercial finite element code Abaqus/Explicit. The behavior of the different concretes used in this study was modeled by the concrete damage plasticity (CDP) constitutive law. The methodology adopted to complete this work consisted in identifying, by calibration of the available experimental results with the numerical predictions, the parameters of the corresponding CDP model for each of the concretes used in this work. To this end, the authors have successively identified the CDP parameters for the CC-V (control concrete used by Vecchio and Emara, 1992) used in frame structure (R + 1). Subsequently, the CDP parameters of the CC-T (control concrete used by Tlemat, 2004), the CVSF (concrete with virgin steel fibers) and the CISF-1 (concrete with industrial steel fibers type 1, ISF-1) are identified using the experimental results of beams under bending tests. Once the model parameters were determined for each concrete, the authors conducted a series of simulations to show the benefit of introducing claimed and industrial fibers in frame structure (R + 1) and (R + 2). This approach recommends the use of concrete reinforced with steel fibers, mainly 6% by mass of VSF and ISF-1, in place of ordinary concrete in new construction to increase the resistance of structures and contribute, if applicable, to the protection of the environment.

The main findings of this study can be summarized by: the strength and ductility of the frames structures made of concrete fiber are significantly increased. The use of tire-reclaimed steel fibers (VSF) gives the same or better overall behavior as the use of industrial fibers. In addition to their good mechanical contribution, the tire-reclaimed fibers contribute to the protection of the environment and limit the wastage of steel. The use of fibers reduces the cracking zones in concrete fiber frames structures. The usefulness of distinguishing the interstory displacement limits set by codes, in particular, uniform building code (UBC-97), for ordinary concretes and concrete reinforced with fibers is addressed.

The contribution of tire-reclaimed and industrial fibers on the strength and ductility of reinforced concrete-frames structures is addressed. The use of tire-reclaimed steel fibers gives the same or better overall behavior as the use of industrial fibers, the tire-reclaimed fibers having the advantage of contributing to the protection of the environment and limiting the wastage of steel. The paper also points to the usefulness of distinguishing the interstory displacement limits set by codes, in particular UBC-97, for ordinary concrete and concrete reinforced with fibers, in accordance to the predictions of the capacity curves.

Sandwich construction has developed and has become an integral part of lightweight construction. In the recent projects, it has been shown that by using sandwich panels as stabilizing members, a considerable amount of savings of steel can be achieved for structural members at ambient temperature. These stabilizing effects may also help to achieve similar savings in case of fire.

The response of a sandwich single panel as well as the behaviour of the whole structure at ambient temperature and in case of fire is influenced by joints between the sandwich panels and the sub-structure. The fastenings used to fix the sandwich panels to a sub-structure may be loaded by shear forces caused by self-weight, live loads or diaphragm action. Therefore, an experimental investigation was conducted to investigate the shear behaviour of sandwich panel joints in fire.

This paper summarized briefly the experimental results, numerical simulations and analytical models on the shear behaviour of sandwich panel joints at ambient and elevated temperatures.

The work is limited to studied types of screws and sandwich panels which are generally used in current sandwich construction.

These stabilizing effects in sandwich construction help to achieve savings in case of fire.

Sandwich construction has developed and has become an integral part of lightweight construction. In the recent projects, it has been shown that by using sandwich panels as stabilizing members, a considerable amount of savings of steel can be achieved for structural members at ambient temperature. These stabilizing effects help to achieve similar savings in case of fire.

This paper summarized briefly the experimental results, numerical simulations and analytical models on the shear behaviour of sandwich panel joints at ambient and elevated temperatures, which were not published yet.

The purpose of this study is to develop jute-glass hybrid fibre reinforced polyester-based bio-composites using an indigenously developed pultrusion set-up and to present a detailed discussion on their mechanical characterization.

The work was carried out to observe the hybridization effect of natural and synthetic fibres in combination with hybrid fillers loading mainly on strength and other properties. The used hybrid fillers were a combination of 9 Wt.% of carbon black%, 6 Wt.% of eggshell ash powder and 6 Wt.% of coconut coir ash powder. A lab-based developed pultrusion set-up was used to develop these hybrid GJFRP composites of 1,500 mm length. The developed composites were tested for tensile strength, compressive strength and impact strength.

The maximum tensile, compressive and impact strength obtained are 88.37 MPa, 56.13 MPa and 731.91 J/m from 9 Wt.%, 9 Wt.% and 0 Wt.% of hybrid fillers loading, respectively. Breaking energy was found maximum as 7.31 J in hybrid glass-jute hybrid fibre reinforced plastic composites with no filler loading and it was observed that filler loading was decreasing the impact strength of developed hybrid composites. Shrinkage and its variations in the diameter of the finally developed cylindrical shape composites were observed after cooling and solidification. Scanning electron microscopy was used to observe the internal cracks, bonding of fibres and resin, voids, etc.

Development of hybrid filler based novel eco-friendly bio-composites and its experimental investigation on the impact strength, tensile strength and compressive strength has not been attempted yet.

The purpose of this paper is to study the behavior of negative stiffness beams when arranged in a honeycomb configuration and to compare the energy absorption capacity of these negative stiffness honeycombs with regular honeycombs of equivalent relative densities.

A negative stiffness honeycomb is fabricated in nylon 11 using selective laser sintering. Its force-displacement behavior is simulated with finite element analysis and experimentally evaluated under quasi-static displacement loading. Similarly, a hexagonal honeycomb of equivalent relative density is also fabricated and tested. The energy absorbed for both specimens is computed from the resulting force-displacement curves. The beam geometry of the negative stiffness honeycomb is optimized for maximum energy absorption per unit mass of material.

Negative stiffness honeycombs exhibit relatively large positive stiffness, followed by a region of plateau stress as the cell walls buckle, similar to regular hexagonal honeycombs, but unlike regular honeycombs, they demonstrate full recovery after compression. Representative specimens are found to absorb about 65 per cent of the energy incident on them. Optimizing the negative stiffness beam geometry can result in energy-absorbing capacities comparable to regular honeycombs of similar relative densities.

The honeycombs were subject to quasi-static displacement loading. To study shock isolation under impact loads, force-controlled loading is desirable. However, the energy absorption performance of the negative stiffness honeycombs is expected to improve under force-controlled conditions. Additional experimentation is needed to investigate the rate sensitivity of the force-displacement behavior of the negative stiffness honeycombs, and specimens with various geometries should be investigated.

The findings of this study indicate that recoverable energy absorption is possible using negative stiffness honeycombs without sacrificing the high energy-absorbing capacity of regular honeycombs. The honeycombs can find usefulness in a number of unique applications requiring recoverable shock isolation, such as bumpers, helmets and other personal protection devices. A patent application has been filed for the negative stiffness honeycomb design.

The aim of this study was to understand the stick-slip properties of single and multiple yarn pull-out in dry and treated polyester satin woven fabric in boundary regions.

Polyester satin pattern woven fabric was used to conduct the pull-out tests in order to examining the kinetic region of the force-displacement curve. Data generated from this research help the authors to obtain stick-slip force and accumulative retraction force.

It was found that stick-slip force and accumulative retraction force depend on the number of pulled ends in the fabric, fabric sample dimensions and softening treatments. Stick-slip forces of polyester satin fabric in the multiple yarn pull-out test were higher than those of the single yarn pull-out test. Stick-slip force in single and multiple yarn pull-out tests in the dry polyester satin fabric was generally higher than those of the softening treated polyester satin fabric. In addition, the warp directional single and multiple yarn stick-slip and accumulative retraction forces in the dry and softening treated polyester fabrics were generally higher than those in the weft direction in the fabric edges due to fabric density. On the other hand, the amount of stick-slip force was related to the number of interlacement points in the fabric, whereas the amount of accumulative retraction force was related to fabric structural response.

The mechanism of stick-slip and accumulative retraction force of dry-treated polyester satin pattern woven fabrics were explained. This research could be valuable for development of multifunctional fabrics in technical textiles and ballistic.

The purpose of this paper is to study the variation of the mechanical strength and failure modes of solder balls with reducing diameters under conditions of multiple reflows.

The solder balls with diameters from 250 to 760 µm were mounted on the copper-clad laminate by 1-5 reflows. The strength of the solder balls was tested by the single ball shear test and pull test, respectively. The failure modes of tested samples were identified by combing morphologies of fracture surfaces and force-displacement curves. The stresses were revealed and the failure explanations were assisted by the finite element analysis for the shear test of single solder ball.

The average strength of a smaller solder ball (e.g. 250 µm in diameter) is higher than that of a larger one (e.g. 760 µm in diameter). The strength of smaller solder balls is more highly variable with multiple reflows than larger diameters balls, where the strength increased mostly with the number of reflows. According to load-displacement curves or fracture surface morphologies, the failure modes of solder ball in the shear and pull tests can be categorized into three kinds.

The strength of solder balls will not deteriorate when the diameter of solder ball is decreased with a reflow, but a smaller solder ball has a higher failure risk after multiple reflows. The failure modes for shear and pull tests can be identified quickly by the combination of force-displacement curves and the morphologies of fracture surfaces.

The riveting with blind rivets is extensively used in railway structures, which are mainly composed of aluminium. The lack of knowledge in this process makes the railway constructors to over‐proportion the number of rivets used in the structures and to perform a lot of tests in order to validate them. To better understand the different phenomena occurring during this process, a numerical model has been made, based on experimental tests. Considering the diversity of assemblies found in a railway structure (various diameter values of rivet, thickness and multiple materials of sheet metal assemblies, etc.), we propose a methodology based on the simulation of their behaviour. The numerical model allows to avoid high characterisation costs based only on experience.

The purpose of this paper is to study the behaviour of glass reinforced epoxy tubes subjected to repeated indentation loads at two non-coincident indentations 180° apart.

Four geometrically scaled specimens ranging from 100 to 400 mm diameter were used in repeated indentation tests. Force, displacement and damage growth were recorded for loading and unloading until the indenter returned to its original starting point.

Similar scaled trends were observed between the non-coincidental loadings. Unlike reported response form coincidental loadings, the responses from non-coincidental loadings yield lower values for bending stiffness and peak load.

The differences in behaviour of the specimen between non-coincident loadings were attributed to reductions in fracture toughness and circumferential modulus.

Distant non-interacting damage and delamination around the circumference does reduce the structural performance.

Behaviour of composite tubes under different loading conditions, for example low speed impact or quasi static indentation, is widely studied, however little attention has been given to the repeated loading incidents.