Search results

The area behind the engine/wing junction of conventional civil aircraft configurations with underwing-mounted turbofans is susceptible to local flow separation at high angles of attack, which potentially impacts maximum lift performance of the aircraft. This paper aims to present the design, testing and optimization of two distinct systems of fluidic actuation dedicated to reduce separation at the engine/wing junction.

Active flow control applied at the unprotected leading edge inboard of the engine pylon has shown considerable potential to alleviate or even eliminate local flow separation, and consequently regain maximum lift performance. Two actuator systems, pulsed jet actuators with and without net mass flux, are tested and optimized with respect to an upcoming large-scale wind tunnel test to assess the effect of active flow control on the flow behavior. The requirements and parameters of the flow control hardware are set by numerical simulations of project partners.

The results of ground test show that full modulation of the jets of the non-zero mass flux actuator is achieved. In addition, it could be shown that the required parameters can be satisfied at design mass flow, and that pressure levels are within bounds. Furthermore, a new generation of zero-net mass flux actuators with improved performance is presented and described. This flow control system includes the actuator devices, their integration, as well as the drive and control electronics system that is used to drive groups of actuators.

The originality is given by the application of the two flow control systems in a scheduled large-scale wind tunnel test.

The purpose of this paper is to examine entropy generation rate in the flow and temperature field due pulsed impinging jet on to a flat plate. Heat transfer of pulsed impinging jets has been investigated by many researchers. Entropy generation is one of the parameters related to the second law of thermodynamics which must be analyzed in processes with heat transfer and fluid flow in order to design efficient systems. Effect of velocity profile parameters and various nozzle to plate distances on viscous and thermal entropy generation are investigated.

In this study, the flow and temperature field of a pulsed turbulent impinging jet are simulated numerically by the finite volume method with appropriate boundary conditions. Then, flow and temperature results are used to calculate the rate of entropy generation due to heat transfer and viscous dissipation.

Results show that maximum viscous and thermal entropy generation occurs in the lowest nozzle to plate distance and entropy generation decreases as the nozzle to plate distance increases. Entropy generation in the two early phase of a period in the most frequencies is more than steady state whereas a completely opposite behavior happens in the two latter phase. Increase in the pulsation frequency and amplitude leads to enhancement in entropy generation because of larger temperature and velocity gradients. This phenomenon appears second and even third peaks in entropy generation plots in higher pulsation frequency and amplitude.

The predictions may be extended to include various pulsation signal shape, multiple jet configuration, the radiation effect and phase difference between jets.

The results of this paper are a valuable source of information for active control of transport phenomena in impinging jet configurations which is used in different industrial applications such as cooling, heating and drying processes.

In this paper the entropy generation of pulsed impinging jet was studied for the first time and a comprehensive discussion on numerical results is provided.

In the European project AFLoNext, active flow control (AFC) measures were adopted in the wing tip extension leading edge to suppress flow separation. It is expected that the designed wing tip extension may improve aerodynamic efficiency by about 2 per cent in terms of fuel consumption and emissions. As the leading edge of the wing tip is not protected with high-lift device, flow separation occurs earlier than over the inboard wing in the take-off/landing configuration. The aim of this study is the adoption of AFC to delay wing tip stall and to improve lift-to-drag ratio.

Several actuator locations and AFC strategies were tested with computational fluid dynamics. The first approach was “standard” one with physical modeling of the actuators, and the second one was focused on the volume forcing method. The actuators location and the forcing plane close to separation line of the reference configuration were chose to enhance the flow with steady and pulsed jet blowing. Dependence of the lift-to-drag benefit with respect to injected mass flow is investigated.

The mechanism of flow separation onset is identified as the interaction of slat-end and wing tip vortices. These vortices moving toward each other with increasing angle of attack (AoA) interact and cause the flow separation. AFC is applied to control the slat-end vortex and the inboard movement of the wing tip vortex to suppress their interaction. The separation onset has been postponed by about 2° of AoA; the value of ift-to-drag (L/D) was improved up to 22 per cent for the most beneficial cases.

The AFC using the steady or pulsed blowing (PB) was proved to be an effective tool for delaying the flow separation. Although better values of L/D have been reached using steady blowing, it is also shown that PB case with a duty cycle of 0.5 needs only one half of the mass flow.

Two approaches of different levels of complexity are studied and compared. The first is based on physical modeling of actuator cavities, while the second relies on volume forcing method which does not require detailed actuator modeling. Both approaches give consistent results.

This paper aims to present an experimental investigation of an active flow control solution mounted at rear of a sport utility vehicle (SUV) with the objective of drag reduction, thanks to a selection of flow control parameters leading to a pressure increase on the tailgate.

A flow control design of experiments was conducted with a pulsed jet system mounted on the top and sides of the rear window of the vehicle. The wall pressure, instantaneous velocity and drag were measured with this prototype in a wind tunnel. A dynamic modal decomposition (DMD) analysis of the pressure enables to describe the pressure fluctuations. Fluid dynamic computations show relation between pressure and velocity fields.

Measurements with this prototype in the wind tunnel revealed small improvements in drag for the best flow control configurations. This small benefit is because of the core of the upper span wise vortex further away from the rear window than the lower span wise vortex. These small improvements in drag were confirmed with pressure measurements on the rear window and tailgate. The DMD analysis of the surface pressure showed a low frequency pendulum oscillation on the lower area of the tailgate, linked with low velocity frequencies in the shear layers near the tailgate.

Experimental and numerical results show interest to increase pressure at bottom of the rear end of this SUV prototype. The dynamic description of the wall pressure shows importance of flow control solutions reducing pressure fluctuations at low frequencies in the lower area of the tailgate.

The purpose of this study is to investigate the coherent structures of pulsed opposing jets by large eddy simulation (LES) model and proper orthogonal decomposition (POD) snapshot method. Flow pulsation as an active flow control method is considered for the enhancement of transport phenomena in impinging jets. The effect of flow pulsation parameters such as pulsation signal shape and frequency on the vortical coherent structures, the energy content of primary modes and their variation are studied numerically.

In this study, flow field of turbulent pulsating opposing jets has been simulated using LES. The result of the simulation in different time steps (snapshots) are stored and POD is applied on the snapshots. In this study, the POD method and calculation of spatial modes has been done using OpenFOAM, and time coefficients have been calculated using a MATLAB code.

The results of this study show that the flow excitation has a great effect on the coherent structure formation and the energy containment of fundamental modes of the flow. When the flow was excited by a harmonic sinusoidal or step function, the turbulent kinetic energy accumulated in the set of primary modes. On the other hand, the pulsed opposing jets had more regularity compared to the steady jets. The shapes, patterns and energy values of dominant modes depended on the inlet pulsation signal. An increase in pulsation frequency leads to an augmentation in energy content of the primary modes.

The predictions may be extended to include various pulsation conditions such as: various amplitudes, Reynolds number and aspect ratio.

The results of this study are a valuable source of information for active control of transport phenomena in opposing jet configurations which is used in different industrial applications such as cooling, combustion, reactors, heating and drying processes.

In this study, the coherent structures and energy content of primary modes was studied for the first time by LES model and POD snapshot method and a comprehensive discussion on numerical results is provided.

Electrostatic precipitators (ESP) and fabric filters (FF) are the main air pollution control equipment utilized to clean dust laden fumes from utility boilers. The choice among these systems depends on specific site conditions such as dust characteristics, required efficiency, gas flowrate and temperature. ESP are generally characterized by higher capital investments and lower operating charges, while the opposite may be said for FF baghouses. As a consequence, ESP present higher total costs when high specific collection areas are required, as happens in the case of low‐sulfur high‐resistivity dust. However, significant reductions in both capital investment and operating charges may be obtained with pulsed energization of precipitators working in severe back corona conditions. This possibility greatly enlarges the field of applications in which ESP are a lower cost option compared to fabric filters. In the paper an economic comparison of pulse energized ESP, with conventional ESP, reverse‐air, shaker, and pulse‐jet baghouses is performed. A mapping of the operating conditions in which the adoption of each examined control technology is economically convenient is also defined.

The purpose of this paper is to evaluate the synthetic jet actuator design's performance based on piezoelectric diaphragms that can be appropriately used for flow separation control.

Design the synthetic jet actuators by means of estimating the several parameters and non‐dimensional parameters. Understanding the relationship and coupling effects of these parameters on the actuator to produce exit air jet required. Experiments were conducted to measure the exit air jet velocity using a hot‐wire anemometry and determine the good operational frequencies and voltages of the actuators for different cavity volume.

The performance of synthetic jet actuator is not consistent to a particular given frequency and it depends on design configurations. Each actuator will give a very good speed for a certain frequency. The results show that the exit air jet velocity increases would be better if the cavity volume is reduced and if the input voltage is increased to certain limits.

The limit of input voltage for the actuators that can be achieved for good jet speed is 2V of about 205V output voltage for each frequency. The jet speed obtained is sufficient enough to control the separation for an aircraft which has a small wing chord and low speed. Therefore, more studies are needed to optimize the sizes of an orifice and cavity, and the selection of piezoelectric diaphragm.

The study helps in establishing a flow control device for controlling flow separation, especially on airfoils.

Design the synthetic jet actuators based on piezoelectric diaphragm for applications of flow separation control.

The purpose of this paper is to describe a procedure to simulate impact-driven liquid jets by computational fluid dynamics (CFD). The proposed CFD model is used to investigate nozzle flow behavior under ultra-high injection pressure and jet velocities generated by the impact driven method (IDM).

A CFD technique was employed to simulate the jet generation process. The injection process was simulated by using a two-phase flow mixture model, while the projectile motion was modeled the moving mesh technique. CFD results were compared with experimental results from jets generated by the IDM.

The paper provides a procedure to simulate impact-driven liquid jets by CFD. The validation shows reasonable agreement to previous experimental results. The pressure fluctuations inside the nozzle cavity strongly affect the liquid jet formation. The average jet velocity and the injection pressure depends mainly on the impact momentum and the volume of liquid in the nozzle, while the nozzle flow behavior (pressure fluctuation) depends mainly on the liquid volume and the impact velocity.

Results may slightly deviate from the actual phenomena due to two assumptions which are the liquid compressibility depends only on the rate of change of pressure respected to the liquid volume and the super cavitation process in the generation process is not taken into account.

Results from this study will be useful for further designs of the nozzle and impact conditions for applications of jet cutting, jet penetration, needle free injection, or any related areas.

This study presents the first success of employing a commercial code with additional user defined function to calculate the complex phenomena in the nozzle flow and jet injection generated by the IDM.

The purpose of this study is to compare two unsteady actuators: an oscillator and a sweeping jet. Both actuators can produce an oscillating jet of different amplitudes and frequencies without any moving parts, making them an attractive actuator concept. The Coanda effect phenomenon can explain the operating principles of these two unsteady actuators.

A numerical study was conducted to compare the amplitudes and frequencies of fluidic and sweeping jet (SJ) oscillators to obtain an efficient actuator to control separated flows at high Reynolds numbers. For this goal, two-dimensional unsteady Reynolds-averaged Navier-Stokes simulations were carried out using computational fluid dynamics (CFD) fluent code to evaluate the actuator performances. The discrete fast Fourier transform method determined the oscillation frequencies.

The oscillation frequencies gradually increase as the inlet pressure increases. The characteristics and dimensions of the vortices produced in the mixing chamber and feedback loops vary overtime when the injected fluid is swept sideways. The frequencies supplied by the SJ are stronger than those obtained by the fluidic oscillator, which may contribute to improving the aerodynamic performance at a lower power supply cost.

The existence of the splitter in the fluidic oscillator led to the production of separate pulses, which would be useful in various industrial applications, including active control of combustion and mixing processes while other applications such as flow separation control require SJs. With the latter actuator higher and interesting frequencies can be obtained, leading to efficient flow control.

The purpose of this research is to study and investigate the flow control of 0.8 Mach jet using three tab configurations. The tabs with the slots will eventually lead to generation of vortices and thus enhances the mixing characteristics.

The jet flow control is achieved by the usage of three tabs, namely, Tab A, Tab B and Tab C that are placed at the exit plane of the convergent nozzle at 180 degrees apart. Three tabs with different slot profile are designed with the same constant blockage ratio of 7.3%. The tabs produce vortices of varying sizes that directly influence and modify the jet structure, thereby enhancing the efficiency in mass entrainment and mixing. The tabs are studied numerically first and then are compared with the results of the experiments.

The results are compared with that of the results of the uncontrolled jet. For Mach 0.8 jet, Tab C is found to reduce the core length and gives reduction of 90.23%, in comparison to Tab A and Tab B, which provides 84.1% and 87.79%, respectively. The results of numerical are then compared with the centerline results obtained via experiments. With the engagement of Tabs A, B and C, the jet structure is seen to have been modified at Mach 0.8 with Tab C performing better.

The tabs are a passive control device that can be practically enabled in the aircraft nozzles to control the flow and even suppress the noise emanated by the jet. Tabs can be effectively used for better thrust vector control and assist in jet noise suppression. Thus, this study on tabs and its uses are important and essential in aerospace technology.

This particular study on mechanical slotted tabs is innovatively carried out by designing the tabs in such a way that one such has not been designed before. The slots run through the adjacent sides of the tabs which is a novelty in itself, whereas perforations made only through the opposite sides of the tabs are studied by various researchers till now. The slots in the adjacent faces modify the flow physics in such a way that it enhances mixing by the creation of turbulence because of the interaction between the main stream and the secondary jet exactly at the core. So far, such slots and profiles are not investigated. By the usage of such tabs, the flow to mix faster is much closer to the core of the jet by creating mixed size vortices and thus has higher efficiency.