Search results

The purpose of this paper is to examine a new idea of vibration control which minimizes joint‐torques and suppresses vibration of the flexible redundant manipulator.

Using the kinematics redundancy feature of the flexible redundant manipulator, the self‐motion in the joint space can be properly chosen to both suppress vibration and minimize joint‐torques.

The study shows that the flexible redundant manipulator still has the second optimization feature on the premise of vibration suppression. The second optimization feature can be used to minimize joint‐torques on the premise of vibration suppression.

To a flexible redundant manipulator, its joint‐torques and vibration can be reduced simultaneously via its kinematics redundancy feature.

The method and algorithm discussed in the paper can be used to minimize joint‐torques and suppress vibration for the flexible redundant manipulator.

The paper contributes to the study on improving dynamic performance of the flexible redundant manipulator via its kinematics redundancy feature. The second optimization capability of the flexible redundant manipulator is discovered and used to both minimize joint‐torques and suppress vibration.

The purpose of this paper is to study the controller design of flexible manipulator. Flexible manipulator system is a nonlinear, strong coupling, time-varying system, which is introduced elastodynamics in the study and complicated to control. However, due to the flexible manipulator, system has a significant advantage in response speed, control accuracy and load weight ratio to attract a lot of researchers.

Since the order of flexible manipulator system is high, designing controller process will be complex, and have a large amount of calculation, but this paper will use the dynamic surface control method to solve this problem.

Dynamic surface control method as a controller design method which can effectively solve the problem with the system contains nonlinear and reduced design complexity.

The authors assume that the dynamic parameters of flexible manipulator system are unknown, and use Radial Basis Function neural network to approach the unknown system, combined with the dynamic surface control method to design the controller.

The purpose of this paper is to present a new method to establish a kinematic model for a continuum manipulator, whose end can be controlled to move in a three-dimensional workspace. A continuum manipulator has significant advantages over traditional, rigid manipulators in many applications because of its ability to conform to the environment. Moreover, because of its excellent flexibility, light weight, low energy consumption, low production cost, it has a number of potential applications in areas of earthquake relief, agricultural harvesting, medical facilities and space exploration.

This paper uses basic theory of material mechanics to deduct motion equations of the manipulator. Unlike other published papers, the manipulator is not based on segments tactics, but regarded as an integrated flexible system, which simplifies its kinematics modelling and motion controlling. The workspace of the manipulator is analysed by theoretical deducing and simulation modelling. For verification of the presented theory, simulation based on ADAMS software was implemented, while a prototype of the manipulator was developed. Both the software simulation and prototype experiment show that the theoretical analysis in this paper is reasonable. The manipulator can move accurately along the desired trajectories.

This paper developed a novel and fully continuous manipulator driven by steel wires. A kinematic model of the manipulator was established. The physical manipulator developed for verifying the kinematic model can effectively track the prescribed trajectory. The presented kinematic model agrees with not only the simulation but also with the experiment.

The manipulator presented in this paper is constructed by steel wires. It possesses the advantages of structural continuity, high flexibility and low production cost. It can be extensively used in many fields, such as search and rescue robotic systems. The limitation of this research is that the dynamic model of the manipulator is not yet clear, which is one of the directions for future research.

The manipulator breaks through the limitation of the joint-type or flexible-link-type manipulator, which can also be extensively used in many fields such as search and rescue robotic systems.

The manipulator developed in this paper, currently, is a prototype under the project of “Automatic Picking Manipulator Research”. It possesses a good market value.

The value of this research is that the manipulator breaks through the limitation of the joint-type or flexible-link-type manipulator and establishes the kinematic model for a fully continuous manipulator by a simple strategy. This is the first study that uses such a strategy for establishing the motion equations of a monolithic continuum manipulator.

Manipulator motion accuracy is a fundamental requirement for precision manufacturing equipment. Light weight manipulators in high speed motions are vulnerable to deformations. The purpose of this work is to analyze the effect of link deformation on the motion precision of parallel manipulators.

The flexible dynamics model of the links is first established by applying the Euler–Bernoulli beam theory and the assumed modal method. The rigid-flexible coupling equations of the parallel mechanism are further derived by using the Lagrange multiplier approach. The elastic energy resulting from spiral motion and link deformations are computed and analyzed. Motion errors of the 3-link torque-prismatic-torque parallel manipulator are then evaluated based on its inverse kinematics. The validation experiments are also conducted to verify the numerical results.

The lateral deformation and axial deformation are largest at the middle of the driven links. The axial deformation at the middle of the driven link is approximately one-tenth of the transversal deformation. However, the elastic potential energy of the transversal deformation is much smaller than the elastic force generated from axial deformation.

Knowledge on the relationship between link deformation and motion precision is useful in the design of parallel manipulators for high performing dynamic responses.

This work establishes the relationship between motion precision and the amount of link deformation in parallel manipulators.

This paper aims to develop a robot for tightening charged bolt to solve the shortcomings of high labor intensity, low efficiency, high risk and poor reliability in artificially tightening drainage board bolt of strain clamp for high voltage transmission line. Realizing bolt-nut capture and location by manipulator is a critical process to complete the whole working task. To solve such key technology, an autonomous location control method for N-joint robot manipulator based on kinematics was proposed.

Through D-H kinematics analysis under flexible working environment of transmission line, the autonomous location control of double manipulators can be abstracted as a nonlinear approximation problem based on joint inverse kinematics. In addition, regarding the complex coupling relationship among different joint angles and the complex decoupling process which leads to the non-uniqueness of inverse solution, an improved backpropagation (BP) network was proposed based on the combination of dynamic adaptive adjustment of learning rate and variable momentum factor, so that the inverse kinematics of manipulator can be solved and the optimization evaluation mechanism of inverse solution can be presented. The proposed autonomous location control method is of adaptability to flexible environment and structural parameters of different drainage boards. The simulation results verified the effectiveness of the proposed method. Compared with the other location control, this method can achieve faster location speed, higher precision and lower hardware cost. Finally, the field operation test further validated that such autonomous location control method was of strong engineering practicability.

The proposed autonomous location control method is adaptable to a flexible environment and to the structural parameters of different types of drainage board. Simulation results confirm the effectiveness of the proposed method, which, in comparison with other approaches to location control, can achieve faster location, higher precision and lower hardware cost. Finally, a field test further confirms the engineering practicability of the proposed autonomous location control method.

The proposed method can achieve faster location speed, higher precision which meet the requirement of real-time control relative to the standard BP algorithm. Moreover, it is of strong adaptability to flexible environment and structural parameters for different drainage board. Field operation experiment further validated the engineering practicability of the method.

Manipulators are often subjected to joint flexibility caused by various causes in industrial applications, such as shaft windup, harmonic drives and bearing deformation. However, many industrial robots are only equipped with motor-side encoders because link-side encoders and torque transducers are expensive. Because of joint flexibility and resulted slow response rate, control performance of these manipulators is very limited. Based on this, the purpose of this paper is to use easy-to-install and cheap accelerometers to improve control performance of such manipulators.

First, a novel tip-acceleration feedback method is proposed to avoid amplifications of approximation errors caused by inversion of the Jacobian matrix. Then, a new control scheme, consisting an artificial neural network, a proportional-derivative (PD) controller and a reference model, is proposed to track motor-side position and suppress link-side vibration.

By using the proposed tip-acceleration feedback method, each link’s vibration can be suppressed correlatively. Through the networks, smaller motor-side tracking errors can be obtained and unknown dynamics can be compensated. Tracking and convergence performance of the network-based system can be improved by using the additional PD controller.

The originality is based on using accelerometers to improve link-side vibration suppression and control performance of flexible-joint manipulators. The previously used methods need expensive link-side sensors or accurate robot model, which is unavailable for many industrial robots only equipped with motor-side encoders. The report proposed a novel acceleration feedback method and used networks to solve such problems.

The purpose of this paper is to propose an efficient and straightforward approach for system identification of a rotating single link flexible manipulator (RSLFM). Also, the achieved results are experimentally validated through identification procedure.

The proposed system identification approach is applied to a RSLFM with a tip mass. At first, the dynamic model of the system is derived using Lagrange method. Then, an efficient method is developed for identification of such a system. This method facilitates the nonlinear complicated identification problem of the RSLFM to a simplified root finding problem.

The main advantage of the developed method is to convert a complicated system identification process to a simple nonlinear equation solution. This approach uses small-size input/output data set and requires a short-time interval of data acquisition, which gives important advantages in lower computational load and lower execution time. The investigated approach is studied on experimental system identification of a single link flexible manipulator. To demonstrate this fact, the developed method is successfully applied in identification of two other mechanical systems; the inverted pendulum on a cart and the ball and beam apparatus.

In this work, the proposed identification approach has been originally applied to a RSLFM and two other mechanical examples. All obtained identification results show the performance and applicability of the developed method clearly. This approach is not restricted in using state space or transfer function. It has significant superiority in comparison with other known approaches including autoregressive with exogenous input (ARX) and Box-Jenkins (BJ).

There is an increasing popularity for the continuum robot in minimally invasive surgery owing to its compliance and dexterity. However, the dexterity takes the challenges in loading and precise control because of the absence of the shape tracking for the continuum robot. The purpose of this paper is to propose a new type of continuum manipulator with variable stiffness that can track the bending shape timely.

The low-melting-point alloy (LMPA) is used to implement the stiffness variation and shape detection for the continuum manipulator. A conceptual design for a single module is presented, and the principle of stiffness control based on the established static model is formulated. Afterward, a shape detection method is introduced in which the shape of the continuum manipulator can be detected by measuring the resistance of every LMPA. Finally, the effect of the proposed variable stiffness method is verified by simulation; the variable stiffness and shape detection methods are evaluated by experiments.

The results from the simulations and experiments indicate that the designed continuum manipulator has the ability of stiffness variation over 42.3% and the shape detection method has high precision.

Compared with conventional structures, the novel manipulator has a simpler structure and integrates the stiffness variation and shape detection capabilities with the LMPA. The proposed method is promising, and it can be conveniently extended to other continuum manipulators.

The development of a generic flexible assembly system involves the design, selection and integration of a number of different mechanical systems in order to develop an assembly system, which is capable of assembling a wide variety of products having an unknown specification. A specific system configuration being dependent on a variety of factors such as, product size, weight, component insertion direction, and manipulator geometry. This paper examines each of the factors that should be considered when designing a generic flexible assembly system and presents a novel generic flexible assembly system design.

The purpose of this paper is to introduce a development and error modeling of a serial redundant manipulator system applied in nuclear fusion environment. Detailed mechanical design of vacuum-compatible arms and actuators are presented, and manipulator flexibility is studied through experiments and model identification algorithm to evaluate the deformation.

First, the manipulator is designed to be several modular segments to obtain enough and flexible workspace inside the fusion device with narrow and complex geometries. Joint actuators with “rotation-linear-rotation” chains are developed to provide both huge reduction ratios and vacuum sealing. The redundant manipulator system has 11 degree of freedoms in total with a storage cask system to dock with the device vacuum vessel. In addition, to improve the position accuracy, an error prediction model is built based on the experimental study and back-propagation neural network (BPNN) algorithm.

Currently, the implementation of the manipulator system has been successfully carried out in both atmosphere and vacuum condition. Excellent performance indicates that the mechanical design is suitable. The validation of BPNN model shows an acceptable prediction accuracy (94∼98 per cent) compared with the real measurement.

This is a special robot system which is practically used in a nuclear fusion device in China. It will allow remote inspection and maintenance of plasma facing components in the vacuum vessel of fusion device without breaking the ultra-high vacuum condition during physical experiments. Its design, mechanism and error prediction strategy have great reference values to the similar robots in vacuum and temperature applications.