Search results

The purpose of this study is to numerically and experimentally investigate the natural convection heat transfer in flat plates and plates with square, trapezoidal and triangular corrugations.

This work is an extension of the previous studies by Verderio et al. (2021a, 2021b, 2021c, 2021d, 2022a). An experimental apparatus was built to measure the plates’ temperatures during the natural convection cooling process. Several physical parameters were evaluated through the experimental methodology. Free and open-source computational tools were used to simulate the experimental conditions and to quantitatively and qualitatively evaluate the thermal plume characteristics over the plates.

The numerical results were experimentally validated with reasonable accuracy in the range of studied RaLP for the different plates. Empirical correlations of Nu¯LPexp=f(RaLP), h¯conv=f(RaLP) and Nu¯LPexp⋅(A/AP)=f(RaLP), with good accuracy and statistical representativeness, were obtained for the studied geometries. The convective thermal efficiency of corrugated plates (Δη), as a function of RaLP, was also experimentally studied quantitatively. In agreement with the findings of Oosthuizen and Garrett (2001), the experimental and numerical results proved that the increase in the heat exchange area of the corrugations has a greater influence on the convective exchange and the thermal efficiency than the disturbances caused in the flow (which reduce h¯conv). The plate with trapezoidal corrugations presented the highest convective thermal efficiency, followed by the plates with square and triangular corrugations. It was also proved that the thermal efficiency of corrugated plates increases with RaLP.

The results demonstrate that corrugated surfaces have greater thermal efficiency than flat plates in heating and/or cooling systems by natural convection. This way, corrugated plates can reduce the dependence on auxiliary forced convection systems, with application in technological areas and Industry 4.0.

The empirical correlations obtained for the corrected Nusselt number and thermal efficiency for the corrugated plate geometries studied are original and unpublished, as well as the experimental validation of the developed three-dimensional numerical code.

Gives a bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore aims to give the reader an encyclopaedic view on the subject. The bibliography at the end of the paper contains 2,025 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1992‐1995.

The problems of transient natural convection from a corrugated plate embedded in an enclosed porous medium is studied numerically. The non‐Darcian effects as well as the acceleration terms are taken into consideration in the momentum equation. The governing equations in terms of vorticity, stream function and temperature are expressed in a body‐fitted coordinates system, which were solved numerically by the finite difference method. Results are presented in terms of streamlines and isotherms, local and average Nusselt numbers, with Darcy‐Rayleigh number ranging from 0 to 1000, and Darcy number from 10^–4 to 10^–1, for several aspect ratios of the cavity and plate positions. The flow and heat transfer characteristics for a corrugated plate and a flat plate and the numerical results solved with four different mathematical models are also compared.

The analysis of ancient buildings presents professionals with important challenges, so it is necessary to have a rational methodology of analysis of these constructions. From the point of view of the technology of structures it is imperative to know the mechanical characteristics of the structural elements involved, as well as the existing stress levels. Currently the tendency is to obtain such knowledge in a non‐destructive way, producing minimal damage. The purpose of this paper is to provide a vision of some of the minor‐destructive techniques (MDT) applied to the diagnosis of historical rubble stone masonry structures.

The paper focuses attention on the employment of techniques based on mechanical stress aspects: flat jack, hole‐drilling and dilatometer, conducted on rubble stone masonry structures. Several computational models were made of parts of the building. These models were used to obtain experimental data (modulus of elasticity and Poisson's ratio). The accuracy of the models was contrasted through the comparison with compression stress levels obtained experimentally.

The paper provides a brief description of these MDT, and exposes the flat jack tests results obtained on several historical masonry walls in the Major Seminary of Comillas (Spain): Compression stress levels, modulus of elasticity and Poisson's ratio of several masonries of this building.

These techniques improve the computational models of constructions, because they can obtain a better knowledge of their mechanical properties, from experimental ways, and the calibration of models through experimental data.

This paper describes one of the first applications of these techniques in Spain.

The purpose of this paper is to examine the velocity and temperature profile for a two-dimensional flow of single- and multi-walled nanotubes (CNTs)/H₂O nanofluid over a flat porous plate, under the impact of non-uniform heat sink/source and radiation. The influence of suction/blowing, viscous dissipation and magnetic field is also incorporated.

The solution of the PDEs describing the flow of nanofluid is accomplished using Runge–Kutta–Fehlberg approach with shooting scheme.

Quantities of physical importance such as local Nusselt number and skin friction coefficient for both types of nanotubes are computed and shown in tables. Also, the impact of copious factors like Prandtl number, magnetic field, Eckert number, porosity parameter, radiation parameter, non-linear stretching parameter, injection/suction, heating variable, particle volume fraction and non-uniform heat sink/source parameter on temperature and velocity profile is explained in detail with the aid of graphs.

Till date, no study has been reported that examines the role of radiation and non-uniform heat sink/source on MHD flow of CNTs‒water nanofluid over a porous plate. The numerical outcomes attained for the existing work are original and their originality is authenticated by comparing them with earlier published work. This problem is of importance, as there are many applications of the fluid flowing over a flat porous plate.

The purpose of this paper is to explore the flow and heat transfer characteristics of the jet impingement onto a conical heat sink and evaluate the ability of heat transfer enhancement.

A numerical study of the flow and heat transfer of liquid impingement on cone heat sinks was conducted, and transition SST turbulence model was validated and adopted. The flow and thermal performances were investigated with the Reynolds number that ranges from 5,000 to 23,000 and cone angle that ranges from 0° to 70° in four regions.

Local Nusselt numbers are large, and pressure coefficients drop rapidly near the stagnation point. In the conical bottom edge, a secondary inclined jet was observed, thereby introducing a horseshoe vortex that causes drastic fluctuations in the curves of the flow and heat transfer. The average Nusselt numbers are higher in a conical protuberance than in flat plates in most cases, thus indicating that the heat transfer performance of jet impingement can be improved by a cone heat sink. The maximum increase is 13.6 per cent when the cone angle is 60°, and the Reynolds number is 23,000.

The flow and heat transfer behavior at the bottom edge of the cone heat sink is supplemented. The average heat transfer capacity of different heat transfer radii was evaluated, which provided a basis for the study of cone arrays.

This paper aims to analyze the additive manufacturing orientation effect of laser sintered polyamide 12 (PA 12) optically translucent parts.

Plates with small features, wedges and lithophanes were laser sintered on a SinterStation HiQ™ in different orientations using PA 12. Lithophane performance was assessed using a Picker 240050 X-ray view/light box. All parts were examined using stereomicroscopy to capture the small features.

The quality of the lithophane image was substantially improved by orienting the flat plate side to the incident backlit light. Sintering in the ZX/ZY plane significantly increased the contrast and resolution compared to sintering in the XY plane. The thinnest feature thickness possible in the SinterStation HiQ is in the XY plane 0.13 mm, and it is 0.57 mm when manufacturing in the ZX/ZY plane.

The laser spot size and other machine parameters were not changeable, which limited the manufacturing resolution. Oblique, non-orthogonal orientations were not investigated.

This is a first effort to investigate the manufacturing orientation effect of laser sintered polyamide optically translucent parts. The manufacturing resolutions on different planes were defined.

A bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view is given. The bibliography at the end of the paper contains 1,726 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1996‐1999.

The purpose of this paper is to study and analyze the effect of roughness and magnetic fluid lubricant on the performance of the squeeze film formed when the upper plate with a porous facing approaches an impermeable and flat lower plate by considering the rotation of the plates.

The roughness of the bearing surface is modeled by a stochastic random variable with non‐zero mean, variance and skewness. The associated Reynolds' equation is stochastically averaged with respect to the random roughness parameter. Results for bearing performance characteristics such as load‐carrying capacity and response time for various values of mean, standard deviation and measure of symmetry are numerically computed. The results are presented graphically as well as in tabular form.

It is observed that the bearing suffers owing to the transverse surface roughness. However, negatively skewed roughness may enhance the performance of the bearing system for suitable values of variance. It is also seen that rotation decreases the load‐carrying capacity but it has marginal influence in the presence of the magnetic fluid. Further, the performance of the bearing system registers a steady improvement with the increasing values of the magnetization parameter. In addition, the response time follows the trends of the load‐carrying capacity.

The originality of the paper lies in the fact that the roughness must be accounted for while designing the bearing system, even though a suitable rotation ratio parameter is chosen in the presence of a strong magnetic fluid. Of course, the best performance of the bearing system is registered in the case of negatively skewed roughness.

In this study, the effects of using corrugated absorber plate (instead of flat plate) and also using aerosol/carbon-black nanofluid (instead of air) on heat transfer and turbulent flow characteristics in solar collectors were numerically investigated.

The 3D continuity, momentum and energy equation were solved by finite volume and SIMPLE algorithm. As a result, the corrugated absorber plate was inspected in the case of triangle, rectangle and sinuous with the wave length of 1 mm and wave amplitude of 3 mm in turbulent flow regime and Reynolds number between 2,500 and 4,000. Choosing the proper geometry was carried out based on the best performance evaluation criteria (PEC) and increasing the air temperature from collector inlet to outlet.

The results revealed that for all times of the year the highest PEC was obtained for corrugated Sinusoidal model; however, the highest temperature increase from inlet to outlet was obtained for rectangular corrugated model. In addition, the results indicated that in sinusoidal model, the nanoparticles volume fractions increase leads to heat performance coefficient increase and the best heat performance conditions were attained in volume fraction of 0.1 per cent and Reynolds number of 4,000 for both six months period. In model with rectangular corrugated plate, usage of nanofluid in all range of Reynolds numbers leads to reduction of outlet temperature.

The effect of some nanoparticles on heat transfer using thermal– hydraulic performances in heat exchangers has been assessed, but the effects of atmospheric aerosol-based nanofluid using carbon-black nanoparticles (CBNPs) on the heat transfer in corrugated heat sink solar collectors by 3D numerical modeling has not been yet investigated. In present study, usage of CBNPs with different volume fractions in range of 0 to 0.1 per cent in turbulent regime of fluid flow is analyzed. Furthermore, in this paper, besides the effects of using CBNPs, a solar absorber located in Shiraz, as one of the best solar irradiation receiver cities in Iran is evaluated.