Search results

The purpose of this paper is to investigate the tensile strength, Young’s modulus, dimensional stability and porosity of acrylonitrile butadiene styrene (ABS)–oil palm fiber composite filament for fused deposition modeling (FDM).

A new feedstock material for FDM comprising oil palm fiber and ABS as a matrix was developed by a twin screw extruder. The composite filament contains 0, 3, 5 and 7 Wt.% of oil palm fiber in the ABS matrix. The tensile test is then performed on the fiber composite filament, and the wire diameter is measured. In this study, the Archimedes method was used to determine the density and the porosity of the filament. The outer surface of the wire composite was examined using an optical microscope, and the analysis of variance was used to assess the significance and the relative relevance of the primary factor.

The results showed that increasing the fiber loading from 0.15 to 0.4 MPa enhanced tensile strength by 60%. Then, from 16.1 to 18.3 MPa, the Young’s modulus rose by 22.8%. The density of extruded filament decreased and the percentage of porosity increased when the fiber loading was increased from 3 to 7 Wt.%. The diameter deviation of the extruded filaments varied from −0.21 to 0.04 mm.

This paper highlights a novel natural resource-based feedstock material for FDM. Its mechanical and physical properties were also discovered.

With the popularization of electronic products, the electromagnetic radiation pollution has been the fourth largest pollution after water, air and noise pollution. Therefore, electromagnetic shielding property of textiles is attracting more attention. In this paper, the properties of electromagnetic shielding yarns and fabrics were studied.

Ten kinds of yarn, stainless steel short fiber and polyester blend yarn with three different blending ratios T/S 90/10, T/S 80/20 and T/S 70/30, stainless steel short fiber, polyester and cotton blend yarn with blending ratio C/T/S 35/35/30, core-spun yarn with one 30 um stainless steel filament C/T28tex/S(30 um), core-spun yarn with two 15 um stainless steel filaments (C/T28tex/S(15 um)/S(15 um)), twin-core-spun yarn with one 30 um stainless steel filament and one 50D spandex filament C/T28tex/S(30 um)/SP(50D), sirofil wrapped yarn with one 30 um stainless steel filament feeding from left S(30 um)+C/T28tex, sirofil wrapped yarn with one 30 um stainless steel filament feeding from right C/T28tex+S(30 um), sirofil wrapped yarn with two 15 um stainless steel filaments feeding from two sides S(15 um)+C/T28tex+ S(15 um), were spun. The qualities of spun yarns were measured. Then, for analyzing the electromagnetic shielding properties of fabrics made of different spun yarns, 20 kinds of fabrics were woven.

The tested results show that comparing to the T/S 80/20 blend yarn, the resistivity of composite yarns with the same ratio of the stainless steel filament is smaller. The possible reason is that comparing to the stainless steel short fiber, the conductivity of stainless steel filament is better because of the continuous distribution of stainless steel in the filament. Comparing with the core-spun yarn, the conductivity of the sirofil wrapped yarn is a little better. Comparing to the fabric woven by the blend yarn, the electromagnetic shielding of the fabric woven by the composite yarn is better, and comparing to the fabric woven by the core-spun yarn, the electromagnetic shielding of the fabric woven by the sirofil yarn is a little better. The possible reason is that the conduction network can be produced by the stainless steel filament wrapped on the staple fiber yarn surface in the fabric, and the electromagnetic wave can be transmitted in the network.

In this paper, the properties of electromagnetic shielding yarns and fabrics were studied. Ten kinds of yarn, including three stainless steel short fiber and polyester blend yarns, one stainless steel short fiber, polyester and cotton blend yarn, two core-spun yarns, one twin-core-spun yarn, three sirofil wrapped yarn, were spun. Then, for analyzing the electromagnetic shielding properties of fabrics made of different spun yarns, 20 kinds of fabrics were woven. The effects of fabric warp and weft densities, fabric structures, yarn kinds, yarn distributions in the fabric on electromagnetic shielding were analyzed.

This study/paper aims to develop fundamental understanding of mechanical properties for multiple fibre-reinforced materials by using a single-filament-wide tensile-testing approach.

In this study, recently validated single-filament-wide tensile-testing specimens were used for four polymers with and without short-fibre reinforcement. Critically, this specimen construct facilitates filament orientation control, for representative longitudinal and transverse composite directions, and enables measurement of interlayer bonded area, which is impossible with “slicing” software but essential in effective property measurement. Tensile properties were studied along the direction of extruded filaments (F) and normal to the interlayer bond (Z) both experimentally and theoretically via the Kelly–Tyson model, bridging model and Halpin–Tsai model.

Even though the four matrix-material properties varied hugely (1,440% difference in ductility), consistent material-independent trends were identified when adding fibres: ductility reduced in both F- and Z-directions; stiffness and strength increased in F but decreased or remained similar in Z; Z:F strength anisotropy and stiffness anisotropy ratios increased. Z:F strain-at-break anisotropy ratio decreased; stiffness and strain-at-break anisotropy were most affected by changes to F properties, whereas strength anisotropy was most affected by changes to Z properties.

To the best of the authors’ knowledge, this is the first study to assess interlayer bond strength of composite materials based on measured interlayer bond areas, and consistent fibre-induced properties and anisotropy were found. The results demonstrate the critical influence of mesostructure and microstructure for three-dimensional printed composites. The authors encourage future studies to use specimens with a similar level of control to eliminate structural defects (inter-filament voids and non-uniform filament orientation).

With the improvement of living standards and acceleration of working pace, the shape retention property of textiles has attracted more attention. Yarn spinning is the first fundamental process in making textiles and apparel, and the properties of yarn influence the performance of textiles directly. Filament/staple fiber composite yarn is a kind of yarn spun by filament and staple fiber, and comprehensive qualities of yarn can be improved. Therefore, the purpose of this paper is to study the shape retention properties of filament/staple fiber composite yarns and corresponding fabrics.

Four kinds of composite yarn, core-spun yarn with one 50D SPH filament feeding, sirofil wrapped yarn with one 50D SPH filament feeding from left, sirofil wrapped yarn with one 50D SPH filament feeding from right, sirofil wrapped yarn with two 25D SPH filaments feeding from two sides, were spun. The qualities of spun yarns were measured. Then, corresponding two kinds of twill fabrics were woven by core-spun yarn and sirofil wrapped yarn with two filaments, respectively. The handle parameters, crease recovery, appearance leveling after washing, dimensional change rate after washing, strength and elongation and tensile elasticity were tested by using corresponding test instruments.

The tested results of spun yarn qualities show that comparing with the core-spun yarn, the evenness of sirofil wrapped yarn is improved, the hairiness is reduced, and the breaking strength and elongation are increased. Comparing with sirofil wrapped yarn with one filament, the evenness of sirofil wrapped yarn with two filaments is improved. The measured results of fabrics properties show that under the same weaving process, comparing to the fabric woven by core-spun yarn, the dimension of fabric woven by sirofil wrapped yarn is small after desizing, and warp and weft density is large. The possible reason is that the shrinkage of the SPH filament outside the sirofil wrapped yarn happens after desizing, which also makes the dimensional change rate after washing of the corresponding fabric large, and crease recovery poor.

In the paper, for improving the shape retention properties of the pure cotton woven fabric, one kind of SPH filament was added to the woven fabric by spinning filament/staple fiber composite yarns. Four kinds of composite yarn, core-spun yarn with one 50D SPH filament, sirofil wrapped yarn with one 50D SPH filament feeding from the left side, sirofil wrapped yarn with one 50D SPH filament feeding from the right side, sirofil wrapped yarn with two 25D SPH filaments feeding from two sides, were spun. Two kinds of twill fabrics were weaving by core-spun yarn and sirofil wrapped yarn with two filaments, respectively.

The purpose of this paper is to investigate the factors governing bond strength in fused deposition modeling (FDM) compared to strength in the fiber direction.

Acrylonitrile butadiene styrene (ABS) boxes with the thickness of a single fiber were made at different platform and nozzle temperatures, print speeds, fiber widths and layer heights to produce multiple specimens for measuring the strength.

Specimens produced with the fibers oriented in the tensile direction had 95 per cent of the strength of the constitutive filament. Bond strengths ranged from 40 to 85 per cent of the filament strength dependent on the FDM processing conditions. Diffusion, wetting and intimate contact all separately affect bond strength.

This study provides processing recommendations for producing the strongest FDM parts. The needs for higher nozzle temperatures and more robust feed motors are described; these recommendations can be useful for companies producing FDM products as well as companies designing FDM printers.

This is the first study that discusses wetting and intimate contact separately in FDM, and the results suggest that a fundamental, non-empirical model for predicting FDM bond strength can be developed based on healing models. Additionally, the role of equilibration time at the start of extrusion as well as a motor torque limitation while trying to print at high speeds are described.

The limited strength of polylactic acid (PLA) hinders its extensive engineering applications. This paper aims to enhance its strength and realize diverse applications.

Here, the continuous fiber reinforced PLA composites are fabricated by a customized fused filament fabrication three-dimensional printer. Uniaxial tensile and three-point flexural tests have been conducted to analyze the reinforcement effect of the proposed composites. To unveil the adhering mechanism of optic fiber (OF) and PLA, post failure analysis including the micro imaging and morphology have been performed. The underlying mechanism is that the axial tensile strength of the OF and the interfacial adhesion between PLA and OF compete to enhance the mechanical properties of the composite.

It is found that 10%–20% enhancement of strength, ductility and toughness due to the incorporation of the continuous OF.

The continuous OFs are put into PLA first time to improve the strength. The fabrication method and process reported here are potentially applied in such engineering applications as aerospace, defense, auto, medicine, etc.

In industry, fused filament fabrication (FFF) offers flexibility and agility by promoting a reduction in costs and in the lead-time (i.e. time-to-market). Nevertheless, FFF parts exhibit some limitations such as lack of accuracy and/or lower mechanical performance. As a result, some alternatives have been developed to overcome some of these restrictions, namely, the formulation of high performance polymers, the creation of fibre-reinforced materials by FFF process and/or the design of new FFF-based technologies for printing composite materials. This work aims to analyze these technologies.

This work aims to study and understand the advances in the behaviour of 3D printed parts with enhanced performance by its reinforcement with several shapes and types of fibres from nanoparticles to continuous fibre roving. Thus, a comprehensive survey of significant research studies carried out regarding FFF of fibre-reinforced thermoplastics is provided, giving emphasis to the most relevant and innovative developments or adaptations undergone at hardware level and/or on the production process of the feedstock.

It is shown that the different types of reinforcement present different challenges for the printing process with different outcomes in the part performance.

This review is focused on joining the most important researches dedicated to the process of FFF-printed parts with different types reinforcing materials. By dividing the reinforcements in categories by shape/geometry and method of processing, it is possible to better quantify performance improvements.

Microfiber is one of the major sources of microplastic emission into the environment. In recent times, research on microfiber has gained momentum, and research across different disciplines was performed. However, no complete study was performed from the viewpoint of textiles to analyse the microfiber shedding behaviour by relating the properties textiles. The purpose of this paper is to analyse the microfiber shedding behaviour in textiles.

Articles on the microfiber shedding across different disciplines were collected and analysed systematically to identify the influencing factor. The influence of laundry parameters is found to be majorly discussed section, yet very few research data is found on the effect of yarn and fabric properties on the microfiber shedding.

Most of the articles listed laundry detergent addition, higher temperature, use of softeners, type of washing machines used and amount of liquid used as the major factors influencing the fiber shedding. Concerning the fiber and yarn characteristics, yarn twist, fiber type (staple/filament), method of production, fabric structure and specific density are reported as influencing factors. Some articles highlighted the influence of ageing of textiles on the fiber shedding.

The review identified the research gap in the textile sector and reports that so far, no research performed on microfiber shedding with the textile parameters. The review further urges the importance of research works to be performed in the textile by considering the fabric and yarn properties.

The purpose of this study is to confirm that the stiffness of fused filament fabrication (FFF) three-dimensionally (3D) printed fiber-reinforced thermoplastic (FRP) materials can be predicted using classical laminate theory (CLT), and to subsequently use the model to demonstrate its potential to improve the mechanical properties of FFF 3D printed parts intended for load-bearing applications.

The porosity and the fiber orientation in specimens printed with carbon fiber reinforced filament were calculated from micro-computed tomography (µCT) images. The infill portion of the sample was modeled using CLT, while the perimeter contour portion was modeled with a rule of mixtures (ROM) approach.

The µCT scan images showed that a low porosity of 0.7 ± 0.1% was achieved, and the fibers were highly oriented in the filament extrusion direction. CLT and ROM were effective analytical models to predict the elastic modulus and Poisson’s ratio of FFF 3D printed FRP laminates.

In this study, the CLT model was only used to predict the properties of flat plates. Once the in-plane properties are known, however, they can be used in a finite element analysis to predict the behavior of plate and shell structures.

By controlling the raster orientation, the mechanical properties of a FFF part can be optimized for the intended application.

Before this study, CLT had not been validated for FFF 3D printed FRPs. CLT can be used to help designers tailor the raster pattern of each layer for specific stiffness requirements.

As one kind of filament/staple fiber composite yarn, core spun yarn has been widely used, especially on Jeans. However, there is only one filament in the commonly used core spun yarn, such as spandex, and the performance of the one filament often is influenced during dyeing and finishing. Therefore, in the paper, twin-core spun yarns with two different filaments feeding simultaneously were spun on ring spinning frame modified by one kind of filament feeding numerical control device. The paper aims to discuss these issues.

Four kinds of twin-core spun yarns, cotton/spandex/PBT, cotton/spandex/CM800, cotton/spandex/T400, cotton/spandex/SPH with linear density 36.4tex/40D/50D were spun. For improving the covering effect of the two filaments, the filament feeding position, filament pre-drafting multiple, distance between two staple roving, designed twist factor of the core spun yarn were optimized.

It is shown that comparing with the core spun yarn, the breaking strength and elongation of the twin-core spun yarns are improved since the addition of another elastic filament, while the evenness is a little worse.

By using the twin-core spun yarns, corresponding knitted and woven fabrics are produced. Meanwhile, for simulating the dyeing and finishing process, the knitted fabrics were treated during the 150°C high temperature. It is shown that comparing with the fabrics produced by cotton/spandex yarn, addition of another elastic filament can improve the fabric strength and resistant and has positive effect on worsen prevention for high temperature treated fabric elastic recovery, and on change prevention during the dyeing and finishing process for fabric handle properties, and improves the fabric stability.