Search results

Results – From a hardening test, we then tested with an impact tester charpy Treviolo H060. The results showed that the impact strength is escalated up to 29.09% post-hardening circle, which was observed using electrical microscope. The value of steel strength increased 2.12 J/mm² compared with earlier hardening process, which is, 1.57 J/mm². The results showed that the fracture in the welding process without the hardening process is a brittle fracture that is shown by the flat crystal structure; on the other hand, the hardening process before welding shows a form of coarse-looking structure indicating that the specimen has an impact towards which the toughness is higher.

Research Limitations/Implications – The effect influence of the hardening process to the impact strength of welded joints before and after the hardening process SMAW AISI 1050 steel hardening process. The mechanical properties test is done with the equipment impact charpy.

Practical Implications – The field we often encounter is erosion or wear out occurring in the construction, for example, many equipments such as agricultural equipment, bridges, ship construction, motor shaft, machining such as hand tools, small rings, and agricultural tools.

Originality/Value – This is the first reported research on impact strength using the hardening test.

The purpose of this paper is to provide a general picture for describing the formed tribofilm, including chemical and physical aspects in the micro-scale and the nano-scale. In a previous study, the durability of zinc dialkyl dithiophosphate (ZDDP) tribofilms on cylinder liner samples has been investigated in a tribometer model system by using fresh and aged fully formulated oils and replacing them with PAO8 without additives. Analyses of the derived tribofilms by means of X-ray photoelectron spectroscopy and scanning electron microscopy could give some hints about the underlying mechanisms of the tribofilm build-up and wear performance, but a final model has not been achieved.

Thus, characterisation of these tribofilms by means of focused ion beam-transmission electron microscopy (FIB-TEM) and energy dispersive X-ray spectroscopy is presented and a concluding model of the underlying mechanisms of tribofilm build-up is discussed in this paper.

For tribotests running first with fresh fully formulated engine oil, a rather homogeneous ZDDP-like tribofilm is found underneath a carbon rich tribofilm after changing to non-additivated PAO8. However, when the tests run first with aged fully formulated engine oil, no ZDDP-like tribofilm has been found after changing to non-additivated PAO8, but a wear protective carbon rich tribofilm.

The obtained results provide insights into the structure and durability of tribofilms. Carbon-based tribofilms are built up on the basis of non-additivated PAO8 because of the previously present ZDDP tribofilms, which suggests an alternative way to reducing the consumption of antiwear additives.

The material extrusion (ME) process induces variations in the final part’s microscopic and macroscopic structural characteristics. This viewpoint article aims to uncover the relation between ME fabrication parameters and the microstructural and mesostructural characteristics of the ME BASF Ultrafuse Steel 316L metal parts. These characteristics can affect the structural integrity of the produced parts and components used in various engineering applications.

Recent studies on the ME BASF Ultrafuse Steel 316L are reviewed, with a focus on those which report microstructural and mesostructural characteristics that may affect structural integrity.

A relationship between ME fabrication parameters and subsequent microstructural and mesostructural characteristics is discussed. Common microstructural and mesostructural/macrostructural defects are also highlighted and discussed.

This viewpoint article attempts to bridge the existing gap in the literature, highlighting the influence of ME fabrication parameters on Steel 316L parts fabricated via this additive manufacturing method. Moreover, this article identifies and discusses important considerations for the purposes of selecting and optimising the structural integrity of ME-fabricated Steel 316L parts.

Molecular dynamics is an emerging simulation technique in the field of machining in recent years. Many researchers have tried to simulate different processing methods of various materials with the theory of molecular dynamics (MD), and some preliminary conclusions have been obtained. However, the application of MD simulation is more limited compared with traditional finite element model (FEM) simulation technique due to the complex modeling approach and long computation time. Therefore, more studies on the MD simulations are required to provide a reliable theoretical basis for the nanoscale interpretation of grinding process. This study investigates the crystal structures, dislocations, force, temperature and subsurface damage (SSD) in the grinding of iron-nickel alloy using MD analysis.

In this study the simulation model is established on the basis of the workpiece and single cubic boron nitride (CBN) grit with embedded atom method and Morse potentials describing the forces and energies between different atoms. The effects of grinding parameters on the material microstructure are studied based on the simulation results.

When CBN grit goes through one of the grains, the arrangement of atoms within the grain will be disordered, but other grains will not be easily deformed due to the protection of the grain boundaries. Higher grinding speed and larger cutting depth can cause greater impact of grit on the atoms, and more body-centered cubic (BCC) structures will be destroyed. The dislocations will appear in grain boundaries due to the rearrangement of atoms in grinding. The increase of grinding speed results in the more transformation from BCC to amorphous structures.

This study is aimed to study the grinding of Fe-Ni alloy (maraging steel) with single grit through MD simulation method, and to reveal the microstructure evolution within the affected range of SSD layer in the workpiece. The simulation model of polycrystalline structure of Fe-Ni maraging steel and grinding process of single CBN grit is constructed based on the Voronoi algorithm. The atomic accumulation, transformation of crystal structures, evolution of dislocations as well as the generation of SSD are discussed according to the simulation results.

This paper aims to investigate the wear behaviour of different materials for cylinder liners and piston rings in a linear reciprocating tribometer with special focus on the wear of the cylinder liner in the boundary lubrication regime.

Conventional nitrided steel, as well as diamond-like carbon and chromium nitride-coated piston rings, were tested against cast iron, AlSi and Fe-coated AlSi cylinder liners. The experiments were carried out with samples produced from original engine parts to have the original surface topography available. Radioactive tracer isotopes were used to measure cylinder liner wear continuously, enabling separation of running-in and steady-state wear.

A ranking of the material pairings with respect to wear behaviour of the cylinder liner was found. Post-test inspection of the cylinder samples by scanning electron microscopy (SEM) revealed differences in the wear mechanisms for the different material combinations. The results show that the running-in and steady-state wear of the liners can be reduced by choosing the appropriate material for the piston ring.

The use of original engine parts in a closely controlled tribometer environment under realistic loading conditions, in conjunction with continuous and highly sensitive wear measurement methods and a detailed SEM analysis of the wear mechanisms, forms an intermediate step between engine testing and laboratory environment testing.