Search results

The purpose of this paper is to determine the ultra-high cycle fatigue behavior and ultra-slow crack propagation behavior of selective laser melting (SLM) AlSi7Mg alloy under as-built conditions.

Constant amplitude and two-step variable amplitude fatigue tests were carried out using ultrasonic fatigue equipment. The fracture surface of the failure specimen was quantitatively analyzed by scanning electron microscope (SEM).

The results show that the competition of surface and interior crack initiation modes leads to a duplex S–N curve. Both manufacturing defects (such as the lack of fusion) and inclusions can act as initially fatal fatigue microcracks, and the fatigue sensitivity level decreases with the location, size and type of the maximum defects.

The research results play a certain role in understanding the ultra-high cycle fatigue behavior of additive manufacturing aluminum alloys. It can provide reference for improving the process parameters of SLM technology.

The purpose of this paper is to present a crack initiation mechanism of the external hydrogen effect on type 304 stainless steel, as well as on fatigue crack propagation in the presence of hydrogen gas.

The effects of external hydrogen on hydrogen-assisted crack initiation in type 304 stainless steel were discussed by performing fatigue crack growth rate and fatigue life tests in 5 MPa argon and hydrogen.

Hydrogen can reduce the incubation period of fatigue crack initiation of smooth fatigue specimens and greatly promote the fatigue crack growth rate during the subsequent fatigue cycle. During the fatigue cycle, hydrogen invades into matrix through the intrusion and extrusion and segregates at the boundaries of α′ martensite and austenite. As the fatigue cycle increased, hydrogen-induced cracks would initiate along the slip bands. The crack initiation progress would greatly accelerate in the presence of hydrogen.

To the best of the authors’ knowledge, this paper is an original work carried out by the authors on the hydrogen environment embrittlement of type 304 stainless steel. The effects of external hydrogen and argon were compared to provide understanding on the hydrogen-assisted crack initiation behaviors during cycle loading.

The study aims to examine the effect of inclusions and inherent microstructure on fatigue behavior of 34Cr2Ni2Mo steel.

Fatigue behavior of 34Cr2Ni2Mo steel was investigated for up to 1E10 cycles.

Results showed that both inclusion and inherent microstructure have an influence on the crack initiation mechanism. Fatigue cracks mostly initiated from inclusions, whereas substrate-induced crack initiations were also observed. Fatigue life of inclusion-induced failures is mostly determined by the location of inclusions rather than the loading stress. The inherent microstructure seems to tolerate inclusions at a lower stress level in very high-cycle regime owing to the absence of internal inclusion-induced failure. For the substrate-induced crack initiations, high-density dislocations are found to be accumulated around the carbide particle-matrix interface, which may be the cause of crack initiation in the inherent structure due to strain localization.

The effect of inclusions and inherent microstructure on fatigue behavior of 34Cr2Ni2Mo steel up to 1E10 cycles.

Highlights

• Fatigue failure occurs even at a lifetime of 5.76E9 cycles.

• Surface inclusion induced premature failures.

• Inherent microstructure tolerates inclusions at lower stress level.

• Internal carbides promote substrate-induced crack initiations.

Fatigue failure occurs even at a lifetime of 5.76E9 cycles.

Surface inclusion induced premature failures.

Inherent microstructure tolerates inclusions at lower stress level.

Internal carbides promote substrate-induced crack initiations.

One of the challenges in the prediction of fatigue crack growth is to identify representative initial flaws and defects that can cause fatigue crack initiation and subsequent crack growth. Representative initial flaws identified from this experimental study provided an essential input for the fatigue life assessment programme of the PC-9/A training aircraft currently in service. The paper aims to discuss these issues.

This paper addresses this challenge with a critical literature review and experimental assessment of initial flaw types that may cause fatigue crack initiation, by fatigue testing and fractography analysis using optical microscope and scanning electron microscopy (SEM).

With a focus on aluminium alloy (AA) 2024-T3 thin sheet, the results cover various discontinuities from microstructural constituent particles inherent from the material process to macrostructural defects and surface discontinuities (such as burrs and machining marks) introduced during the production of airframes. It was found that most fatigue cracks originated from the bore surface discontinuities of rivet holes in the PC-9 vertical stabiliser thin panels rather than microstructural material defects of AA2024-T3 inherent from the material process.

The experimental study has found that quantifying fatigue initial flaw sizes which resulted from poorly finished fastener holes with arbitrary discontinuities at the surface is a challenging topic. This topic is under the current investigation using a statistics based analysis of initial flaws in the prediction of fatigue crack growth.

The results obtained from this experimental study provided an essential input for the empennage and aft fuselage recertification and life assessment programme for the PC-9/A training aircraft currently in service.

This experimental study examined AA2024-T3 thin skin panels from two different PC-9/A aircraft. The post-test failure analysis using optical microscope and SEM found that machining defects dominate fatigue crack initiation that can result in subsequent crack propagation.

This study aims to investigate the fatigue crack propagation behavior of SiC particle-reinforced 2124 Al alloy composites under constant amplitude axial loading at a stress ratio of R = 0.1. For this purpose, it is performed experiments and comparatively analyze the results by producing 5, 10, 15 Vol.% SiCp-reinforced composites and unreinforced 2124 Al alloy billets with powder metallurgy (PM) production technique.

With the PM production technique, SiCp-reinforced composite and unreinforced 2124 Al alloy billets were produced at 5%, 10%, 15% volume ratios. After the produced billets were extruded and 5 mm thick plates were formed, tensile and fatigue crack propagation compact tensile (CT) samples were prepared. Optical microscope examinations were carried out to determine the microstructural properties of billet and samples. To determine the SiC particle–matrix interactions due to the composite microstructure, unlike the Al alloy, which affects the crack initiation life and crack propagation rate, detailed scanning electron microscopy (SEM) studies have been carried out.

Optical microscope examinations for the determination of the microstructural properties of billet and samples showed that although SiC particles were rarely clustered in the Al alloy matrix, they were generally homogeneously dispersed. Fatigue crack propagation rates were determined experimentally. While the highest crack initiation resistance was achieved at 5% SiC volume ratio, the slowest crack propagation rate in the stable crack propagation region was found in the unreinforced 2124 Al alloy. At volume ratios greater than 5%, the number of crack initiation cycles decreases and the propagation rate increases.

As a requirement of damage tolerance design, the fatigue crack propagation rate and fatigue behavior of materials to be used in high-tech vehicles such as aircraft structural parts should be well characterized. Therefore, safer use of these materials in critical structural parts becomes widespread. In this study, besides measuring fatigue crack propagation rates, the mechanisms causing crack acceleration or deceleration were determined by applying detailed SEM examinations.

Many failures of aircraft structural components in the past were attributed to cracks emanating from joints, which are identified as the most critical locations. In cases using the recently emerging structural health monitoring (SHM) systems, continuous monitoring needs be carried out at many major joint locations. The purpose of this paper is to develop computational techniques for fastener joints, including the possible change in contact conditions and change in boundary values at the pin-hole interface. These techniques are used for the prognostic analysis of pin-loaded lug joints with rigid/elastic pin subjected to fatigue loading by estimating the residual life of the component at any given instance to assist the SHM systems.

Straight attachment lug joints with rigid/elastic push-fit pin and smooth pin-hole interface are modelled in commercial software MSC PATRAN. In each case, the joint is subjected to various types of fatigue load cycles, and for each type of cycles, the critical locations and the stress concentrations are identified from the stress analysis. Later, for each type of fatigue cycle, the number of cycles required for crack initiation is estimated. A small crack is located at these points, and the number of cycles required to reach the critical length when unstable crack growth occurs is also computed. The novelty in the analysis of life estimations is that it takes into account possible changes in contact conditions at the pin-hole interface during load reversals in fatigue loading.

The current work on fastener joints brings out the way the load reversals leading to change in contact conditions (consequently changing boundary conditions) are handled during fatigue loading on a push-fit joint. The novel findings are the effect of the size of the hole/lug width, elasticity of the material and the type of load cycles on the fatigue crack initiation and crack growth life. Given other parameters constant, bigger size hole and stiffer pin lead to lesser life. Under load controlled fatigue cycles, pull load contributes to significant part of fatigue life.

The analysis considers the changing contact conditions at the pin-hole interface during fatigue cycles with positive and negative stress ratios. The results presented in this paper are of value to the life prediction of structural joints for various load cycles (for both pull-pull cases, in which the load ratios are positive, and pull-push cycles, where the load ratios are negative). The prognostic data can be used to effectively monitor the critical locations with joints for SHM applications.

Lug joints with fasteners play a crucial role in connecting many major components of the aircraft. Most of the failures in the past were credited to the damages initiating and progressing from these types of joints. Ensuring the structural integrity of these fastener joints is a major issue in many engineering structures, especially in aerospace components, which would otherwise lead to fatal failure. The purpose of this paper is to adopting the prognostic approach for analysing these lug joints with fasteners subjected to off-axis loading by estimating the crack initiation and crack growth life of these joints. This data will be useful to estimate the remaining life of these joints at any given stage of operations, which is mandatory in structural health monitoring (SHM).

Straight and tapered lug joints are modelled using the finite element method in MSC PATRAN and analysed in MSC NASTRAN. These lug joints are analysed with a push fit fastener. The contact/separation regions at the pin–lug interface are carefully monitored throughout the analysis for various loading conditions. Critical locations in these lug joints are identified through stress analysis. Fatigue crack initiation and fatigue crack growth analysed is carried out at these locations for different load ratios. A computational method is proposed to estimate the cycles to reach crack initiation and cycles at which the crack in the lug joint become critical by integrating several known techniques.

Analysis carried out in this paper describes the importance of tapered lug joints, particularly when subjected to non-conventional way of loading, i.e. off-axis loading. There is a partial loss of contact between pin and lug upon pin loading, and this does not change further with monotonically increasing pin load. But during load reversals, there is a change in contact/separation regions which is effectively handled by inequality constraints in the boundary conditions. Crack growth in these lug joints pertains to mixed-mode cracking and is computed through the MVCCI technique.

Most of the earlier works were carried out on in-plane pin loading along the axis of symmetry of the lug. The current work considers the off-axis pin loading by loading the lug joints with transverse and oblique pin load. The significance of taper angle under such loading condition is brought in this paper. The results obtained in this paper through prognostic approach are of direct relevance to the SHM and damage tolerance design approach where the safety of the structural components is of foremost priority.

The purpose of this paper is to determine the corrosion fatigue behavior and mechanism of 6005A aluminum alloy and welded joint.

Electron back-scattered diffraction (EBSD) were adopted to characterize the microstructure of 6005A aluminum alloy and welded joint. Through potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and corrosion fatigue experiments, the corrosion fatigue behavior and mechanism of 6005A aluminum alloy base metal and welded joint were studied.

The results show that the corrosion fatigue crack initiation of 6005A aluminum alloy base metal and welded joint is mainly caused by the preferential anodic dissolution and hydrogen concentration in the areas with inclusions and welding defects.

The research is an originality study on the corrosion fatigue behavior and mechanism of 6005A aluminum alloy and welded joint.

This article aims to investigate and model the effects of welding-generated thermal cycle on the resulting residual stress distribution and its role in the initiation and propagation of fatigue failure in thick shaft sections.

Experimental and numerical techniques were applied in the present study to explore the relationship(s) between welding residual-stress distribution and fatigue failure characteristics in a hydropower generator shaft. Experimental techniques included stereomicroscopy, optical and scanning electron microscopy (SEM), chemical analysis and mechanical testing. Finite element modelling (FEM) was used to model the shaft welding cycle in terms of thermal (temperature) history and the associated development of residual stresses within the weld joint.

Experimental analyses have confirmed the suitability of the used material for the intended application and confirmed the failure mode to be low cycle fatigue. The observed failure characteristics, however, did not match with the applied loading in terms of design stress levels, directionality and expected crack imitation site(s). FEM results have revealed the presence of a sharp stress peak in excess of 630 MPa (about 74% of material's yield strength) around weld start point and a non-uniform residual stress distribution in both the circumferential and through-thickness directions. The present results have shown very close matching between FEM results and observed failure characteristics.

The present article considers an actual industrial case of a hydropower generator shaft failure. Present results are valuable in providing insight information regarding such failures as well as some preventive design and fabrication measures for the hydropower and other power generation and transmission sector.

The presence of the aforementioned stress peak around welding start/end location and the non-uniform distribution of residual-stress field are in contrast to almost all published results based on some uniformity assumptions. The present FEM results were, however, the only stress distribution scenario capable of explaining the failure considered in the present research.

Wind energy is one of the most promising and the fastest growing alternative-energy production technologies, which have been developed in response to stricter environmental regulations, the depletion of fossil-fuel reserves, and the world's ever-growing energy needs. This form of alternative energy is projected to provide 20 percent of the US energy needs by 2030. For economic reasons, wind turbines (articulated structures that convert wind energy into electrical energy) are expected to operate, with only regular maintenance, for at least 20 years. However, some key wind turbine components (especially the gearbox) tend to wear down, malfunction and fail in a significantly shorter time, often three to five years after installation, causing an increase in the wind-energy cost and in the cost of ownership of the wind turbine. Clearly, to overcome this problem, a significant increase in long-term gearbox reliability needs to be achieved.

While purely empirical efforts aimed at identifying shortcomings in the current design of the gearboxes are of critical importance, the present work demonstrates that the use of advanced computational engineering analyses, like the finite-element stress analysis and a post-processing fatigue-life assessment analysis, can also be highly beneficial.

The results obtained in the present work clearly revealed how a variety of normal operating and extreme wind-loading conditions can influence the service-life of a wind-turbine gearbox in the case when the service-life is controlled by the gear-tooth bending-fatigue.

The present work attempts to make a contribution to the resolution of an important problem related to premature-failure and inferior reliability of wind-turbine gearboxes.