Search results

The purpose of this experimental research was to examine a novel axial heat exchanger featuring swirling air movement over heated tubes. This apparatus is designed with perforated circular baffle plates complemented by rectangular air deflectors operating at different inclination angles. The tubes were arranged in a consistent layout parallel to the longitudinal airflow. The deflector’s heightened air-side turbulence initiates the frenzied motion, escalating the surface heat transfer rate.

The tubes maintained a constant heat flux condition over the surface. In each baffle plate, eight deflectors with identical inclination angles were devised in a reverse position, forming a rotation of air inside a circular duct that held tubes (carrying hot water) which elevated air-side turbulence, thereby enhancing the rate of heat transference on the surface. The baffle plates were equally situated from each other at changing pitch ratios. The Reynolds quantity was preserved in the scope of 16,000–30,000. The performance of the heat exchanger considering pitch ratios and inclination angles was examined.

The research indicates that when examined under similar conditions, an exchanger with a deflector baffle plate shows a strong dependence on the pitch ratio and inclination angle with a mean rise of 0.19 times in thermal enhancement factor at an inclination angle of 30° and a pitch ratio of 1.2 contrasted with an exchanger with segmental baffle plates.

The result shows the dependence of pitch ratio, Reynolds number and inclination on the heat transfer and friction factor rate.

The type 120 emergency valve is an essential braking component of railway freight trains, but corresponding diaphragms consisting of natural rubber (NR) and chloroprene rubber (CR) exhibit insufficient aging resistance and low-temperature resistance, respectively. In order to develop type 120 emergency valve rubber diaphragms with long-life and high-performance, low-temperatureresistant CR and NR were processed.

The physical properties of the low-temperature-resistant CR and NR were tested by low-temperature stretching, dynamic mechanical analysis, differential scanning calorimetry and thermogravimetric analysis. Single-valve and single-vehicle tests of type 120 emergency valves were carried out for emergency diaphragms consisting of NR and CR.

The low-temperature-resistant CR and NR exhibited excellent physical properties. The elasticity and low-temperature resistance of NR were superior to those of CR, whereas the mechanical properties of the two rubbers were similar in the temperature range of 0 °C–150 °C. The NR and CR emergency diaphragms met the requirements of the single-valve test. In the low-temperature single-vehicle test, only the low-temperature sensitivity test of the NR emergency diaphragm met the requirements.

The innovation of this study is that it provides valuable data and experience for future development of type 120 valve rubber diaphragms.

The purpose of the study is to propose a novel implementation of twisted tape in sinusoidal wavy-walled tubes to enhance the rate of heat transfer without compromising thermal efficiency. The study numerically investigates the fluid flow characteristics and analyzes the effect of different geometrical configurations, including wall wave amplitude, tape twist angles and nanoparticle volume fractions, on heat transfer improvement and performance factor.

This problem is numerically investigated using computational fluid dynamics, and the method is the finite volume method. A two-phase mixture model is used for nanofluid modeling.

The study investigated the effect of wall waviness, twisted tape, and nanoparticles on forced convective heat transfer and friction factor behavior in laminar pipe flow in three different Reynolds number regimes. The results showed that implementing twisted tape in wavy tubes significantly increased the rate of heat transfer and the performance factor, with the best twist ratio between 90 and 180°. Adding nanoparticles also enhanced heat transfer and performance factor, but to a lesser extent than wavy wall-twisted tape combinations. The study suggests selecting a proper combination of wavy wall and twisted tape at each Reynolds number to achieve an optimum solution.

To the best of the authors’ knowledge, the implementation of the selected passive methods in sinusoidal wavy tubes has not been studied before, and no previous studies have taken into account such a mix of heat transfer improvement techniques.

The purpose of this paper is to compile a comprehensive status report on pipes/piping networks across different industrial sectors, along with specifications of materials and sizes, and showcase welding avenues. It further extends to highlight the promising friction stir welding as a single solid-state pipe welding procedure. This paper will enable all piping, welding and friction stir welding stakeholders to identify scope for their engagement in a single window.

The paper is a review paper, and it is mainly structured around sections on materials, sizes and standards for pipes in different sectors and the current welding practice for joining pipe and pipe connections; on the process and principle of friction stir welding (FSW) for pipes; identification of main welding process parameters for the FSW of pipes; effects of process parameters; and a well-carved-out concluding summary.

A well-carved-out concluding summary of extracts from thoroughly studied research is presented in a structured way in which the avenues for the engagement of FSW are identified.

The implications of the research are far-reaching. The FSW is currently expanding very fast in the welding of flat surfaces and has evolved into a vast number of variants because of its advantages and versatility. The application of FSW is coming up late but catching up fast, and as a late starter, the outcomes of such a review paper may support stake holders to expand the application of this process from pipe welding to pipe manufacturing, cladding and other high-end applications. Because the process is inherently inclined towards automation, its throughput rate is high and it does not need any consumables, the ultimate benefit can be passed on to the industry in terms of financial gains.

To the best of the authors’ knowledge, this is the only review exclusively for the friction stir welding of pipes with a well-organized piping specification detailed about industrial sectors. The current pipe welding practice in each sector has been presented, and the avenues for engaging FSW have been highlighted. The FSW pipe process parameters are characteristically distinguished from the conventional FSW, and the effects of the process parameters have been presented. The summary is concise yet comprehensive and organized in a structured manner.

In 2016, the ISO/TS 16949 quality management standard for the automotive industry evolved to IATF 16949. The update brought new requirements that need to be analyzed before being implemented in organizations. Therefore, the purpose of this article is to propose guidelines to assist organizations in the automotive sector in the implementation of the elements added in the update to the IATF 16949 standard.

To fulfill this objective, the identification and analysis of the elements added in the evolution from ISO/TS 16949 to IATF 16949 was carried out, and four case studies were conducted in Brazilian automotive companies.

The main elements added to IATF 16949 with the update of the standard are the use of process failure mode effects analysis (PFMEA) for risk analysis; the development of a communication channel for employees to report cases of misconduct and non-conformities; procedures for controlling repaired/reworked products and temporary changes; and the inclusion of autonomous maintenance for the full implementation of total productive maintenance (TPM).

The main practical implication/contribution of the research is the proposed guidelines, which can support managers and automotive companies that want to implement, or will go through, the IATF certification process. The article's originality lies in the combination of a theoretical framework and case study analyses to develop the guidelines.

In the COVID-19 outbreak periods, people's life has been deranged, leading to disrupt the world. Firstly, the number of deaths is growing and has the potential to surpass the highest level at any time. Secondly, the pandemic broke many countries' fortified lines of epidemic prevention and gave people a more honest view of its seriousness. Finally, the pandemic has an impact on life, and the economy led to a shortage in medical, including a lack of clinicians, facilities and medical equipment. One of those, a simple ventilator is a necessary piece of medical equipment since it might be useful for a COVID-19 patient's treatment. In some cases, the COVID-19 patients require to be treated by modern ventilators to reduce lung damage. Therefore, the addition of simple ventilators is a necessity to relieve high work pressure on medical bureaucracies. Some low-income countries aim to build a simple ventilator for primary care and palliative care using locally accessible and low-cost components. One of the simple principles for producing airflow is to squeeze an artificial manual breathing unit (AMBU) iterative with grippers, which imitates the motion of human fingers. Unfortunately, the squeezing angle of grippers is not proportional to the exhaust air volume from the AMBU bag. This paper aims to model the AMBU bag by a mathematical equation that enables to implement on a simple controller to operate a bag-valve-mask (BVM) ventilator with high accuracy performance.

This paper provides a curvature function to estimate the air volume exhausting from the AMBU bag. Since the determination of the curvature function is sophisticated, the coefficients of the curvature function are approximated by a quadratic function through the experimental identification method. To obtain the high accuracy performance, a linear regression model and a least square method are employed to investigate the characteristic of the BVM ventilator's grippers angle with respect to the airflow volume produced by the AMBU bag.

This paper investigates the correlation between the exhausting airflow of the AMBU bag and the grippers angle of the BVM ventilator.

The experimental results validated that the regression model of the characteristic of the exhausting airflow of the AMBU bag with respect to the grippers' angle has been fitted with a coefficient over 98% within the range of 350–750 ml.

This study aims to analyze simplified methods for modelling the flow through perforated elements (i.e. porous baffle interface and porous region), searching for a faster and easier way to simulate these components. The numerical simulations refer to a muffler geometry available in literature as a case study.

The installation of scrubber onboard ships to satisfy the International Maritime Organization emissions regulations is a reliable and efficient solution. However, scrubbers have considerable dimensions, interfering with other exhaust line components. Therefore, scrubber installation in the funnels requires integration with other elements, for example, silencers. Perforated pipes and plates represent the main elements of scrubber and silencers. The study of their layout is, therefore, necessary to reduce emissions and noise. Numerical simulations allow evaluating the efficiency of integrated components.

The study highlights that velocity and pressure predicted by the simplified models have a strong correlation with the resistance coefficients. Even though the simplified models do not accurately reproduce the flow through the holes, the use of such models allows a fast and easy comparison between concurrent muffler geometries, giving aid in the early design phases.

The lack of general guidelines and comparisons in the literature between different modelling strategies of perforated elements supports the novelty of the present work and its impact on design applications. Study the flow inside scrubbers and mufflers is fundamental to evaluate their performances. Therefore, having a simple numerical method is suited for industrial applications during the design process.

Diesel has traditionally been considered the best-suited and most widely used fuel in various sectors, including manufacturing industries, power production, automobiles and transportation. However, with the ongoing crisis of fossil fuel inadequacy, the search for alternative fuels and their application in these sectors has become increasingly important. One particularly interesting and beneficial alternative fuel is biodiesel derived from bio sources.

In this research, an attempt was made to use biodiesel in an unconventional micro gas turbine engine. It will remove the concentric use of diesel engines for power production by improving fuel efficiency as well as increasing the power production rate. Before the fuel is used enormously, it has to be checked in many ways such as performance, emission and combustion analysis experimentally.

In this paper, a detailed experimental study was made for the use of Spirulina microalgae biodiesel in a micro gas turbine. A small-scale setup with the primary micro gas turbine and secondary instruments such as a data acquisition system and AVL gas analyser. The reason for selecting the third-generation microalgae is due to its high lipid and biodiesel production rate. For the conduction of experimental tests, certain conditions were followed in addition that the engine rotating rpm was varied from 4,000, 5,000 and 6,000 rpm. The favourable and predicted results were obtained with the use of microalgae biodiesel.

The performance and combustion results were not exactly equal or greater for biodiesel blends but close to the values of pure diesel; however, the reduction in the emission of CO was at the appreciable level for the used spirulina microalgae biodiesel. The emission of nitrogen oxides and carbon dioxide was a little higher than the use of pure diesel. This experimental analysis results proved that the use of spirulina microalgae biodiesel is both economical and effective replacement for fossil fuel.

The purpose of this paper is to understand the effect of basin water depth towards the cumulative distillate yield of the traditional and developed single basin double slope solar still (DSSS).

Modified single basin DSSS integrated with solar operated vacuum fan and external water cooled condenser was fabricated using aluminium material. During sunny season, experimental investigations have been performed in both conventional and modified DSSS at a basin water depth of 3, 6, 9 and 12 cm. Production rate and cumulative distillate yield obtained in traditional and developed DSSS at different water depths were compared and best water depth to attain the maximum productivity and cumulative distillate yield was found out.

Results indicated that both traditional and modified double SS produced maximum yield at the minimum water depth of 3 cm. Cumulative distillate yield of the developed SS was 16.39%, 18.86%, 15.22% and 17.07% higher than traditional at water depths of 3, 6, 9 and 12 cm, respectively. Cumulative distillate yield of the developed SS at 3 cm water depth was 73.17% higher than that of the traditional SS at 12 cm depth.

Performance evaluation of DSSS at various water depths by integrating the combined solar operated Vacuum fan and external Condenser.

The COVID-19 pandemic has caused severe challenges to ethnic minorities in the UK. While the experiences of migrants are both complex and varied depending on individuals' social class, race, cultural proximity to the host country and acculturation levels, more in-depth studies are necessary to fully understand how COVID-19 affects specific migrant groups and their health. Taiwanese migrants were selected because they are an understudied group. Also, there were widespread differences in pandemic management between the UK and Taiwan, making this group an ideal case for understanding how their acculturation journey can be disrupted by a crisis.

Qualitative data were collected at two different time points, at the start of the UK pandemic (March/April 2020) and six months on (October/November 2020), to explore migrant coping experiences over time. Theoretically, the authors apply acculturation theory through the lens of coping, while discussing health-consumption practices, as empirical evidence.

Before the outbreak of the pandemic, participants worked hard to achieve high levels of integration in the UK. The pandemic changed this; participants faced unexpected changes in the UK’s sociocultural structures. They were forced to exercise the layered and complex “coping with coping” in a hostile host environment that signalled their new marginalised status. They faced impossible choices, from catching a life-threatening disease to being seen as overly cautious. Such experience, over time, challenged their integration to the host country, resulting in a loss of faith in the UK’s health system, consequently increasing separation from the host culture and society.

It is important to note that the Taiwanese sample recruited through Facebook community groups is biased and has a high level of homogeneity. These participants were well-integrated, middle-class migrants who were highly educated, relatively resourceful and active on social media. More studies are needed to fully understand the impact on well-being and acculturation of migrants from different cultural, contextual and social backgrounds. This being the case, the authors can speculate that migrants with less resource are likely to have found the pandemic experience even more challenging. More studies are needed to fully understand migrant experience from different backgrounds.

Public health policymakers are advised to dedicate more resources to understand migrants' experiences in the host country. In particular, this paper has shown how separation, especially if embraced temporarily, is not necessarily a negative outcome to be corrected with specific policies. It can be strategically adopted by migrants as a way of defending their health and well-being from an increasingly hostile environment. Migrants' home country experience provides vicarious learning opportunities to acquire good practices. Their voices should be encouraged rather than in favour of a surprising orthodox and rather singular approach in the discussion of public health management.

The paper has clear public health policy implications. Firstly, public health policymakers are advised to dedicate more resources to understand migrants' experiences in the host country. Acknowledging migrants' voice is a critical first step to contribute to the development of a fair and inclusive society. Secondly, to retain skilful migrants and avoid a future brain-drain, policymakers are advised to advance existing infrastructure to provide more incentives to support and retain migrant talents in the post-pandemic recovery phase.

This paper reveals how a group of previously well-integrated migrants had to exercise “coping with coping” during the COVID crisis. This experience, over time, challenged their integration to the host country, resulting in a loss of faith in the UK’s health system, consequently increasing separation from the host culture and society. It contributes to the understanding of acculturation by showing how a such crisis can significantly disrupt migrants' acculturation journey, challenging them to re-acculturate and reconsider their identity stance. It shows how separation was indeed a good option for migrants for protecting their well-being from a newly hostile host environment.