Search results
1 – 10 of 69Samuel Kvasnicka, Thomas Bauernfeind, Paul Baumgartner and Riccardo Torchio
The purpose of this paper is to show that the computation of time-periodic signals for coupled antenna-circuit problems can be substantially accelerated by means of the single…
Abstract
Purpose
The purpose of this paper is to show that the computation of time-periodic signals for coupled antenna-circuit problems can be substantially accelerated by means of the single shooting method. This allows an efficient analysis of nonlinearly loaded coupled loop antennas for near field communication (NFC) applications.
Design/methodology/approach
For the modelling of electrically small coupled field-circuit problems, the partial element equivalent circuit (PEEC) method shows to be very efficient. For analysing the circuit-like description of the coupled problem, this paper developed a generalised modified nodal analysis (MNA) and applied it to specific NFC problems.
Findings
It is shown that the periodic steady state (PSS) solution of the resulting differential-algebraic system can be computed very time efficiently by the single shooting method. A speedup of roughly 114 to conventional transient approaches can be achieved.
Practical implications
The proposed approach appears to be an efficient alternative for the computation of time PSS solutions for nonlinear circuit problems coupled with discretised conductive structures, where the homogeneous solution is not of interest.
Originality/value
The present paper explores the implementation and application of the shooting method for nonlinearly loaded coupled antenna-circuit problems based on the PEEC method and shows the efficiency of this approach.
Details
Keywords
- Circuit analysis
- Transient analysis
- Time-domain modelling
- Equivalent circuit model
- Computational electromagnetics
- Field circuit models
- Near field communication
- Nonlinear resistive loads
- Full-wave rectifier
- Partial element equivalent circuit method
- Modified nodal analysis
- Differential-algebraic equation
- Backward differentiation formula
- Single shooting method
Peiqing Li, Huile Wang, Zixiao Xing, Kanglong Ye and Qipeng Li
The operation state of lithium-ion battery for vehicle is unknown and the remaining life is uncertain. In order to improve the performance of battery state prediction, in this…
Abstract
Purpose
The operation state of lithium-ion battery for vehicle is unknown and the remaining life is uncertain. In order to improve the performance of battery state prediction, in this paper, a joint estimation method of state of charge (SOC) and state of health (SOH) for lithium-ion batteries based on multi-scale theory is designed.
Design/methodology/approach
In this paper, a joint estimation method of SOC and SOH for lithium-ion batteries based on multi-scale theory is designed. The venin equivalent circuit model and fast static calibration method are used to fit the relationship between open-circuit voltage and SOC, and the resistance and capacitance parameters in the model are identified based on exponential fitting method. A battery capacity model for SOH estimation is established. A multi-time scale EKF filtering algorithm is used to estimate the SOC and SOH of lithium-ion batteries.
Findings
The SOC and SOH changes in dynamic operation of lithium-ion batteries are accurately predicted so that batteries can be recycled more effectively in the whole vehicle process.
Originality/value
A joint estimation method of SOC and SOH for lithium-ion batteries based on multi-scale theory is accurately predicted and can be recycled more effectively in the whole vehicle process.
Details
Keywords
Hui Wang, Qunzhan Li, Wei Liu, Chuang Wang and Tongtong Liu
The traction cable is paralleled with the existing traction network of electrified railway through transverse connecting line to form the scheme of long distance power supply for…
Abstract
Purpose
The traction cable is paralleled with the existing traction network of electrified railway through transverse connecting line to form the scheme of long distance power supply for the traction network. This paper aims to study the scheme composition and power supply distance (PSD) of the scheme.
Design/methodology/approach
Based on the structure of parallel traction network (referred to as “cable traction network (CTN)”), the power supply modes (PSMs) are divided into cable + direct PSM and cable + autotransformer (AT) PSM (including Japanese mode, French mode and new mode). Taking cable + Japanese AT PSM as an example, the scheme of long distance power supply for CTN under the PSMs of co-phase and out-of-phase power supply are designed. On the basis of establishing the equivalent circuit model and the chain circuit model of CTN, taking the train working voltage as the constraint condition, and based on the power flow calculation of multiple train loads, the calculation formula and process for determining the PSD of CTN are given. The impedance and PSD of CTN under the cable + AT PSM are simulated and analyzed, and a certain line is taken as an example to compare the scheme design.
Findings
Results show that the equivalent impedance of CTN under the cable + AT PSM is smaller, and the PSD is about 2.5 times of that under the AT PSM, which can effectively increase the PSD and the flexibility of external power supply location.
Originality/value
The research content can effectively improve the PSD of traction power supply system and has important reference value for the engineering application of the scheme.
Details
Keywords
Yaxing Ren, Saqib Jamshed Rind and Lin Jiang
A standalone microgrid (MG) is able to use local renewable resources and reduce the loss in long distance transmission. But the single-phase device in a standalone MG can cause…
Abstract
Purpose
A standalone microgrid (MG) is able to use local renewable resources and reduce the loss in long distance transmission. But the single-phase device in a standalone MG can cause the voltage unbalance condition and additional power loss that reduces the cycle life of battery. This paper proposes an energy management strategy for the battery/supercapacitor (SC) hybrid energy storage system (HESS) to improve the transient performance of bus voltage under unbalanced load condition in a standalone AC microgrid (MG).
Design/methodology/approach
The SC has high power density and much more cycling times than battery and thus to be controlled to absorb the transient and unbalanced active power as well as the reactive power under unbalanced condition. Under the proposed energy management design, the battery only needs to generate balanced power to balance the steady state power demand. The energy management strategy for battery/SC HESS in a standalone AC MG is validated in simulation study using PSCAD/EMTDC.
Findings
The results show that the energy management strategy of HESS maintains the bus voltage and eliminates the unbalance condition under single-phase load. In addition, with the SC to absorb the reactive power and unbalanced active power, the unnecessary power loss in battery is reduced with shown less accumulate depth of discharge and higher average efficiency.
Originality/value
With this technology, the service life of the HESS can be extended and the total cost can be reduced.
Details
Keywords
Sami Barmada, Nunzia Fontana, Leonardo Sandrolini and Mattia Simonazzi
The purpose of this paper is to gain a better understanding on how metasurfaces behave, in terms of currents in each unit cell. A better knowledge of their behavior could lead to…
Abstract
Purpose
The purpose of this paper is to gain a better understanding on how metasurfaces behave, in terms of currents in each unit cell. A better knowledge of their behavior could lead to an ad-hoc design for specific applications.
Design/methodology/approach
The methodology used is both theoretical and numerical; it is based on circuit theory and on an optimization procedure.
Findings
The results show that when the knowledge of the current in each unit cell of a metasurface is needed, the most common approximations currently used are often not accurate. Furthermore, a procedure for the termination of a metasurface, with application-driven goals, is given.
Originality/value
This paper investigates the distribution of the currents in a 2D metamaterial realized with magnetically coupled resonant coils. Different models for the analysis of these structures are illustrated, and the effects of the approximations they introduce on the current values are shown and discussed. Furthermore, proper terminations of the resonators on the boundaries have been investigated by implementing a numerical optimization procedure with the purpose of achieving a uniform distribution of the resonator currents. The results show that the behavior of a metasurface (in terms of currents in each single resonator) depends on different properties; as a consequence, their design is not a trivial task and is dependent on the specific applications they are designed for. A design strategy, with lumped impedance termination, is here proposed.
Details
Keywords
Dennis Albert, Lukas Daniel Domenig, Philipp Schachinger, Klaus Roppert and Herwig Renner
The purpose of this paper is to investigate the applicability of a direct current (DC) hysteresis measurement on power transformer terminals for the subsequent hysteresis model…
Abstract
Purpose
The purpose of this paper is to investigate the applicability of a direct current (DC) hysteresis measurement on power transformer terminals for the subsequent hysteresis model parametrization in transformer grey box topology models.
Design/methodology/approach
Two transformer topology models with two different hysteresis models are used together with a DC hysteresis measurement via the power transformer terminals to parameterize the hysteresis models by means of an optimization. The calculated current waveform with the derived model in the transformer no-load condition is compared to the measured no-load current waveforms to validate the model.
Findings
The proposed DC hysteresis measurement via the power transformer terminals is suitable to parametrize two hysteresis models implemented in transformer topology models to calculate the no-load current waveforms.
Originality/value
Different approaches for the measurement and utilization of transformer terminal measurements for the hysteresis model parametrization are discussed in literature. The transformer topology models, derived with the presented approach, are able to reproduce the transformer no-load current waveform with acceptable accuracy.
Details
Keywords
Mitja Garmut and Martin Petrun
This paper presents a comparative study of different stator-segmentation topologies of a permanent magnet synchronous machine (PMSM) used in traction drives and their effect on…
Abstract
Purpose
This paper presents a comparative study of different stator-segmentation topologies of a permanent magnet synchronous machine (PMSM) used in traction drives and their effect on iron losses. Using stator segmentation allows one to achieve more significant copper fill factors, resulting in increased power densities and efficiencies. The segmentation of the stators creates additional air gaps and changes the soft magnetic material’s material properties due to the cut edge effect. The aim of this paper is to present an in-depth analysis of the influence of stator segmentation on iron losses. The main goal was to compare various segmentation methods under equal excitation conditions in terms of their influence on iron loss.
Design/methodology/approach
A transient finite element method analysis combined with an extended iron-loss model was used to evaluate discussed effects on the stator’s iron losses. The workflow to obtain a homogenized airgap length accounting for cut edge effects was established.
Findings
The paper concludes that the segmentation in most cases slightly decreases the iron losses in the stator because of the overall reduced magnetic flux density B due to the additional air gaps in the magnetic circuit. An increase of the individual components, as well as total power loss, was observed in the Pole Chain segmentation design. In general, segmentation did not change the total iron losses significantly. However, different segmentation methods resulted in the different distortion of the magnetic field and, consequently, in different iron loss compositions. The analysed segmentation methods exhibited different iron loss behaviour with respect to the operation points of the machine. The final finding is that analysed stator segmentations had a negligible influence on the total iron loss. Therefore, applying segmentation is an adequate measure to improve PMSMs as it enables, e.g. increase of the winding fill factor or simplifying the assembly processes, etc.
Originality/value
The influence of stator segmentation on iron losses was analysed. An in-depth evaluation was performed to determine how the discussed changes influence the individual iron loss components. A workflow was developed to achieve a computationally cheap homogenized model.
Details
Keywords
The paper proposes an efficient and insightful approach for solving neutral delay differential equations (NDDE) with high-frequency inputs. This paper aims to overcome the need to…
Abstract
Purpose
The paper proposes an efficient and insightful approach for solving neutral delay differential equations (NDDE) with high-frequency inputs. This paper aims to overcome the need to use a very small time step when high frequencies are present. High-frequency signals abound in communication circuits when modulated signals are involved.
Design/methodology/approach
The method involves an asymptotic expansion of the solution and each term in the expansion can be determined either from NDDE without oscillatory inputs or recursive equations. Such an approach leads to an efficient algorithm with a performance that improves as the input frequency increases.
Findings
An example shall indicate the salient features of the method. Its improved performance shall be shown when the input frequency increases. The example is chosen as it is similar to that in literature concerned with partial element equivalent circuit (PEEC) circuits (Bellen et al., 1999). Its structure shall also be shown to enable insights into the behaviour of the system governed by the differential equation.
Originality/value
The method is novel in its application to NDDE as arises in engineering applications such as those involving PEEC circuits. In addition, the focus of the method is on a technique suitable for high-frequency signals.
Details
Keywords
In this paper we study a class of complexity measures, induced by a new data structure for representing k-valued functions (operations), called minor decision diagram. When…
Abstract
In this paper we study a class of complexity measures, induced by a new data structure for representing k-valued functions (operations), called minor decision diagram. When assigning values to some variables in a function the resulting functions are called subfunctions, and when identifying some variables the resulting functions are called minors. The sets of essential variables in subfunctions of
We examine the maximal separable subsets of variables and their conjugates, introduced in the paper, proving that each such set has at least one conjugate. The essential arity gap
Details
Keywords
Matteo Davide Lorenzo Dalla Vedova and Pier Carlo Berri
The purpose of this paper is to propose a new simplified numerical model, based on a very compact semi-empirical formulation, able to simulate the fluid dynamics behaviors of an…
Abstract
Purpose
The purpose of this paper is to propose a new simplified numerical model, based on a very compact semi-empirical formulation, able to simulate the fluid dynamics behaviors of an electrohydraulic servovalve taking into account several effects due to valve geometry (e.g. flow leakage between spool and sleeve) and operating conditions (e.g. variable supply pressure or water hammer).
Design/methodology/approach
The proposed model simulates the valve performance through a simplified representation, deriving from the linearized approach based on pressure and flow gains, but able to evaluate the mutual interaction between boundary conditions, pressure saturation and leak assessment. Its performance was evaluated comparing with other fluid dynamics numerical models (a detailed physics-based high-fidelity one and other simplified models available in the literature).
Findings
Although still showing some limitations attributable to its simplified formulation, the proposed model overcomes several deficiencies typical of the most common fluid dynamic models available in the literature, describing the water hammer and the nonlinear dependence of the delivery differential pressure with the spool displacement.
Originality/value
Although still based on a simplified formulation with reduced computational costs, the proposed model introduces a new nonlinear approach that, approximating with suitable precision the pressure-flow fluid dynamic characteristic of a servovalve, overcomes the shortcomings typical of such models.
Details