Search results

This paper aims to report the effect of titanium oxide (TiO₂) particles on the physical, mechanical, tribological and water resistance properties of 5% NaOH-treated bamboo fiber–reinforced composites.

In this research, the epoxy/bamboo/TiO₂ hybrid composite filled with 0–8 Wt.% TiO₂ particles has been fabricated using simple hand layup techniques, and testing of the developed composite was done in accordance with the American Society for Testing and Materials (ASTM) standard.

The results of this study indicate that the addition of TiO₂ particles improved the mechanical properties of the developed epoxy/bamboo composites. Tensile properties were found to be maximum for 6 Wt.%, and impact strength was found to be maximum for 8 Wt.% TiO₂ particles-filled composite. The highest flexural properties were found at a lower TiO₂ fraction of 2 Wt.%. Adding TiO₂ filler helped to reduce the water absorption rate. The studies related to the wear and friction behavior of the composite under dry and abrasive wear conditions reveal that TiO₂ filler was beneficial in improving the wear performance of the composite.

This research paper attempts to include both TiO₂ filler and bamboo fibers to develop a novel composite material. TiO₂ micro and nanoparticles are promising filler materials; it helps to enhance the mechanical and tribological properties of the epoxy composites and in literature, there is not much work reported, where TiO₂ is used as a filler material with bamboo fiber–reinforced epoxy composites.

This paper aims to report the effect of titanium oxide (TiO₂) particles on the specific wear rate (SWR) of alkaline treated bamboo and flax fiber-reinforced composites (FRCs) under dry sliding condition by using a robust statistical method.

In this research, the epoxy/bamboo and epoxy/flax composites filled with 0–8 Wt.% TiO₂ particles have been fabricated using simple hand layup techniques, and wear testing of the composite was done in accordance with the ASTM G99-05 standard. The Taguchi design of experiments (DOE) was used to conduct a statistical analysis of experimental wear results. An analysis of variance (ANOVA) was conducted to identify significant control factors affecting SWR under dry sliding conditions. Taguchi prediction model is also developed to verify the correlation between the test parameters and performance output.

The research study reveals that TiO₂ filler particles in the epoxy/bamboo and epoxy/flax composite will improve the tribological properties of the developed composites. Statistical analysis of SWR concludes that normal load is the most influencing factor, followed by sliding distance, Wt.% TiO2 filler and sliding velocity. ANOVA concludes that normal load has the maximum effect of 31.92% and 35.77% and Wt.% of TiO2 filler has the effect of 17.33% and 16.98%, respectively, on the SWR of bamboo and flax FRCs. A fairly good agreement between the Taguchi predictive model and experimental results is obtained.

This research paper attempts to include both TiO₂ filler and bamboo/flax fibers to develop a novel hybrid composite material. TiO₂ micro and nanoparticles are promising filler materials, it helps to enhance the mechanical and tribological properties of the epoxy composites. Taguchi DOE and ANOVA used for statistical analysis serve as guidelines for academicians and practitioners on how to best optimize the control variable with particular reference to natural FRCs.

This paper aims to study the possibility of electroplating copper coatings on chemically and chemical-galvanically nickel-plated acrylic fibers, to be further processed into yarn, fabrics, knitwear and nonwoven materials.

Electrically conductive fibers with different copper contents have been obtained, and the effect of electrolyte pH, its composition, current strength at the first and second cathodes, as well as the metallization time on the electrophysical, physical and mechanical properties of copper-containing fibers, has been studied.

The studies have shown that with an increase in the copper content, the electrical conductivity, the uniformity of the coating and the uniformity of the electrophysical properties (for chemical-galvanically nickel-plated fiber) increase. In the case of copper plating of chemically nickel-plated fiber, the coefficient of variation in electrical resistance increases with increasing plating time, even though the copper content increases, and the coefficient of variation in copper content and electrical resistance decreases. The physical and mechanical properties of copper-containing fibers differ slightly from the original (subjected to copper plating) and industrial Nitron fibers. With copper plating, the strength of the fiber practically does not decrease, and the elongation decreases somewhat, compared with the mass-produced Nitron fiber.

The physical and mechanical properties of copper-containing fibers are quite high, which makes it possible to be successfully further processed into yarn, fabrics, knitwear and nonwoven materials.

Electrical characteristics of transformer oil (TO) have been studied during normal and thermal aging conditions. In this paper, breakdown voltage (BDV), partial discharge (PD), heat transfer results and the physical mechanisms considering the impact of varying the diameter of Al₂O₃ nanoparticles (NPs) have been investigated. Different quantities of the two sizes of Al₂O₃ were added to the oil using a two-step method to determine the positive effect of NPs on the electrical and thermal properties of TO. Finally, the physical mechanisms related to the obtained experimental results have been performed.

The implementation of nanoparticles in this paper was provided by US Research Nanomaterials, Inc., USA. The provided Al₂O₃ NPs have an average particle size of 20–80 nm and a specific surface area of 138 and 58 m²/g, respectively, which have a purity of over 99%. Thermal aging has been done. The IEC 60156 standard has been implemented to calculate the BDV, and a 500-mL volume test cell (Apar TO 1020) has been used. PD test is performed according to Standard IEC 60343, and a JDEVS-PDMA 300 device was used for this test.

BDV tests indicate that 20 nm Al₂O₃ is more effective at improving BDV than 80 nm Al₂O₃, with an improvement of 113% compared to 99% for the latter. The analysis of Weibull probability at BDV indicates that 20 nm Al₂O₃ performs better, with improvements of 141%, 125% and 112% at probabilities of 1, 10 and 50%, respectively. The results of the PD tests using the PDPR pattern also show that 20 nm Al₂O₃ is superior. For the heat transfer test, 0.05 g/L of both diameters were used to ensure fair conditions, and again, the advantage was with 20 nm Al₂O₃ (23% vs 18%).

The effect of Al₂O₃ NP diameter (20 and 80 nm) on various properties of virgin and aged TO has been investigated experimentally in this paper to examine the effect of proposed NP on electrical improvement of TO.

This study aims to fabricate multiwalled carbon nanotubes (MWCNTs)-mediated polyvinyl alcohol (PVA) composite films using the solution casting approach.

The prepared films were evaluated for diverse structural, surface, optical and electrical attributes using advanced analytical techniques, i.e. electron microscopy for surface morphology, Fourier transform infrared spectroscopy for tracing chemical functionalities, x-ray diffraction (XRD) for crystal patterns, water contact angle (WCA) analysis for surface wettability and UV visible spectroscopy for optical absorption parameters. The specimens were also investigated for certain rheological, mechanical and electrical properties, where applicable.

The surface morphology results expressed a better dispersion of MWCNTs in the resultant PVA-based nanocomposite film. The XRD analysis exhibited that the nanocomposite film was crystalline. The surface wettability analysis indicated that with the inclusion of MWCNTs, the WCA of the resultant nanocomposite film improved to 89.4° from 44° with the pristine PVA film. The MWCNTs (1.00%, w/w) incorporated PVA-based film exhibited a tensile strength of 54.0 MPa as compared to that of native PVA as 25.3 MPa film. There observed a decreased bandgap (from 5.25 to 5.14 eV) on incorporating the MWCNTs in the PVA-based nanocomposite film.

The MWCNTs’ inclusion in the PVA matrix could enhance the AC conductivity of the resultant nanocomposite film. The prepared nanocomposite film might be useful in designing certain optoelectronic devices.

The results demonstrated the successful MWCNTs mediation in the PVA-based composite films expressed good intercalation of the precursors; this resulted in decreased bandgap, usually, desirable for optoelectronic applications.

The purpose of this study is to utilize two types of gypsum mold wastes from two different factories as novel and economical reinforcing fillers for composites that may be useful for building materials and floors. Two types of gypsum mold wastes from two different factories as raw materials were incorporated into linear low density polyethylene (LLDPE) aiming to get rid of that waste in one hand and obtaining useful economical composites suitable for building materials and floors.

Composites were prepared from two types of gypsum mold wastes substituted with different ratios from raw gypsum and LLDPE throughout the melt blending technique. The physico-mechanical and electrical investigations in addition to the morphology of the composites were included.

The mechanical results illustrate that substituting commercial gypsum with gypsum mold waste positively affects tensile strength, flexural strength and hardness shore D for the LLDPE composites. The tensile strength increased from 5 MPa for LLDPE filled with commercial gypsum as blank samples to 11.2 and 13.2 MPa for LLDPE filled with D and S waste. Also, electrical properties which include both permittivity ɛ′ and dielectric loss ɛ″ increased with increasing the waste content in the LLDPE matrix. In addition to the electrical conductivity values, σ lies in the order of insulation materials. Consequently, it is possible to produce materials with a gypsum matrix by adding industrial waste, improving the behavior of the traditional gypsum and enabling those composites to be applied in various construction applications as eco-friendly tiles.

This study aims to prepare eco-friendly composites based on LLDPE and waste gypsum mold to preserve resources for the coming generations, other than lowering the environmental footprint and saving the costs of getting rid of it.

This paper aims to extracted sericin from the cocoons of Bombyx mori silkworms, and sericin powder was applied onto drawn textured polyethylene terephthalate (PET) yarns as a spin finish. The reactivity on the surface of PET yarns was analyzed through Fourier transform infrared spectrophotometry–attenuated total reflectance (FTIR-ATR) and dyeing with methylene blue as a reactive dye. Also, investigations were conducted on the effects of sericin, citrc acid (CA) (as a crosslinking agent), and sodium hypophosphite (as a catalyst) concentrations on some properties of false-twist textured PET yarns.

A false-twist texturing machine (Scragg-Shirley minibulk, England) was used with the draw ratio of 1.05, heating temperature of 120°C, texturing speed of 100 m min⁻¹ and applied twist of 3,000 TPM. The aqueous extraction of sericin was carried out by the boiling of the raw silk in distilled water with L:R: 40:1 for 120 min. The aqueous solution was filtered with a filter paper to remove the impurities and insoluble fibroin. Finally, the sericin solution was freeze-dried to obtain the sericin powder. The sericin solution was applied on the drawn textured PET yarns using the “pad-dry-cure” method.

Sericin fixation onto the PET yarns was confirmed by FTIR-ATR. The results showed that there were no significant changes in the tensile strength, linear density, crimp contraction and crimp modulus, elongation at break and shrinkage. In contrast, a substantial increase was observed in moisture regain, vertical wicking, dye uptake and ultraviolet protection. There was also a reduction just in the electrical resistivity, in the presence of sericin.

Although sericin has been known to have numerous beneficial properties, its application in textile industry as a spin finish has not been reported yet.

Identification of the direction of the sound source is very important for human–machine interfacing in the applications such as target detection on military applications and wildlife conservation. Considering its vast applications, this study aims to design, simulate, fabricate and test a bidirectional acoustic sensor having two cantilever structures coated with piezoresistive material for sensing has been designed, simulated, fabricated and tested.

The structure is a piezoresistive acoustic pressure sensor, which consists of two Kapton diaphragms with four piezoresistors arranged in Wheatstone bridge arrangement. The applied acoustic pressure causes diaphragm deflection and stress in diaphragm hinge, which is sensed by the piezoresistors positioned on the diaphragm. The piezoresistive material such as carbon or graphene is deposited at maximum stress area. Furthermore, the Wheatstone bridge arrangement has been formed to sense the change in resistance resulting into imbalanced bridge and two cantilever structures add directional properties to the acoustic sensor. The structure is designed, fabricated and tested and the dimensions of the structure are chosen to enable ease of fabrication without clean room facilities. This structure is tested with static and dynamic calibration for variation in resistance leading to bridge output voltage variation and directional properties.

This paper provides the experimental results that indicate sensor output variation in terms of a Wheatstone bridge output voltage from 0.45 V to 1.618 V for a variation in pressure from 0.59 mbar to 100 mbar. The device is also tested for directionality using vibration source and was found to respond as per the design.

The fabricated devices could not be tested for practical acoustic sources due to lack of facilities. They have been tested for a vibration source in place of acoustic source.

The piezoresistive bidirectional sensor can be used for detection of direction of the sound source.

In defense applications, it is important to detect the direction of the acoustic signal. This sensor is suited for such applications.

The present paper discusses a novel yet simple design of a cantilever beam-based bidirectional acoustic pressure sensor. This sensor fabrication does not require sophisticated cleanroom for fabrication and characterization facility for testing. The fabricated device has good repeatability and is able to detect the direction of the acoustic source in external environment.

The purpose of this study is to prepare a state-of-the-art review on advanced ceramic materials including their fabrication techniques, characteristics, applications and wettability.

This review paper presents the various types of advanced ceramic materials according to their compounding elements, fabrication techniques of advanced ceramic powders as well as their consolidation, their characteristics, applications and wetting properties. Hydrophobic/hydrophilic properties of advanced ceramic materials are described in the paper with their state-of-the-art application areas. Optical properties of fine ceramics with their intrinsic characteristics are also presented within. Special focus is given to the brief description of application-based manipulation of wetting properties of advanced ceramics in the paper.

The study of wetting/hydrophobicity/hydrophilicity of ceramic materials is important by which it can be further modified to achieve the required applications. It also makes some sense that the material should be tested for its wetting properties when it is going to be used in some important applications like biomedical and dental. Also, these advanced ceramics are now often used in the fabrication of filters and membranes to purify liquid/water so the study of wetting characteristics of these materials becomes essential. The optical properties of advanced ceramics are equally making them suitable for many state-of-the-art applications. Dental, medical, imaging and electronics are the few sectors that use advanced ceramics for their optical properties.

This review paper includes various advanced ceramic materials according to their compounding elements, different fabrication techniques of powders and their consolidation, their characteristics, various application area and hydrophobic/hydrophilic properties.

The aim of this paper is to provide a simple yet accurate and efficient geometric method for thermal homogenization of impregnated and non-impregnated coil winding technologies based on the concept of thermal resistance.

For regular windings, the periodic microscopic cell in the winding space is identified. Also, for irregular windings, the average microscopic cell of the winding is determined. An approximation is used to calculate the thermal resistance of the winding cell. Based on this approximation, the winding insulation is considered as a circular ring around the wire. Mathematical equations are obtained to calculate the equivalent thermal resistance of the cell. The equivalent thermal conductivity of the winding is calculated using equivalent thermal resistance of the cell. Winding thermal homogenization is completed by determining the equivalent thermal properties of the cell.

The thermal pattern of different windings is simulated and compared with the results of different homogenization methods. The results show that the proposed method is applicable for a wide range of windings in terms of winding scheme, packing factor and winding insulation. Also, the results show that the proposed method is more accurate than other winding homogenization methods in calculating the equivalent thermal conductivity of the winding.

In this paper, the change of electrical resistance of the winding with temperature and thermal contact between the sub-components are ignored. Also, liquid insulators, such as oils, and rectangular wires were not investigated. Research in these topics is considered as future work.

Unlike other homogenization methods, the proposed method can be applied to non-impregnated and irregular windings. Also, compared to other homogenization methods, the proposed method has a simpler formulation that makes it easier to program and implement. All of these indicate the efficiency of the proposed method in the thermal analysis of the winding.