Search results

The purpose of this paper is to present a dynamic analysis on the thermal and electrical properties of fabrics under wet conditions.

A purpose‐built apparatus is applied to test the thermal and electrical properties of textiles in moisture absorption and liberation process. Relation between temperature and resistance of a cotton/polyester double‐layer fabric is also analysed.

The surface temperature of textiles shows three different stages in the process. The electrical resistance is linearly related to the reciprocal of the moisture regain of fabrics. In the moisture absorption and liberation process, surface temperature of cotton layer is higher than that of polyester layer. And the electrical resistance of cotton layer decreases more quickly than that of polyester layer. The electrical resistance changes earlier than surface temperature in the moisture‐liberation process.

The paper is helpful in not only the designing of sportswear, but also the devising of moisture‐testing apparatus.

A dynamic testing method is applied to characterize the thermal and electrical properties of textiles.

Apart from the basic material properties of liquid lubricants, such as, e.g., the viscosity and density of the hydraulic fluid, it is also important to have information regarding the electrical properties of the fluid used. The latter is closely related to the purpose, type, structure, and conditions of use of a hydraulic system, especially the powertrain design and fluid condition monitoring. The insulating capacity of the hydraulic fluid is important in cases where the electric motor of the pump is immersed in the fluid. In other cases, on the basis of changing the electrical conductive properties of the hydraulic fluid, we can refer its condition, and, on this basis, the degree of degradation.

The paper first highlights the importance of knowing the electrical properties of hydraulic fluids and then aims to compare these properties, such as the breakdown voltage of commonly used hydraulic mineral oils and newer ionic fluids suitable for use as hydraulic fluids.

Knowledge of this property is crucial for the design approach of modern hydraulic compact power packs. In the following, the emphasis is on the more advanced use of known electrical quantities, such as electrical conductivity and the dielectric constant of a liquid.

Based on the changes in these quantities, we have the possibility of real-time monitoring the hydraulic fluid condition, on the basis of which we judge the degree of fluid degradation and its suitability for further use.

The purpose of this paper is to find out how to model the effect of mechanical stresses on the magnetic properties of electrical steel used in electromagnetic devices and especially in electrical machines. Further, the effect of these stresses on the operation of the machines should be studied.

The constitutive equation of the electrical steel is usually modeled as a non linear relation between the magnetic flux density and the magnetic field strength. In this research, this constitutive equation is developed to account for the mechanical stresses through a parametric relationship, the parameters of which are estimated from measurements. Further, the constitutive equation is used in a magnetomechanically coupled numerical simulation of an induction machine.

The mechanical stresses degrade the properties of the electrical steel and increase the magnetization current in electrical machines. This leads to a decrease in the efficiency of these machines.

The effect of mechanical stresses is studied from the point of view of magnetization properties. This work does not model the effect of stresses on the specific losses of the material. Such a research is still going on.

The effect of mechanical stress on the magnetic properties of the materials used in electrical machines is modeled in an easy and original way, which allow for its application in numerical simulation and analysis of these machines.

This article aims to present a systematic and up-to-date account of carbon-based reinforcements, including carbon nanotube (CNT), carbon nanofibre (CNF), carbon black (CB), carbon fibre (CF) and grapheme, in shape-memory polymer (SMP) for electrical actuation.

Studies exploring carbon-based reinforcement in SMP composites for electrically conductive performance and Joule heating triggered shape recovery have been included, especially for the principle design, characterisation and shape recovery behaviour, making the article a comprehensive account of the systemic progress in SMP composite incorporating conductive carbon reinforcement.

SMPs are fascinating materials and have attracted great academic and industrial attention owing to their significant macroscopic shape deformation in the presence of an appropriate stimulus. The working mechanisms, the physico requirements and the theoretical origins of the different types of carbon-based reinforcement SMP composites have been discussed. Current research and development on the fabrication strategies of carbon-based reinforcement SMP composites have been summarised.

A systematic review is to evaluate carbon-based reinforcements in SMPs for electrical actuation and discuss recent developments and future applications.

Carbon-based reinforcements in SMPs can be used as smart deployable space structure in the broad field of aerospace technologies.

To reveal the research and development of utilising CNT, CNF, CB, CF and grapheme to achieve shape recovery of SMP composites through electrically resistive heating, which will significantly benefit the research and development of smart materials and systems.

This study aims to investigate the effect of bismuth addition (up to 30 Wt%) on the microstructure and electrical conductivity of a commercial lead-free alloy (SAC405) near the solder/substrate soldered joint. The system under study is referred in this work as (SAC405 + xBi)/Cu, as Cu is the selected substrate in which the solder was casted. The electrical resistivity of this system was investigated, considering Bi addition effect on the local microstructure and chemical composition gradients within that zone.

Solder joints between Cu substrate and SAC405 alloy with different levels of Bi were produced. The electrical conductivity along the obtained solder/substrate interface was measured by four-point probe method. The microstructure and chemical compositions were evaluated by scanning electron microscopy/energy dispersive spectroscopy analysis.

Two different electrical resistivity zones were identified within the solder interface copper substrate/solder alloy. At the first zone (from intermetallic compound [IMC] until approximately 100 μm) the increase of the electrical resistivity is gradual from the substrate to the solder side. This is because of the copper substrate diffusion, which established a chemical composition gradient near the IMC layer. At the second zone, electrical resistivity becomes much higher and is mainly dependent on the Bi content of the solder alloy. In both identified zones, electrical resistivity is affected by its microstructure, which is dependent on Cu and Bi content and solidification characteristics.

A detailed characterization of the solder/substrate zone, in terms of electrical conductivity, was done with the definition of two variation zones. With this knowledge, a better definition of processing parameters and in-service soldered electronic devices behavior can be achieved.

This paper aims to study the various developments taking place in the field of gas sensors made from polyaniline (PANI) nanocomposites, which leads to the development of high-performance electrical and gas sensing materials operating at room temperature.

PANI/ferrite nanocomposites exhibit good electrical properties with lower dielectric losses. There are numerous reports on PANI and ferrite nanomaterial-based gas sensors which have good sensing response, feasible to operate at room temperature, requires less power and cost-effective.

This paper provides an overview of electrical and gas sensing properties of PANI/ferrite nanocomposites having improved selectivity, long-term stability and other sensing performance of sensors at room temperature.

The main purpose of this review paper is to focus on PANI/ferrite nanocomposite-based gas sensors operating at room temperature.

A comparison of electric and viscosity percolation threshold is crucial from the scientific and technical points of view to understand the features and capabilities of heterogeneous graphene composite materials and properly select the functional phase volume. Therefore, the purpose of this paper is to present the analysis of the electrical and rheological percolation thresholds in the polymer–graphene screen printing pastes and the analysis of the relation between these two parameters.

In the paper, the properties of polymer-based pastes with graphene nanoplatelets were tested: paste viscosity and printed layers conductivity. The tests of pastes with different filler content allowed to determine both the electrical and rheological percolation thresholds using power law, according to Kirkpatrick’s percolation model.

The electrical percolation threshold for graphene nanoplatelets (GNPs) in the composite was 0.74 Vol.% when the rheological percolation threshold is observed to be at 1.00 Vol.% of nanoplatelets. The percolation threshold values calculated using the Kirkpatrick’s percolation model were 0.87 and 0.5 Vol.% of GNPs in the paste for electrical and rheological percolation thresholds, respectively.

Recently, GNPs are becoming more popular as the material of the functional phase in screen printing heterophase materials, because of their unique mechanical and electrical properties. However, till date no research presented in the literature is related to the direct comparison of both the electrical and rheological percolation thresholds. Such analysis is important for the optimization of the printing process toward the highest quality of printed conductive paths, and finally the best electrical properties.

In this study, AlCoCrFeNi–Cu (Cu-based) and AlCoCrFeNi–Ti (Ti-based) high entropy alloys (HEAs) were fabricated using a direct blown powder technique via laser additive manufacturing on an A301 steel baseplate for aerospace applications. The purpose of this research is to investigate the electrical resistivity and oxidation behavior of the as-built copper (Cu)- and titanium (Ti)-based alloys and to understand the alloying effect, the HEAs core effects and the influence of laser parameters on the physical properties of the alloys.

The as-received AlCoCrFeNiCu and AlCoCrFeNiTi powders were used to fabricate HEA clads on an A301 steel baseplate preheated at 400°C using a 3 kW Rofin Sinar dY044 continuous-wave laser-deposition system fitted with a KUKA robotic arm. The deposits were sectioned using an electric cutting machine and prepared by standard metallographic methods to investigate the electrical and oxidation properties of the alloys.

The results showed that the laser power had the most influence on the physical properties of the alloys. The Ti-based alloy had better resistivity than the Cu-based alloy, whereas the Cu-based alloy had better oxidation residence than the Ti-based alloy which attributed to the compositional alloying effect (Cu, aluminum and nickel) and the orderliness of the lattice, which is significantly associated with the electron transportation; consequently, the more distorted the lattice, the easier the transportation of electrons and the better the properties of the HEAs.

It is evident from the studies that the composition of HEAs and the laser processing parameters are two significant factors that influence the physical properties of laser deposited HEAs for aerospace applications.

A capacitor is a basic electronic passive component. Thick‐film technology allows manufacturing of capacitors covering the range of small and medium capacitances and they have been investigated in depth already. Low temperature co‐fired ceramics (LTCC) technology makes it possible to fabricate buried capacitors, which leads to increased packaging density, but such components’ properties are not well known. The purpose of this paper is to present the results of investigations on thick‐film and LTCC capacitors made in various technological variants.

Thick‐film and LTCC capacitors were made in various technological variants. Different capacitor inks, metallurgy of electrodes and component constructions were investigated. Basic electrical properties and stability were determined. An electrical equivalent circuit of such components was developed based on frequency and temperature characteristics.

Simple electrical equivalent circuits of self‐made thick‐film and LTCC micro‐capacitors were developed based on measurements in frequency and temperature domain. Good fitting accuracy was obtained. The bulk material section of model is predominant in the low‐frequency range. Interface region and serial resistance influence are revealed at higher frequency, affecting mainly dissipation factor value. Also, temperature and thermal ageing have affected strongly on that part of the model.

The paper usefully examines the electrical properties and electrical equivalent models of thick‐film and LTCC micro‐capacitors.

Recent work has demonstrated the possibility of selectively sintering polymer powders with radio frequency (RF) radiation as a means of rapid, volumetric additive manufacturing. Although RF radiation can be used as a volumetric energy source, non-uniform heating resulting from the sample geometry and electrode configuration can lead to adverse effects in RF-treated samples. This paper aims to address these heating uniformity issues by implementing a computational design strategy for doped polymer powder beds to improve the RF heating uniformity.

Two approaches for improving the RF heating uniformity are presented with the goal of developing an RF-assisted additive manufacturing process. Both techniques use COMSOL Multiphysics® to predict the temperature rise during simulated RF exposure for different geometries. The effectiveness of each approach is evaluated by calculating the uniformity index, which provides an objective metric for comparing the heating uniformity between simulations. The first method implements an iterative heuristic tuning strategy to functionally grade the electrical conductivity within the sample. The second method involves reorienting the electrodes during the heating stage such that the electric field is applied in two directions.

Both approaches are shown to improve the heating uniformity and predicted part geometry for several test cases when applied independently. However, the greatest improvement in heating uniformity is demonstrated by combining the approaches and using multiple electrode orientations while functionally grading the samples.

This work presents an innovative approach for overcoming RF heating uniformity issues to improve the resulting part geometry in an RF-assisted, volumetric additive manufacturing method.