Search results

This paper aims to introduce a novel concept of a double-wire feed (DWF) to alleviate heat accumulation and improve the cooling rate of the molten pool in gas tungsten arc (GTA)-based additive manufacturing (AM), in which the former wire is fed into the arc and the latter wire is melt by the molten pool.

The microstructure, phase composition and mechanical properties of 308 L stainless steel components built by single-wire feed (SWF) AM and DWF-AM are compared, and the differences are analyzed in detail.

The microstructures for both wire feeding modes include δ and γ phases. Compared with the SWF-AM, the sample fabricated in the DWF-AM exhibits finer microstructure, and the microstructure in the middle region is transformed from columnar grains to cellular grains. Microhardness of the sample produced in the DWF-AM is higher than the SWF-AM. In comparison to the SWF-AM, the tensile strength of the specimen fabricated using the DWF-AM reaches 571 MPa and increases by 16.14%.

This study proposes a novel concept of the DWF-AM to reduce heat accumulation as well as enhance the cooling rate of the molten pool, and improved mechanical properties of the 308 L stainless steel component are obtained.

The purpose of this paper is to find a theoretical reference to adjust the unsymmetrical arc shape and plasma flow of overlapping deposition in wire arc additive manufacturing (WAAM) and ensure the effect of the gas shielding and stable heat and mass transfer in deposition process. The multiphysical numerical simulation and physical experiment are used for validation.

In this study, welding torch tilt deposition and external parallel magnetic field–assisted deposition are presented to adjust the unsymmetrical arc shape and plasma flow of overlapping deposition, and a three-dimensional numerical model is developed to simulate the arc of torch tilt overlapping deposition and external parallel magnetic field–assisted overlapping deposition.

The comparison of simulated results indicate that the angle of welding torch tilt equal to 20° and the magnetic flux density of external transverse magnetic field equal to 0.001 Tesla are capable of balancing the electric arc and shielding gas effectively, respectively. The arc profiles captured by a high-speed camera match well with simulated results.

These studies of this paper can provide a theoretical basis and reference for the calibration and optimization of WAAM process parameters.

This study aims to propose and evaluate the progress in the basic-pixel (a strategy to generate continuous trajectories that fill out the entire surface) algorithm towards performance gain. The objective is also to investigate the operational efficiency and effectiveness of an enhanced version compared with conventional strategies.

For the first objective, the proposed methodology is to apply the improvements proposed in the basic-pixel strategy, test it on three demonstrative parts and statistically evaluate the performance using the distance trajectory criterion. For the second objective, the enhanced-pixel strategy is compared with conventional strategies in terms of trajectory distance, build time and the number of arcs starts and stops (operational efficiency) and targeting the nominal geometry of a part (operational effectiveness).

The results showed that the improvements proposed to the basic-pixel strategy could generate continuous trajectories with shorter distances and comparable building times (operational efficiency). Regarding operational effectiveness, the parts built by the enhanced-pixel strategy presented lower dimensional deviation than the other strategies studied. Therefore, the enhanced-pixel strategy appears to be a good candidate for building more complex printable parts and delivering operational efficiency and effectiveness.

This paper presents an evolution of the basic-pixel strategy (a space-filling strategy) with the introduction of new elements in the algorithm and proves the improvement of the strategy’s performance with this. An interesting comparison is also presented in terms of operational efficiency and effectiveness between the enhanced-pixel strategy and conventional strategies.

Wire and arc additive manufacturing (WAAM) technology-based cold metal transfer (CMT) to produce large aluminum alloy parts has become more and more popular. In WAAM, wire is the only raw material. The purpose of this paper is to study the effect of wire composition on the microstructure and properties of the ZAlCu5MnCdVA alloy deposited by WAAM.

Two thin-walled ZAlCu5MnCdVA alloys with different wire compositions were prepared by WAAM. The copper contents were 4.7% (Al-4.7Cu) and 5.0% (Al-5.0Cu), respectively. The microstructure, element distribution and evolution of precipitated phases of the two samples were characterized and analyzed by optical microscopy, scanning electron microscopy and transmission electron microscopy. Hardness and tensile properties of samples were tested, and strengthening mechanism was analyzed in detail.

The results show that grain sizes of Al-4.7Cu and Al-5.0Cu are less than 40 μm. The average mass fraction of Cu in Al matrix and the number of nanometer scale θ'' and θ' phases are the main factors affecting the tensile properties of Al-Cu alloy. Tensile properties of two materials show different characteristics at room temperature and high temperature. Al-5.0Cu is better at room temperature and Al-4.7Cu is better at high temperature. The yield strength (YS), ultimate tensile strength (UTS) and elongation in the x direction of Al-5.0Cu at room temperature are 451 ± 10.2 MPa, 486 ± 10.2 MPa and 9 ± 0.5%, respectively. The YS, UTS and elongation in the x direction of Al-4.7Cu at high temperature are 290 ± 4.5 MPa, 356 ± 7.0 MPa and 13% ± 0.2%, respectively.

Experiments show that the increase of Cu element can improve the properties at room temperature of the ZAlCu5MnCdVA alloy by WAAM, but its properties at high temperature decrease.

Increasingly stringent quality and cost requirements have brought about a revival in the use of stainless steel cloth as a production tool for screen printing. Process factors are examined to support the choice of stainless steel for its stability and potential for high registrational accuracy printing. Screen making is of vital importance to the end result, and the achievement and maintenance of uniform tension are as critical for stainless steel as for other screen media. Full specification of printing screen requirements is essential, as is incoming goods inspection of cloth and finished screens. The entire weaving process contributes to the overall quality of stainless steel cloth and, although post‐production correction procedures are available, they are undesirable and can be avoided by a carefully controlled weaving process.

The purpose of this paper is to improve the dimensional accuracy of inclined thin-walled parts fabricated by laser direct metal deposition (DMD) under an open-loop control system.

In this study, a novel method of the adaptive slicing method and DMD process with feedback adjustment of deposition height has been developed to successively fabricate complex inclined thin-walled square tube elbow parts. The defocus amount was used as a variable to the matching between the deposition thickness and the adaptive slicing height.

The low relative error of dimensional accuracy between experimental and designed parts shows that the matching of the single-layer deposition thickness and the adaptive slicing height can be realized by optimizing the defocusing amount. The negative feedback of the thin-wall part height can be achieved when the defocus amount and the z-axis increment are less than deposition thickness. The improvement of dimensional accuracy of inclined thin-walled parts is also attributed to the optimized scanning strategy.

The slicing method and deposition process can provide technical guidance for other additive manufacturing (AM) systems to fabricate metal thin-walled parts with high dimensional accuracy because the feedback control of deposition height can be realized only by the optimized process.

This study provides a novel adaptive slice method and corresponding the deposition process, and expands the slicing method of AM metal parts.

The purpose of this paper is to analyze and investigate heat accumulation caused by temperature changes and interface microstructure effected by element diffusion.

Al/Cu bimetallic structure is initially manufactured through laser powder bed fusion process. To minimize trial and error, finite element modeling is adopted to simulate temperature changes on the Al-based and Cu-based substrate.

The results show that forming pure copper on Al-based substrate can guarantee heat accumulation, providing enough energy for subsequent building. The instantaneous laser energy promotes increase of diffusion activation energy, resulting in the formation of transition zone derived from interdiffusion between Al and Cu atoms. The interface with a thickness of about 22 µm dominated by Kirkendall effect moves towards Al-rich side. The interface microstructure is mainly composed of a-Al, a-Cu and CuAl2 phase.

The bonding mechanism of Al/Cu interface is atom diffusion-induced chemical reaction. The theoretical basis provides guidance for structural design and production application.

An experimental investigation for developing structure-property correlations of hot-rolled E410 steels with different carbon contents, i.e. 0.04wt.%C and 0.17wt.%C metal active gas (MAG) and cold metal transfer (CMT)-MAG weldments was undertaken.

Mechanical properties and microstructure of MAG and CMT-MAG weldments of two E410 steels with varying content of carbon were compared using standardized mechanical testing procedures, and conventional microscopy.

0.04wt.%C steel had strained ferritic and cementite sub-structures in blocky shape and large dislocation density, while 0.17wt.%C steel consisted of pearlite and polygonal ductile ferrite. This effected yield strength (YS), and microhardness being larger in 0.04wt.%C steel, %elongation being larger in 0.17wt.%C steel. Weldments of both E410 steels obtained with CMT-MAG performed better than MAG in terms of YS, ultimate tensile strength (UTS), %elongation, and toughness. It was due to low heat input of CMT-MAG that resulted in refinement of weld metal, and subzones of heat affected zone (HAZ).

A substantial improvement in YS (∼9%), %elongation (∼38%), and room temperature impact toughness (∼29%) of 0.04wt.%C E410 steel is achieved with CMT-MAG over MAG welding. Almost ∼10, ∼12.5, and ∼16% increment in YS, %elongation, and toughness of 0.17wt.%C E410 steel is observed with CMT-MAG. Relatively low heat input of CMT-MAG leads to development of fine Widmanstätten and acicular ferrite in weld metal and microstructural refinement in HAZ subzones with nearly similar characteristics of base metal.