Search results

The dimple is adopted into a double wall cooling structure which is widely used in hot gas components to increase the heat transfer effects with relatively low pressure drop penalty. The purpose of this paper is to study the effect of dimple depth and dimple diameter on the target surface heat transfer and the inlet to outlet friction factor.

The study is carried out by using the numerical simulations. The impingement flow is directly impinging on the dimple and released from the film holes after passing the double wall chamber. The ratio between dimple depth and dimple diameter is varied from 0 to 0.4 and the ratio between dimple diameter and impingement hole diameter is ranging from 0.5 to 3. The Reynolds number is between 10,000 and 70,000. Results of the target surface Nusselt number, friction factor and flow structures are included. For convenience of comparison, the double wall cooling structure without the dimple is considered as the baseline.

It is found that the dimple can effectively enhance the target surface heat transfer due to thinning of the flow boundary layer and flow reattachment as well as flow recirculation outside the dimple near the dimple rim especially for the large Re number condition. However, the stagnation point heat transfer is reduced. It is also found that for a large dimple depth or large dimple diameter, a salient heat transfer reduction occurs for the toroidal vortex. The thermal performance indicates that the intensity of the heat transfer enhancement depends upon the dimple depth and dimple diameter

This is the first time to adopt a dimple into a double wall cooling structure. It suggests that the target surface heat transfer in a double wall cooling structure can be increased by the use of the dimple. However, the heat transfer characteristic is sensitive for the different dimple diameter and dimple depth which may result in a different flow behavior

The purpose of this study is to investigate the effects of film holes’ arrangements and jet Reynolds number on flow structure and heat transfer characteristics of jet impingement conjugated with film cooling in a semicylinder double wall channel.

Numerical simulations are used in this research. Streamlines on different sections, skin-friction lines, velocity, wall shear stress and turbulent kinetic energy contours near the concave target wall and vortices in the double channel are presented. Local Nusselt number contours and surface averaged Nusselt numbers are also obtained. Topology analysis is applied to further understand the fluid flow and is used in analyzing the heat transfer characteristics.

It is found that the arrangement of side films positioned far from the center jets helps to enhance the flow disturbance and heat transfer behind the film holes. The heat transfer uniformity for the case of 55° films arrangement angle is most improved and the thermal performance is the highest in this study.

The film holes’ arrangements effects on fluid flow and heat transfer in an impingement cooled concave channel are conducted. The flow structures in the channel and flow characteristics near target by topology pictures are first obtained for the confined film cooled impingement cases. The heat transfer distributions are analyzed with the flow characteristics. The highest heat transfer uniformity and thermal performance situation is obtained in present work.

The pin fin is applied into a Lamilloy cooling structure which is broadly used in the leading edge region of the modern gas turbine vane. The purpose of this paper is to investigate effects of the layout, diameter and shape of pin fins on the flow structure and heat transfer characteristics in a newly improved Lamilloy structure at the leading edge region of a turbine vane.

A numerical method is applied to investigate effects of the layout, diameter and shape of pin fins on the flow structure and heat transfer characteristics in a newly improved Lamilloy structure at the leading edge of a turbine vane. The diverse locations of pin fins are Lp = 0.35, 0.5, 0.65. The diameter of the pin fins varies from 8 mm to 32 mm. Three different ratios of root to roof diameter for pin fins are also investigated, i.e. k = 0.5, 1, 2. The Reynolds number ranges from 10,000 and 50,000. Results of the flow structures, heat transfer on the target surface and pin fin surfaces, and friction factor are studied.

The heat transfer on the pin fin surface gradually decreases and then increases as the location of the pin fins increases. Increasing the diameter of the pin fins causes the heat transfer on the pin fin surface to gradually increase, while a lower value of the friction factor occurs. Besides, the heat transfer on the pin fin surface at a small root diameter increases remarkably, but a slight heat transfer penalty is found at the target surface. It is also found that both the Reynolds analogy performance and the thermal performance are increased compared to the baseline whose diameter and normalized location of pin fins are set as 16 and 0.5 mm, respectively.

The models provide a basic theoretical study to deal with nonuniformity of the temperature field for the turbine vane leading edge. The investigation also provides a better understanding of the heat transfer and flow characteristics in the leading edge region of a modern turbine vane.

This is a novel method to adopt pin fins into a Lamilloy cooling structure with curvature. It presents that the heat transfer of the pin fin surface in a pin-fin Lamilloy cooling structure with curvature can be significantly increased by changing the parameters of the pin fins which may lead to various flow behavior. In addition, the shape of the pin fin also shows great influence on the heat transfer and flow characteristics. However, the heat transfer of the target surface shows a small sensitivity to different layouts, diameter and shape of pin fin.

Maintaining the turbine blade’s temperature within the safety limit is challenging in high-pressure turbines. This paper aims to numerically present the conjugate heat transfer analysis of a novel approach to mini-channel embedded film-cooled flat plate.

Numerical simulations were performed at a steady state using SST k – ω turbulence model. Impingement and film cooling are classical approaches generally adopted for turbine blade analysis. The existing film cooling techniques were compared with the proposed design, where a mini-channel was constructed inside the solid plate. The impact of the blowing ratio (M), Biot number (Bi) and temperature ratio (TR) on overall cooling performance was also studied.

Overall cooling effectiveness was always shown to be higher for mini-channel embedded film-cooled plates. The effectiveness increases with increasing the blowing ratio from M = 0.3 to 0.7, then decreases with increasing blowing ratio (M = 1 and 1.4) due to lift-off conditions. The mini-channel embedded plate resulted in an approximately 21% increase in area-weighted average overall effectiveness at a blowing ratio of 0.7 and Bi = 1.605. The lower uniform temperature was also found for all blowing ratios at a low Biot number, where conduction heat transfer significantly impacts total cooling effectiveness.

To the best of the authors’ knowledge, this study presents a novel approach to improve the cooling performances of a film-cooled flat plate with better cooling uniformity by using embedded mini-channels. Despite the widespread application of microchannels and mini-channels in thermal and fluid flow analysis, the application of mini-channels for blade cooling is not explored in detail.

This paper aims to predict turbulent flow and heat transfer through different channels with periodic dimple/protrusion walls. More specifically, the performance of various low-Re k-ε turbulence models in prediction of local heat transfer coefficient is evaluated.

Three low-Re number k-ε turbulence models (the zonal k-ε, the linear k-ε and the nonlinear k-ε) are used. Computations are performed for three geometries, namely, a channel with a single dimpled wall, a channel with double dimpled walls and a channel with a single dimple/protrusion wall. The predictions are obtained using an in house finite volume code.

The numerical predictions indicate that the nonlinear k-ε model predicts a larger recirculation bubble inside the dimple with stronger impingement and upwash flow than the zonal and linear k-ε models. The heat transfer results show that the zonal k-ε model returns weak thermal predictions in all test cases in comparison to other turbulence models. Use of the linear k-ε model leads to improvement in heat transfer predictions inside the dimples and their back rim. However, the most accurate thermal predictions are obtained via the nonlinear k-ε model. As expected, the replacement of the algebraic length-scale correction term with the differential version improves the heat transfer predictions of both linear and nonlinear k-ε models.

The most reliable turbulence model of the current study (i.e. nonlinear k-ε model) may be used for design and optimization of various thermal systems using dimples for heat transfer enhancement (e.g. heat exchangers and internal cooling system of gas turbine blades).

This study aims to focus on the surface curvature, jet to target spacing and jet Reynolds number effects on the heat transfer and fluid flow characteristics of a slot jet impinging on a confined concave target surface at constant jet to target spacing.

Numerical simulations are used in this research. Jet to target spacing, H/B is varying from 1.0 to 2.2, B is the slot width. The jet Reynolds number, Rej, varies from 8,000 to 40,000, and the surface curvature, R2/B, varies from 4 to 20. Results of the target surface heat transfer, flow parameters and fluid flow in the concave channel are performed.

It is found that an obvious backflow occurs near the upper wall. Both the local and averaged Nusselt numbers considered in the defined region respond positively to the Rej. The surface curvature plays a positive role in increasing the averaged Nusselt number for smaller surface curvature (4-15) but affects little as the surface curvature is large enough (> 15). The thermal performance is larger for smaller surface curvature and changes little as the surface curvature is larger than 15. The jet to target spacing shows a negative effect in heat transfer enhancement and thermal performance.

The surface curvature effects are conducted by verifying the concave surface with constant jet size. The flow characteristics are first obtained for the confined impingement cases. Then confined and unconfined slot jet impingements are compared. An ineffective point for surface curvature effects on heat transfer and thermal performance is obtained.

The purpose of this paper is to study the condensation flow of wet steam in the last stage of a steam turbine and to obtain the distribution of condensation parameters such as nucleation rate, Mach number and wetness.

Because of the sensitivity of the condensation parameter distribution, a double fluid numerical model and a realizable k-ε-k_d turbulence model were applied in this study, and the numerical solution for the non-equilibrium condensation flow is provided.

The simulation results are consistent with the experimental results of the Bakhtar test. The calculation results indicate that the degree of departure from saturation has a significant impact on the wet steam transonic condensation flow. When the inlet steam deviates from the saturation state, shock wave interference and vortex mixing also have a great influence on the distribution of water droplets.

The research results can provide reference for steam turbine wetness losses evaluation and flow passage structure optimization design.

Numerical simulations are performed to determine the heat transfer characteristics of slot jet impingement of air on a concave surface. The purpose of this paper is to investigate the effect of protrusions on the heat transfer by placing semi-circular protrusions on the concave surface at several positions. After identifying appropriate locations where the heat transfer is a maximum, multiple protrusions are placed at desired locations on the plate. The gap ratio, curvature ratio (d/D) and the dimensions of the plate are varied so as to obtain heat transfer data. The curvature ratio is varied first, keeping the concave diameter (D) fixed followed by a fixed slot width (d). A surrogate model based on an artificial neural network is developed to determine optimum locations of the protrusions that maximize the heat transfer from the concave surface.

The scope and objectives of the present study are two-dimensional numerical simulations of the problem by considering all the geometrical parameters (H/d, d_p, Re, θ) affecting heat transfer characteristics with the help of networking tool and numerical simulation. Development of a surrogate forward model with artificial neural networks (ANNs) with a view to explore the full parametric space. To quantitatively ascertain if protrusions hurt or help heat transfer for an impinging jet on a concave surface. Determination of the location of protrusions where higher heat transfer could be achieved by using exhaustive search with the surrogate model to replace the time consuming forward model.

A single protrusion has nearly no effect on the heat transfer. For a fixed diameter of concave surface, a smaller jet possesses high turbulence kinetic energy with greater heat transfer. ANN is a powerful tool to not only predict impingement heat transfer characteristics by considering multiple parameters but also to determine the optimum configuration from many thousands of candidate solutions. A maximum increase of 8 per cent in the heat transfer is obtained by the best configuration constituting of multiple protrusions, with respect to the baseline smooth configuration. Even this can be considered as marginal and so it can be concluded that first cut results for heat transfer for an impinging jet on a concave surface with protrusions can be obtained by geometrically modeling a much simpler plain concave surface without any significant loss of accuracy.

The heat transfer during impingement cooling depends on various geometrical parameters but, not all the pertinent parameters have been varied comprehensively in previous studies. It is known that a rough surface may improve or degrade the amount of heat transfer depending on their geometrical dimensions of the target and the rough geometry and the flow conditions. Furthermore, to the best of authors’ knowledge, scarce studies are available with inclusion of protrusions over a concave surface. The present study is devoted to development of a surrogate forward model with ANNs with a view to explore the full parametric space.

The purpose of this paper is to enhance the heat transfer and thermal performance in the trailing edge region of the vane with vortex generators (VGs).

This numerical study presents the enhancement of thermal performance in the trailing part of a gas turbine blade. In the trailing part, generally, pin fins are used either in staggered or in-line arrangements to enhance the heat transfer. In this study, based on the idea from heat exchangers, pin fins are combined with VGs. A pair of VGs is embedded in the boundary layer upstream of each pin fin in the first row of the pin fin array having an in-line configuration. The effects of the VG angle relative to the streamwise direction and streamwise distance between the pin fin and VGs are investigated at various Reynolds numbers.

The results indicated that the endwall heat transfer is enhanced with the addition of VGs and the heat transfer from the surfaces of the pin fins. The level of heat transfer enhancement compared to the case without VGs is more significant at high Reynolds number. The surfaces of the VGs also show a significant amount of heat transfer. Study of the angle of the attack suggested that a high angle of attack is more appropriate for pin fin cooling enhancement whereas an intermediate gap between the VGs and pin fins shows considerable improvement of thermal performance compared to the small and large gaps. The phenomenon of heat transfer augmentation with the VGs is demonstrated by the flow field. It shows that the enhancement of heat transfer is governed by the mixing of the flow as a result of the interaction of vortices generated by the VGs and pin fins.

VGs are used to disturb the thermal boundary layer. It shows that heat transfer is augmented as a result of the interaction of vortices associated with VGs and pin fins.

The purpose of this paper is to study the effects of dimple geometries and arrangements on the heat transfer enhancement in a dimple jacketed heat exchanger.

For the purpose of this paper, with the experimental validated numerical model, this paper carries out numerical simulations of both single dimples with different geometries and the whole dimple jacketed heat exchanger with different dimple arrangements. For a single dimple, its secondary vortex flow, temperature differences and the pressure drop performance for different geometries are analyzed. For the whole dimple jacketed heat exchanger, the heat transfer and pressure drop performances are investigated by comparing the no dimple, triangular and rectangular dimple arrangements.

Results show that dimples can improve the heat transfer efficiency compared with conventional jacketed heat exchanger, and specific geometries and arrangement of dimples for better heat transfer performance are figured out.

This paper considers both dimple geometries and arrangements, which can be useful for further applications in specific integrated devices or similar applications.