Search results

This study aims at improving combustion process to reduce emissions. Emissions such as carbon monoxide, particulate matter and unburnt hydrocarbons are a result of incomplete combustion. These emissions have useful energy but cannot be reclaimed. Hence, to enhance combustion, effect of biofuel blending on diesel combustion was investigated.

Essential oils have been found easier for blending with diesel because of simple molecular structure compared to vegetable oils. Lavender oil is an essential oil which has not yet been studied by blending with diesel. The major constituents of lavender oil are linalyl acetate (cetane number improver) and linalool (nitrogen oxides reduction). A single-cylinder, four-stroke diesel engine was run by blending diesel with lavender oil (Lavandula angustifolia oil [LAO]) in varying proportions, 5%, 10% and 15% by volume.

Higher heat release rate (HRR) was observed using lavender oil blends compared to pure diesel. Compared to diesel, an increase in brake-specific fuel consumption using blends was observed. LAO15 has the lowest CO emissions at all loading conditions, 29.3% less at 100% load compared to diesel. LAO5 and LAO15 have 6.9% less HC emissions at 100% load condition compared to diesel. LAO15 has only 1.3% higher NO_x emissions compared to diesel at 100% load condition. LAO5 has the lowest smoke content at all loading conditions.

Lavender oil was used directly without any processing. Tested on single-cylinder engine.

To the best of the author’s knowledge, currently, there is no published work on lavender oil–diesel combination. Lavender oil can provide a simple renewable solution for diesel additives with potential up to 15% blending.

The study aims to verify and establish the result of the most suitable optimization approach for higher performance and lower emission of a variable compression ratio (VCR) diesel engine. In this study, three types of test fuels are taken and tested in a variable compression ratio diesel engine (compression ignition). The fuels used are conventional diesel fuel, e-diesel (85% diesel-15% bioethanol) and nano-fuel (85% diesel-15% bioethanol-25 ppm Al₂O₃). The effect of bioethanol and nano-particles on performance, emission and cost-effectiveness is investigated at different load and compression ratios (CRs). The optimum performance and lower emission of the engine are evaluated and compared with other optimization methods.

The test engine is run by diesel, e-diesel (85% diesel-15% bioethanol) and nano-fuel (85% diesel-15% bioethanol-25 ppm Al₂O₃) in three different loadings (4 kg, 8 kg and 12 kg) and CR of 14, 16 and 18, respectively. The optimum value of energy efficiency, exergy efficiency, NO_X emission and relative cost variation are determined against the input parameters using Taguchi-Grey method and confirmed by response surface methodology (RSM) technique.

Using Taguchi-Grey method, the maximum energy and exergy efficiency, minimum % relative cost variation and NO_X emission are 24.64%, 59.52%, 0 and 184 ppm, respectively, at 4 kg load, 18 CR and fuel type of nano-fuel. Using RSM technique, maximum energy and exergy efficiency are 24.8% and 62.9%, and minimum NO_X emission and % cost variation are 208.4 ppm and –6.5, respectively, at 5.2 kg load, 18 CR and nano-fuel. The RSM is suggested as the most appropriate technique for obtaining maximum energy and exergy efficiency, and minimum % relative cost; however, for lowest possible NO_X emission, the Taguchi-Grey method is the most appropriate.

Waste rice straw is used to produce bioethanol. 4-E analysis, i.e. energy, exergy, emission and economic analysis, has been carried out, optimized and compared.

Vast areas have been studied toward combustion and emission analysis in vegetable oil methyl esters and quite a few in algal oil biodiesel. To analyze the better alternate source for diesel engine, this study aims to investigate the combustion behavior and emission characteristics between cottonseed biodiesel and algal oil biodiesel on comparison with mineral diesel in a compression ignition engine.

The fuel properties like density, kinematic viscosity, calorific value and Cetane number have met the biodiesel standards for both algal and cottonseed biodiesel. At rated power, engine was operated on all three test fuels, where combustion analysis describing in-cylinder pressure, peak pressure, rate of pressure rise and rate of heat release and emission characteristics including hydrocarbon (HC), carbon monoxide (CO), oxides of nitrogen (NOx) and smoke for both biodiesel comparing mineral diesel.

Algal and cottonseed biodiesel showed up to 2-3°CA delayed start of combustion comparing mineral diesel curve. The in-cylinder pressure of algal biodiesel was found to be 68 bar, whereas cottonseed biodiesel exhibited 65 bar at full load condition. Similarly, the rate of pressure rise and rate of heat release of algal biodiesel depicted 7.9 and 10.7 per cent rise than cottonseed biodiesel, respectively. As the load increased, ignition delay showed decreasing trend, while combustion duration showed an increasing trend. HC, CO and smoke emissions were seen to be lower than mineral diesel with noticeable increase in NOx emission.

In this present investigation, biodiesel from Stoechospermum Marginatum, a marine marco algae, was used to fuel the compression ignition engine. Its combustion behavior and emission characteristics are compared with cottonseed biodiesel, a vegetable oil-based biodiesel having similar physio-chemical characteristics to understand the suitability of algal biodiesel in compression ignition engine. This study involves the assessment of straight biodiesel from macro algae and cottonseed oil on standard operating conditions.

This study aims to improve the performance and to regulate the harmful emission from the diesel engine. For this purpose, palm oil biodiesel (POBD), waste cooking biodiesel (WCBD) and animal fat biodiesel (AFBD) are used for examination.

The transesterification process was followed to convert the three raw oils into biodiesels and the experiments are conducted at various loads with fixed 25 rps. Diesel as a reference fuel and three neat biodiesels are tested for emissions and performance. By training the experimental results in an artificial neural network (ANN), the best biodiesel was predicted.

The biodiesels are tested for significant fuel properties with the American Society for testing and materials standards and observed that kinematic viscosity, density and cetane number are recorded higher than diesel fuel. The fatty acid composition (FAC) from chromatography reveals the presence of unsaturated FAC is more in POBD (70.89%) followed by WCBD (57.67%) and AFBD (43.13%). The combustion pressures measured at every degree of crank angle reveal that WCBD and AFBD exhibited on far with diesel fuel. Compared to diesel fuel WCBD and AFBD achieved maximum brake thermal efficiency of 31.99% and 30.93% at 75% load. However, there is a penalty in fuel consumption and NOx emissions from biodiesels. On the other hand, low carbon monoxide, unburnt hydrocarbon emissions and exhaust smoke are reported for biodiesels. Finally, WCBD was chosen as the best choice based on ANN modeling prediction results.

There is no evident literature on these three neat biodiesel applications with the mapping of ANN modeling.

Transport of people and goods has always been associated with the generation of some form of pollution, whether atmospheric, sound or visual. Managing the urban environment presents a major challenge: preserving environmental resources and also ensuring decent living conditions for the current population and for future generations. In the era of motorized and carbonized transport, vehicles are the main source of emission of atmospheric pollutants, mainly in large urban centers and important precursors of ozone. An important advance in minimizing vehicle emissions was the introduction of cleaner and additive fuels into the Brazilian market. The purpose of this paper is to study the effect of the Dienitro additive on the NO_x and CO emissions in buses of collective transport, Diesel S-50 exhaust gas recirculation (EGR) and S-10 with selective catalytic reduction (SCR) and EGR systems. Measurements of CO and NO_x gas emissions were carried out using a gas analyzer in S50 and S10 diesel buses with an EGR and SCR systems from a company operating in the collective transport of Biguaçu.

In this study, 20 measurements were performed without additives and 20 measurements with additivation in each bus, making it possible to calculate the average emission rate of CO and NO_x, pollutant gases with toxic effect.

The usage of Dienitro additive in diesel engines resulted in a significant reduction in the emission of polluting gases, carbon monoxide (CO) and nitrogen oxide (NO_x), thus being efficient in reducing the emissions of these gases.

The Dienitro additive was first tested on diesel engines by public transport buses, and there is great potential for reducing the emission of toxic gases.

The study aims to determine the the optimal value of output parameters of a variable compression ratio (CR) diesel engine are investigated at different loads, CR and fuel modes of operation experimentally. The output parameters of a variable compression ratio (CR) diesel engine are investigated at different loads, CR and fuel modes of operation experimentally. The performance parameters like brake thermal efficiency (BTE) and brake specific energy consumption (BSEC), whereas CO emission, HC emission, CO₂ emission, NO_x emission, exhaust gas temperature (EGT) and opacity are the emission parameters measured during the test. Tests are conducted for 2, 6 and 10 kg of load, 16.5 and 17.5 of CR.

In this investigation, the first engine was fueled with 100% diesel and 100% Calophyllum inophyllum oil in single-fuel mode. Then Calophyllum inophyllum oil with producer gas was fed to the engine. Calophyllum inophyllum oil offers lower BTE, CO and HC emissions, opacity and higher EGT, BSEC, CO₂ emission and NO_x emissions compared to diesel fuel in both fuel modes of operation observed. The performance optimization using the Taguchi approach is carried out to determine the optimal input parameters for maximum performance and minimum emissions for the test engine. The optimized value of the input parameters is then fed into the prediction techniques, such as the artificial neural network (ANN).

From multiple response optimization, the minimum emissions of 0.58% of CO, 42% of HC, 191 ppm NO_x and maximum BTE of 21.56% for 16.5 CR, 10 kg load and dual fuel mode of operation are determined. Based on generated errors, the ANN is also ranked for precision. The proposed ANN model provides better prediction with minimum experimental data sets. The values of the R² correlation coefficient are 1, 0.95552, 0.94367 and 0.97789 for training, validation, testing and all, respectively. The said biodiesel may be used as a substitute for conventional diesel fuel.

The blend of Calophyllum inophyllum oil-producer gas is used to run the diesel engine. Performance and emission analysis has been carried out, compared, optimized and validated.

Homogeneous charge compression ignition (HCCI) engine is an advanced combustion method to use alternate fuel with higher fuel economy and, reduce NOX and soot emissions. This paper aims to investigate the influence of ethanol fraction (ethanol plus gasoline) on dual fuel HCCI engine performance.

In this study, the existing CI engine is modified into dual fuel HCCI engine by attaching the carburetor to the inlet manifold for the supply of ethanol blend (E40/E60/E80/E100). The mixture of ethanol blend and the air is ignited by diesel through a fuel injector into the combustion chamber at the end of the compression stroke. The experiments are conducted for high load conditions on the engine i.e. 2.8 kW and 3.5 kW maximum output power for 1,500 constant rpm.

It is noticed from the experimental results that, with an increase of ethanol in the blends, ignition delay (ID) increases and the start of combustion is retarded. It is noticed that E100 shows the highest ID and low in-cylinder pressure; however, E40 shows the lowest ID compared to higher fractions of ethanol blends. An increase in ethanol proportion reduces NOX and smoke opacity but, HC and CO emissions increase compared to pure diesel mode engine. E100 plus diesel dual-fuel HCCI engine shows the highest brake thermal efficiency compared to remaining ethanol blends and baseline diesel engine.

This experimental study concluded that E100 plus diesel and E80 plus diesel gave optimum dual fuel HCCI engine performance for 2.8 kW and 3.5 kW rated power, respectively.

Compression ignition engines are being used in transportation, agricultural and industrial sectors due to its durability, fuel economy and higher efficiency. This paper aims to present investigation focuses on the utilization of nano additives in emulsified blends of Pongamia biodiesel and its impact on combustion, emission and performance characteristics of a diesel engine.

Pongamia biodiesel was produced through two-stage transesterification process. Taguchi method with L₉ Design of experiment was adopted to study the stability of fuel blends and 75 per cent diesel, 20 per cent biodiesel, 5 per cent water and 6 per cent of surfactant was found to be stable. Further, aluminum oxide nanoparticle was blended into the emulsified fuel in mass fraction of 100 ppm (D75-BD20-W5-S6-AO100) through ultrasonicating technique.

Oleic acid was found to be in prominent proportion in the Pongamia biodiesel. It was observed that D75-BD20-W5-S6 and D75-BD20-W5-S6-AO100 had the ability to produce lower in-cylinder pressure and rate of heat release compared to D100, B100 and D75-BD20 fuel blends. However, a higher rate of pressure rise was noticed in D75-BD20-W5-S6 and D75-BD20-W5-S6-AO100. Lower brake specific fuel consumption and relatively higher brake thermal efficiency were noticed in D75-BD20-W5-S6 and D75-BD20-W5-S6-AO100. Moreover, lower NO_x and smoke emission were also observed for nano-emulsified fuel blends.

Metal-based nano-additive significantly improved the physio-chemical properties of the fuel. Based on the literature, it is understood that emulsified biodiesel blend with nano enrichment using Pongamia biodiesel as base fuel was not carried out. Identifying a stable blend of diesel-biodiesel-water-nano additive using Taguchi’s design of experiments approach was an added value in formulating the test fuels. Furthermore, the formulated test fuel was compared with mineral diesel, biodiesel, and diesel-biodiesel blend to understand its suitability to use as a fuel in compression ignition (CI) engine.

Alternative sources for petroleum fuels have been the prime concern of most of the environmentalists. It is also a concern for economists due to the depletable nature of the fossil fuel. Vegetable oils are considered as good alternatives to diesel as their properties are close to diesel. This work aimed to produce a fuel by adding different proportions of de-oiled neem cake with diesel and to conduct experiments to find out its performance, emission and combustion characteristics.

At present, biodiesel is commercially produced from the vegetable oils by esterification processes. Because most of these oils are edible, its cost restricts the usage. The de-oiled cakes after crushing the seeds containing around 2 per cent of oil with less fatty materials are aimed in this study.

The fuel is prepared by adding dry neem de-oiled cake powder at different proportions ranging from 3 to 25 per cent by weight with diesel. Experimental results reveal that the fuel has the potential to reduce smoke, CO emissions simultaneously along with marginal increase in brake thermal efficiency.

In this published research work, the neem oil is used as biodiesel blends with diesel. Here, the authors have used neem de-oiled cake as a replacement for diesel.