Search results

This study aims to fabricate complex ceramic tetrahedron structures, which are challenging to produce by more conventional methods such as injection molding. To achieve this aim, thermoplastic-ceramic composite filaments were developed and printed with unmodified, consumer-grade, fused deposition modelling (FDM) printers instead.

Al₂O₃ ceramic powder was mixed with ethylene vinyl acetate polymer as a binder (50 Vol.- per cent) to form a filament with a constant diameter of 1.75 mm. After the printing and thermal treatment stages, the shrinkage and mechanical properties of cuboid and tetrahedron structures were investigated.

The shrinkage of the parts was found to be anisotropic, depending on the orientation of the printing pattern, with an increase of 2.4 per cent in the (vertical) printing direction compared to the (horizontal) printing layer direction. The alignment of the ceramic particle orientations introduced by FDM printing was identified as a potential cause of the anisotropy. This study further demonstrates that using a powder bed during the thermal debinding process yields sintered structures that can withstand twice the compressive force.

Ceramic FDM had previously been used primarily for simple scaffold structures. In this study, the applicability of ceramic FDM was extended from simple scaffolds to more complex geometries such as hollow tetrahedra. The structures produced in this study contain dense parts printed from multiple contiguous layers, as compared to the open structures usually found in scaffolds. The mechanical properties of the complex ceramic parts made by using this FDM technique were also subjected to investigation.

This study aims to explore a technique of metal additive manufacturing (MAM) for producing parts in aluminium. The proposed technique mimics the process of metal injection moulding but with the tools meant for fused freeform fabrication machines.

The work focusses on the preparation of novel feedstock by mixing the aluminium powder with binders made from different compositions of high-density polyethylene, paraffin wax, petroleum jelly and stearic acid. Further, a novel experimental setup with a paste extruder was designed to print the test samples. A sintering cycle was developed in-house along with a thermal debinding procedure. An experimental campaign was also carried with the proposed technique to establish a proof-of-concept. Produced samples were tested for part density, hardness, compressive strength and tensile strength.

The results indicate geometrical accuracy was an issue owing to the presence of petroleum jelly in the binder-powder mixture. Therefore, machining as a post-processing operation seems to be unavoidable. The study also elucidates that the printed specimen may require further heat treatment to replace wrought alloys. However, the sintered parts show hardness and compressive strength similar to that of wrought aluminium alloy.

The novelty of the work is to develop the cost effective and scalable powder extrusion-based MAM process for printing the aluminium parts.

The purpose of this paper is to compare different powder metallurgy (PM) processes to produce ceramic parts through additive manufacturing (AM). This creates the potential to rapidly shape ceramic parts with an almost unlimited shape freedom. In this paper, alumina (Al₂O₃) parts are produced, as Al₂O₃ is currently the most commonly used ceramic material for technical applications.

Variants of the following PM route, with indirect selective laser sintering (indirect SLS) as the AM shaping step, are explored to produce ceramic parts: powder synthesis, indirect SLS, binder removal and furnace sintering and alternative densification steps.

Freeform-shaped Al₂O₃ parts with densities up to approximately 90 per cent are obtained.

The resulting Al₂O₃ parts contain inter-agglomerate pores. To produce higher-quality ceramic parts through indirect SLS, these pores should be avoided or eliminated.

The research is innovative in many ways. First, composite powders are produced using different powder production methods, such as temperature-induced phase separation and dispersion polymerization. Second, four different binder materials are investigated: polyamide (nylon-12), polystyrene, polypropylene and a carnauba wax – low-density polyethylene combination. Further, to produce ceramic parts with increased density, the following densification techniques are investigated as additional steps of the PM process: laser remelting, isostatic pressing and infiltration.

The purpose of this paper is to assess a new powder metallurgy process to make alumina parts through indirect selective laser sintering (SLS). Density measurements, some geometrical assessments and scanning electron microscopy (SEM) microstructural analyses are performed after each stage of the process, allowing an objective overview to be provided of the challenges and possibilities for the processing of high density technical ceramic parts through SLS of ball milled alumina/polyamide powder agglomerates.

The powder production by ball milling, SLS, cold isostatic pressing (CIP) or quasi isostatic pressing (QIP), debinding and sintering (FS) stages of the powder metallurgy process were sequentially investigated.

Alumina parts with a density up to 94.1 per cent could be produced by a powder metallurgy process containing an SLS step. Microstructural investigation of the sintered samples reveals an alumina matrix with a grain size of ∼5 μm and two different kinds of pore morphologies, i.e. long elongated pores, which stem from the intergranular spacings during SLS, and intermediate pores, which likely originate from larger polyamide agglomerates in the ball milled powder. Also, QIPing at elevated temperatures is found to be a promising alternative for CIPing at room temperature to increase the final part density.

Cracks, long elongated pores and intermediate pores remained in the sintered parts. Homogenizing the microstructure of the parts through optimizing the composite starting powder, the deposition during SLS, the SLS parameters and QIPing parameters is essential to overcome these limitations.

Homogenizing the starting powder mixture and the microstructure of the SLS material is the key issue for producing ceramic parts through indirect SLS.

Indirect SLS of ceramics has hardly been reported and the combined use of SLS and QIPing is innovative in the field of indirect SLS of ceramics.

The purpose of this study is to investigate the effect of two unique processing routes (solvent jetting (SJ) and binder jetting (BJ)), on the green density of printed stainless steel 316L (SS316L) and Nickel (Ni) powders.

In the SJ processing route, a solvent is jetted unto the powder/binder mixture to selectively activate the binder, layer by layer. In the BJ processing route, a solution of the binder mixture is jetted onto the powder bed to selectively bind powder particles. The effects of printing parameters such as layer height, roller speed, shaker speed and nozzle temperature on the green density of printed components are investigated and compared for both processing routes.

Results show that layer height and nozzle temperature affect the relative density of the printed compact for both processing routes. Slightly higher relative densities were achieved via the SJ route, with the overall highest relative density being 42.7% at 100 µm layer height and 70% nozzle temperature for the SS316L components and 43.7% at 150 µm layer height and 90% nozzle temperature for the Ni components, respectively. Results also show an increase in the final sintered relative density with an increase in green (printed) relative density of the solvent jetted SS316L components, with the highest relative density being 87.2%.

The paper studies the influence of printing parameters on the green density of printed SS316L and Ni samples in an unprecedented effort to provide a comparative understanding of the process-property relationships in BJ and SJ of SS316L and Ni components to the additive manufacturing research community.

Fused filament fabrication (FFF) technique using metal filled filaments in combination with debinding and sintering steps can be a cost-effective alternative for laser-based powder bed fusion processes. The mechanical behaviour of FFF-metal materials is highly dependent on the processing parameters, filament quality and adjusted post-processing steps. In addition, the microstructural material properties and geometric characteristics are inherent to the manufacturing process. The purpose of this study is to characterize the mechanical and geometric performance of three-dimensional (3-D) printed FFF 316 L metal components manufactured by a low-cost desktop 3-D printer. The debinding and sintering processes are carried out using the BASF catalytic debinding process in combination with the BASF 316LX Ultrafuse filament. Special attention is paid on the effects of build orientation and printing strategy of the FFF-based technology on the tensile and geometric performance of the 3-D printed 316 L metal specimens.

This study uses a toolset of experimental analysis techniques [metallography and scanning electron microcope (SEM)] to characterize the effect of microstructure and defects on the material properties under tensile testing. Shrinkage and the resulting porosity of the 3-D printed 316 L stainless steel sintered samples are also analysed. The deformation behaviour is investigated for three different build orientations. The tensile test curves are further correlated with the damage surface using SEM images and metallographic sections to present grain deformation during the loading progress. Mechanical properties are directly compared to other works in the field and similar additive manufacturing (AM) and Metal Injection Moulding (MIM) manufacturing alternatives from the literature.

It has been shown that the effect of build orientation was of particular significance on the mechanical and geometric performance of FFF-metal 3-D printed samples. In particular, Flat and On-edge samples showed an average increase in tensile performance of 21.7% for the tensile strength, 65.1% for the tensile stiffness and 118.3% for maximum elongation at fracture compared to the Upright samples. Furthermore, it has been able to manufacture near-dense 316 L austenitic stainless steel components using FFF. These properties are comparable to those obtained by other metal conventional processes such as MIM process.

316L austenitic stainless steel components using FFF technology with a porosity lower than 2% were successfully manufactured. The presented study provides more information regarding the dependence of the mechanical, microstructural and geometric properties of FFF 316 L components on the build orientation and printing strategy.

The extrusion-based additive manufacturing method followed by debinding and sintering steps can produce metal parts efficiently at a relatively low cost and material wastage. In this study, 316L stainless-steel metal filled filaments were used to print metal parts using the extrusion-based fused filament fabrication (FFF) approach. The purpose of this study is to assess the effects of common FFF printing parameters on the geometric and mechanical performance of FFF manufactured 316L stainless-steel components.

The microstructural characteristics of the metal filled filament, three-dimensional (3D) printed green parts and final sintered parts were analysed. In addition, the dimensional accuracy of the green parts was evaluated, as well as the hardness, tensile properties, relative density, part shrinkage and the porosity of the sintered samples. Moreover, surface quality in terms of surface roughness after sintering was assessed. Predictive models based on artificial neural networks (ANNs) were used for characterizing dimensional accuracy, shrinkage, surface roughness and density. Additionally, the response surface method based on ANNs was applied to represent the behaviour of these parameters and to identify the optimum 3D printing conditions.

The effects of the FFF process parameters such as build orientation and nozzle diameter were significant. The pore distribution was strongly linked to the build orientation and printing strategy. Furthermore, porosity decreased with increased nozzle diameter, which increased mechanical performance. In contrast, lower nozzle diameters achieved lower roughness values and average deviations. Thus, it should be noted that the modification of process parameters to achieve greater geometrical accuracy weakened mechanical performance.

Near-dense 316L austenitic stainless-steel components using FFF technology were successfully manufactured. This study provides print guidelines and further information regarding the impact of FFF process parameters on the mechanical, microstructural and geometric performance of 3D printed 316L components.

This paper aims to investigate the vital characteristic of an innovative ceramic injection molding (CIM) process for orthopedic application with controlled porosity and improved tribological and mechanical properties which were affected by complex tribological interactions, whether lubricated like hip implants and other artificial prostheses. The main objective is to maximize the usage of palm stearin as a single based binder as the function of flow properties during injection molding process.

The binder used in this present study consists of 100 per cent palm stearin manufactured by Kempas Oil Sdn Bhd and supplied by Vistec Technology Sdn Bhd. The feedstock was prepared by using a Z-blade mixer (Thermo Haake Rheomix OS) and Brabender mixer model R2400. The feedstock prepared was injection molded using a manually operated vertical benchtop machine with an average pressure of about 5-7 bars. The firing step included the temporary holds at intermediate temperatures to burn out organic binders. At this stage, the green molded specimen was de-bound using a single-step wick-debinding method.

The maximum content of ceramic material is applied to investigate the efficiencies of net formulation that can be achieved by ceramic materials. The longer the viscosity will change with shear rate, the higher the value of n obtained instead. From the slope of the curves obtained in Figure 3, the value of n for the feedstock was determined to be less than 1, which indicates a pseudoplastic behavior and suitability for the molding process. Moreover, high shear sensitivity is important in producing complex and intrinsic specimens which are leading products in the CIM industry.

The feedstock containing HAp powder and palm stearin binder was successfully prepared at very low temperature of 70°C, which promoting a required pseudo-plastic behavior during rheological test. The single binder palm stearin should be optimized in other research works carried out, as palm stearin is most preferred compared to other polymeric materials that provided high energy consumption when subjected to the sintering process. Besides the binder is widely available in Malaysia, low cost and harmless effect during debinding process.

This paper aims to provide a comparison between the mechanical performance and microstructural aspects of stainless steel 17-4 PH processed using, respectively, two technologies: atomic diffusion additive manufacturing (ADAM) and metal fused filament fabrication (MFFF).

Different tensile specimens have been printed using an industrial system and a consumer three-dimensional (3D) printer, varying two main 3D printing parameters. Mechanical and microstructural tests are executed to make a comparison between these two technologies and two different feedstock material, to identify the main differences.

These 3D printing processes make parts with different surface quality, mechanical and microstructural properties. The parts, printed by the industrial system (ADAM), showed lower values of roughness, respect those produced using the 3D consumer printer (MFFF). The different sintering process parameters and the two debinding methods (catalytic or solvent based) affect the parts properties such as porosity, microstructure, grain size and amount of δ-ferrite. These proprieties are responsible for dissimilar tensile strength and hardness values. With the aim to compare the performances among traditional metal additive technology, MFFF and ADAM, a basic analysis of times and costs has been done.

The application of two metal extrusion techniques could be an alternative to other metal additive manufacturing technologies based on laser or electron beam. The low cost and printing simplicity are the main drivers of the replacements of these technologies in not extreme application fields.

Conventional machining methods for fabricating piezoelectric components such as ultrasound transducer arrays are time-consuming and limited to relatively simple geometries. The purpose of this paper is to develop an additive manufacturing process based on the projection-based stereolithography process for the fabrication of functional piezoelectric devices including ultrasound transducers.

To overcome the challenges in fabricating viscous and low-photosensitive piezocomposite slurry, the authors developed a projection-based stereolithography process by integrating slurry tape-casting and a sliding motion design. Both green-part fabrication and post-processing processes were studied. A prototype system based on the new manufacturing process was developed for the fabrication of green-parts with complex shapes and small features. The challenges in the sintering process to achieve desired functionality were also discussed.

The presented additive manufacturing process can achieve relatively dense piezoelectric components (approximately 95 per cent). The related property testing results, including X-ray diffraction, scanning electron microscope, dielectric and ferroelectric properties as well as pulse-echo testing, show that the fabricated piezo-components have good potentials to be used in ultrasound transducers and other sensors/actuators.

A novel bottom-up projection system integrated with tape casting is presented to address the challenges in the piezo-composite fabrication, including small curing depth and viscous ceramic slurry recoating. Compared with other additive manufacturing processes, this method can achieve a thin recoating layer (as small as 10 μm) of piezo-composite slurry and can fabricate green parts using slurries with significantly higher solid loadings. After post processing, the fabricated piezoelectric components become dense and functional.