Search results

To analyze the operating performance of an ac‐dc‐ac‐dc PWM parallel resonant converter operating at lagging power factor mode controlled based on fuzzy logic control method.

A range of published works relevant to dc‐ac‐dc converters and their control methods based on PWM technique are evaluated and their limitations in converter output voltage control are indicated in the first section of this paper. The Simulink model and different stages of the converter are described in the second section. In Section 3, the general mathematical model of the system is derived and the phase‐shift PWM switching technique is explained. The equivalent circuit of the high‐voltage high‐frequency transformer used in the converter and the effects of the transformer parameters on the converter operation are presented in Section 4. In Section 5, fuzzy logic control and the basic concepts of this method are described and its application to the proposed converter output voltage control is explained. In Section 6, the Simulink simulation results of the fuzzy logic control application are given for different operating conditions. In Section 7, an overview of the hardware used in this study is presented and the experimental results are given to show the performance of the controller. Finally, Section 8 gives the conclusions of the study.

The fuzzy logic control which is a suitable method for nonlinear systems such as the converter proposed in this paper, is successfully applied for output voltage control of the converter. The controller performance is satisfied. The phase‐shift angle of the converter is used as the control parameter. The paper also presents how the parasitic parameters of the transformer used in high‐voltage applications can be used as the circuit resonant elements.

In preparing this paper, the resources books and periodic journals existing in our university library and also the English resources relative to dc‐ac‐dc converters reachable through the internet were researched.

The suggested control method can be used in the control of linear and nonlinear systems. The study carried out in this paper is also a very good approach to be used in high‐voltage high‐frequency converters output voltage control.

Since, the control approach proposed in this paper does not require the information on converter and transformer parameters that affect the converter output voltage, so it can effectively be used in applications where there are parameter variation problems. The design of the transformer for the required load, finding an optimum operating frequency for the converter, and using the transformer parameters as resonant elements of the circuit to decrease the switching losses are the other contributions of this paper.

This paper aims to review comprehensively the different voltage-boosting techniques and classifies according to their voltage gain, stress on the semiconductor devices, count of the total components and their prominent features. Hence, the focus is on non-isolated step-up converters. The converters categorized are analyzed according to their category with graphical representation.

Many converters have been reported in recent years in the literature to meet our power requirements from mill watts to megawatts. Fast growth in the generation of renewable energy in the past few years has promoted the selection of suitable converters that directly impact the behaviour of renewable energy systems. Step-up converters are a fast-emerging switching power converter in various power supply units. Researchers are more attracted to the derivation of novel topology with a high voltage gain, low voltage and current stress, high efficiency, low cost, etc.

A comparative study is done on critical metrics such as voltage gain, switch voltage stress and component count. Besides, the converters are also summarized based on their advantages and disadvantages. Furthermore, the areas that need to be explored in this field are identified and presented.

Types of analysis usually performed in dc converter and their needs with the areas need to be focused are not yet completely reviewed in most of the articles. This paper gives an eyesight on these topics. This paper will guide the researchers to derive and suggest a suitable topology for the chosen application. Moreover, it can be used as a handbook for studying the various topologies with their shortfalls, which will provide a way for researchers to focus.

The purpose of this paper is to analyze the performance of LCLC resonant converter (RC) with proportional integral controller and fuzzy gain scheduled proportional integral controller.

The drawbacks of series RC and parallel resonant converter (PRC) are explained using relevant references in Section 1 of this paper. The necessity of RCs and the merits of zero voltage and zero current switching are given in the Section 2. In Section 3, the modeling of LCLC RC using state space technique is done. In Section 4, the open loop analysis and performance evaluation of proportional integral controller, fuzzy gain scheduled proportional controller using MATLAB Simulink is obtained. The hardware specification is given and experimental results are taken for LCLC RC. In Section 5, conclusion of study is given.

The LCLC RC overcomes the drawbacks of series and PRC. The fuzzy gain scheduled proportional integral controller is suitable for load variations in RC.

The output of the converter is not affected with the load variations since the controller suggested in the paper works for load changes and can be a solution for load parameter deviation applications. Also performance of the RC is improved by the fast response of the proposed controller.

This study aims to solve the problem that under light-load conditions, the output voltage regulation capability is lost due to the fact that the voltage gain of the LLC resonant converter does not decrease with the increase of the switching frequency.

In this paper, the impedance model considering the parasitic parameters of the primary and secondary sides is calculated under light-load conditions, the limitations of the previous method are explained and a new circuit improvement is proposed.

In this paper, an improved circuit is proposed, and the impedance Bode plot is used to verify that the circuit can effectively improve the voltage gain problem under light-load conditions. Finally, the experimental results verify the effectiveness of the proposed circuit through comparison with traditional solutions and circuits.

In this paper, the impedance model considering the parasitic parameters of the primary and secondary sides is calculated, the limitations of the previous method are explained and a new circuit improvement is proposed. When compared with the previous method, the proposed circuit improvement can suppress the voltage gain increase that occurs when the switching frequency increases to a certain level.

This paper aims to better design the resonant tank parameters for LLC resonant converter. And, it is found that under heavy load, the voltage gain is affected by junction capacitors of the primary side switching and the parasitic parameters of the secondary side diodes converted to the primary side, which will cause the voltage gain decreased when the switching frequency decreased.

This paper proposes an optimization parameters design method to solve this problem, which was based on impedance model considering the parasitic parameters of switching devices and diodes.

The effectiveness of the proposed method is verified by impedance Bode plots and experimental results.

From the perspective of impedance modeling, this paper finds the reasons for the insufficient voltage regulation capability of LLC resonant converters under heavy load and finds solutions through analysis.

This paper aims to solve the problems of large hard switching loss and unclear resonant parameter design in the existing inverter power supply topology.

This paper proposes a simple and reliable two-stage isolated inverter composed of series quasi-resonant push-pull and external freewheeling diode full-bridge inverter. The power supply topology is analyzed, the topology mode is analyzed, the mathematical model of the converter is established and the DC gain of the converter is deduced. The relationship between the load and the output gain of the resonant tank is presented, a new resonant parameter design method is proposed, and the parameter design of the resonant element of the converter is clarified.

The resonant components of the converter are designed according to the proposed resonant parameter design method, and the correctness of the method is verified by simulation and the development and testing of a 500 W experimental prototype. After experimental tests, the peak efficiency of the experimental prototype can reach 94%. Because the experimental prototype achieves soft switching, the heat generation of the switch is greatly reduced, so the heavy heat sink is removed, and the volume is reduced by about 30% compared with the traditional power supply, and the total harmonic distortion of the output voltage is about 2%.

The feasibility of the scheme is verified by experiments, which is of great significance for improving the efficiency of the inverter power supply and parameter optimization.

This paper aims to overcome the limitations of low efficiency, low power density and strong electromagnetic interference (EMI) of the existing pulsed melt inert gas (MIG) welding power supply. So a novel and simplified implementation of digital high-power pulsed MIG welding power supply with LLC resonant converter is proposed in this work.

A simple parallel full-bridge LLC resonant converter structure is used to design the digital power supply with high welding current, low arc voltage, high open-circuit voltage and a wide range of arc loads, by effectively exploiting the variable load and high-power applications of LLC resonant converter.

The efficiency of each converter can reach up to 92.3%, under the rated operating condition. Notably, with proposed scheme, a short-circuit current mutation of 300 A can stabilize at 60 A within 8 ms. Furthermore, the pulsed MIG welding test shows that a stable welding process with 280 A peak current can be realized and a well-formed weld bead can be obtained, thereby verifying the feasibility of LLC resonant converter for pulsed MIG welding power supply.

The high efficiency, high power density and weak EMI of LLC resonant converter are conducive to the further optimization of pulsed MIG welding power supply. Consequently, a high performance welding power supply is implemented by taking adequate advantages of LLC resonant converter, which can provide equipment support for exploring better pulsed MIG welding processes.

This paper aims to present an 8 kW LLC resonant converter designed for plasma power supply with higher efficiency and lighter structure. It presents how to solve the problems of large volume and weight, low performance and low efficiency of traditional plasma power supply.

At present, conventional silicon (Si) power devices’ switching performance is close to the theoretical limit determined by its material properties; the next-generation silicon carbide (SiC) power devices with outstanding advantages can be used to optimal design. This 8 kW LLC resonant converter prototype with silicon carbide (SiC) power devices with a modulated switching frequency ranges from 100  to 400 kHz.

The experimental results show that the topology, switching loss, rectifier loss, transformer loss and drive circuit of the full-bridge LLC silicon carbide (SiC) plasma power supply can be optimized.

Due to the selected research object (plasma power supply), this study may have limited universality. The authors encourage the study of high frequency resonant converters for other applications such as argon arc welding.

This study provides a practical application for users to improve the quality of plasma welding.

The experimental results show that the full-bridge LLC silicon carbide (SiC) plasma power supply is preferred in operation under conditions of high frequency and high voltage. And its efficiency can reach 98%, making it lighter, more compact and more efficient than previous designs.

Multi‐level diode‐clamped inverters have the challenge of capacitor voltage balancing when the number of DC‐link capacitors is three or more. On the other hand, asymmetrical DC‐link voltage sources have been applied to increase the number of voltage levels without increasing the number of switches. The purpose of this paper is to show that an appropriate multi‐output DC‐DC converter can resolve the problem of capacitor voltage balancing and utilize the asymmetrical DC‐link voltages advantages.

A family of multi‐output DC‐DC converters is presented in this paper. The application of these converters is to convert the output voltage of a photovoltaic (PV) panel to regulate DC‐link voltages of an asymmetrical four‐level diode‐clamped inverter utilized for domestic applications. To verify the versatility of the presented topology, simulations have been directed for different situations and results are presented. Some related experiments have been developed to examine the capabilities of the proposed converters.

The three‐output voltage‐sharing converters presented in this paper have been mathematically analysed and proven to be appropriate to improve the quality of the residential application of PV by means of four‐level asymmetrical diode‐clamped inverter supplying highly resistive loads.

This paper shows that an appropriate multi‐output DC‐DC converter can resolve the problem of capacitor voltage balancing and utilize the asymmetrical DC‐link voltages advantages and that there is a possibility of operation at high‐modulation index despite reference voltage magnitude and power factor variations.

Power converters are an integral part of the energy conversion process in solar photovoltaic (PV) systems which is used to match the solar PV generation with the load requirements. The increased penetration of renewable invokes intermittency in the generated power affecting the reliability and continuous energy supply of such converters. DC-DC converters deployed in solar PV systems impose stringent restrictions on supplied power, continuous operation and fault prediction scenarios by continuously observing state variables to ensure continuous operation of the converter.

A converter deployed for a mission-critical application has to ensure continuous regulated output for which the converter has to ensure fault-free operation. The fault diagnostic algorithm relies on the measurement of a state variable to assess the type of fault. In the same line, a predictive controller depends on the measurement of a state variable to predict the control variable of a converter system to regulate the converter output around a fixed or a variable reference. Consequently, both the fault diagnosis and the predictive control algorithms depend on the measurement of a state variable. Once measured, the available data can be used for both algorithms interchangeably.

The objective of this work is to integrate the fault diagnostic and the predictive control algorithms while sharing the measurement requirements of both these control algorithms. The integrated algorithms thus proposed could be applied to any converter with a single inductor in its energy buffer stage.

laboratory prototype is created to verify the feasibility of the integrated predictive control and fault diagnosis algorithm. As the proposed method combine the fault detection algorithm along with predictive control, a load step variation and manual fault creation methods are used to verify the feasibility of the converter as with the simulation analysis. The value for the capacitors and inductors were chosen based on the charge-second and volt-second balance equations obtained from the steady-state analysis of boost converter.