Search results

Describes methods of accelerated corrosion testing currently being used in the world today and the cabinets available in which to perform the tests. Compares the tests and looks at the results obtained from them, looking at constant salt‐spray testing ASTM B117, cyclic wet/dry Prohesion and the multi‐function automotive cyclic corrosion test which incorporates salt‐spray cycles and high humidity cycles. Gives test results comparing constant salt‐spray to cyclic Prohesion to natural outdoor exposure.

This study aims to propose a simple experimental method to distinguish the galvanic corrosion, crevice corrosion and self-corrosion in metal/carbon fiber reinforced polymer (CFRP) joints.

The corrosion behaviors of four different galvanic couples, whose anodes were Zn-coated DP590 steel and Al 6022, and cathodes were two kinds of CFRP, were investigated in immersion and GMW14872 cyclic conditions.

The results showed that the galvanic corrosion caused by direct contact between CFRP and metals was more serious than that caused by the jointing bolts. The corrosion damage caused by crevice corrosion was severer than that caused by galvanic corrosion. Self-corrosion was also significant, particularly under the cyclic salt spray condition.

Cyclic salt spray test may more reliably simulate the galvanic corrosion of a joint in industrial service environments, and real corrosion damage may be underestimated by a galvanic current measurement.

A deeper understanding of different corrosion mechanisms involved in CFRP/metal joints under different service conditions in industry has been given.

The purpose of this study is to investigate the effect of plasma pretreatment on the corrosion and adhesion behavior of Al coating deposited on iron steel by ion vapor deposition (IVD).

Ar plasma sputtering was carried out for 0, 5, 10 and 15 min, and then IVD Al coating was performed. Surface free energy measurements were conducted on the plasma-sputtered surfaces. Cross-sectional observations were carried out on the coating/substrate interface by using scanning electron microscopy. Corrosion resistance of the deposited films was characterized using potentiodynamic polarization curve test and electrochemical impedance spectroscopy (EIS).

Results demonstrated that surface free energy values were increased by increasing the sputtering time before coating process. The corrosion current density of the IVD Al coating deposited after 15 min Ar plasma pretreatment is three orders of magnitude lower than that of steel ST37 substrate. The EIS tests confirm the excellent anticorrosive properties of the Al-coated specimens.

With the increase in the plasma pretreatment time, coating adhesion would ameliorate because of the presence of plasma, which makes substrates a better place for Al ions to set and prevent any gap between coatings and substrates. This fact can be attributed to an increase in the surface free energy and reduction of contact angle of substrate exposed to plasma pre-treatment.

The Accrington Brick & Tile Co Ltd. It will be unusual to find a brick manufacturer exhibiting at the UK Corrosion Exhibition. But, The Accrington Brick & Tile Co Ltd is no ordinary brick maker. Its speciality is the design and manufacture of chemical resistant bricks, tiles, paver and other components including purpose‐made linings.

The purpose of this paper is to study the ability of commercial tara powder to convert rust into iron tannate and evaluate their use as raw material for the formulation of water based rust converter.

Water-borne acrylic primers were formulated with tara powder and aqueous tara extract and applied on steel rusted by three different methods. The conversion of rusted steel by tara tannins was studied by X-ray diffraction spectroscopy, infrared spectroscopy and scanning electron microscopy. The acrylic primers, containing hydrolysable tannins, were coated with alkyd finish and were evaluated in comparison to commercial systems in accelerated corrosion tests. The corrosion inhibition effects of tara powder on mild steel in 0.1M NaCl were studied by DC electrochemical techniques.

Tara tannin converts rust to ferric tannate and increases the magnetite content of rusted steel. The water-based acrylic primer formulated with aqueous extract of tara, alkyd-coated finish, showed performance equivalent to pure alkyd system.

The chlorides content in the commercial tara powder can be screened the beneficial effect of hydrolysable tannins to convert rust. Furthermore, the water-based rust converter formulated with acrylic resin may be sensitive to salt contamination of rust.

Hydrolysable tannins from commercial tara powder have not been studied yet in its application to the development of rust converters. A water-based primer formulated with commercial tara powder developed for the effective treatment of rusted surfaces can be of interest as an environmentally friendly to current commercial approaches.