Search results

This work aims to describe the face milling analysis on Inconel X-750 superalloy using coated carbides. The formed chips and tool wear were further analyzed at different cutting parameters. The various impact of cutting parameters on chip morphology was also analyzed. Superalloys, often referred to as heat-resistant alloys, have exceptional tensile, ductile and creep strength at high operating temperatures and good fatigue strength, and often better corrosion and oxidation resistance at extreme heat. Because of these qualities, these alloys account for more than half of the weight of sophisticated aviation, biomedical and thermal power plants today. Inconel X-750 is a high-temperature nickel-based superalloy that is hard to machine because of its extensive properties. At last, the discussion regarding the tool wear mechanism was analyzed and discussed in this article.

The machining parameters for the study are cutting speed, feed rate and depth of cut. One factor at a time approach was implemented to investigate the effect of cutting parameters on the cutting forces, surface roughness and material removal rate. The scatter plot was plotted between cutting parameters and target functions (cutting forces, surface roughness and material removal rate). The six levels of cutting speed, feed rate and depth of cut were taken as cutting parameters.

The cutting forces are primarily affected by the cutting parameters, tool geometry, work material etc. The maximum forces Fx were encountered at 10 mm/min cutting speed, 0.15 mm/rev feed rate and 0.4 mm depth of cut, further maximum forces Fy were attained at 10 mm/min cutting speed, 0.25 mm/rev feed rate and 0.4 mm depth of cut and maximum forces Fz were attained at 50 mm/min cutting speed, 0.05 mm/rev feed rate and 0.4 mm depth of cut. The maximum surface roughness value was observed at 40 mm/min cutting speed, 0.15 mm/rev feed rate and 0.5 mm depth of cut.

The effect of machining parameters on cutting forces, surface roughness, chip morphology and tool wear for milling of Inconel X-750 high-temperature superalloy is being less researched in the present literature. Therefore, this research paper will give a direction for researchers for further studies to be carried out in the domain of high-temperature superalloys. Furthermore, the different tool wear mechanisms at separate experimental trials have been explored to evaluate and validate the process performance by conducting scanning electron microscopy analysis. Chip morphology has also been evaluated and analyzed under the variation of selected process inputs at different levels.

This study aims to develop and evaluate an inexpensive and durable metal cutting wheel using thermal spraying and polymer binding to enhance the wheel’s cutting capability by bonding hard particles (abrasives) onto the wheel.

Thermal spraying was used to deposit the coating powder (chromium and silicon carbide) onto high carbon substrate. Wear loss and depth of cut as function of load, time and speed were evaluated on uncoated and coated wheel.

The coated cutting wheel performed better than the uncoated cutting wheel in terms of wear performance. However, the coated cutting wheel experienced coating peel off at higher load and cutting speed, leading to a decrease in wear resistance of the cutting wheel. Thus, optimally cutting should be performed either at low cutting speed and high load or at high cutting speed and low load to prolong the wheel’s lifetime.

The outcome of the study will be beneficial for academicians and industrial working on cutting wheel process.

Investigates the effects of the most influential cutting parameters (cutting speed, feed rate, depth of cut, tool nose radius, tool length and work piece length) on surface roughness quality and on the formation of built‐up edge in a lathe dry turning process of mild carbon steel samples. A full factorial design (384 experiments), taking into account the three‐level interactions between the independent variables has been conducted. The results show that the following three‐level interactions: feed rate × cutting speed × depth of cut, feed rate × cutting speed × tool nose radius and tool nose radius × depth of cut × tool length have significant effects on surface roughness in this type of machining operation. Shows that the analysis of main effects alone and even two‐level interactions could lead to a false interpretation of the results. The analysis of variance revealed that the best surface roughness is achieved with a low feed rate, a large tool nose radius and a high cutting speed. The results also show that the depth of cut has no significant effect on surface roughness when operating at cutting speeds higher than 160m/min. Furthermore, it is shown that built‐up edge formation deteriorates surface roughness when machining mild carbon steel at specific feed rate, tool nose radius and cutting speed levels. Proposes a new model for evaluating the limiting cutting speed to avoid the built‐up edge formation. Finally, shows through experimentation that an increase in depth of cut would lead to improved surface roughness when tool vibration is increased.

Even though austenitic stainless steels have been extensively used in industries, owing to some of the characteristics of the material, its performance in machining is difficult to understand, in particular at high cutting speeds. There is no availability of dependable and in-depth studies pertinent to this matter. In this work, performance of AISI 304 austenitic stainless steel was studied in terms of surface roughness (Ra) and material removal rate (MRR) at high cutting speeds. Subsequently, parametric optimization and prediction for responses were carried out.

Turning operations were conducted using L9 orthogonal array and the outcomes were analyzed to attain optimal set of machining parameters for the responses using signal-to-noise (S/N) ratio and Pareto analysis of variance (ANOVA). In the present work, the cutting speed values were considered beyond the recommended range as designated by tool manufacturers. Finally, multiple regression models were developed to predict responses.

From the results, 350 m/min was found to be a significant speed. The investigation reveals that even though the speeds are taken beyond the recommended values, the results are favorable. The optimal machining parameters values for surface quality obtained were cutting speed of 350 m/min, feed of 0.15 mm/rev and depth of cut of 2.0 mm. In case of MRR, the optimal values were: cutting speed of 400 m/min, feed of 0.25 mm/rev and depth of cut of 2.0 mm. It was found out that there was an improvement in Ra and MRR (around 15 and 4%) due to optimization. The results indicate that Pareto ANOVA is easier than S/N ratio. This revealed that the feed rate and depth of cut were mostly affected parameters for Ra and MRR. The developed models are capable of predicting the responses accurately.

The outcome of the work reveals that even though the speeds were taken beyond the recommended value, the results are favorable for manufacturing industries when the tool cost is considered insignificant.

No work was reported on machining of the chosen material beyond the recommended cutting speed. Moreover, it was observed from the past works that cutting speeds were limited to 100–300 m/min.

The knowledge over the performance of cutting fluids when applied under different machining conditions (such as distinct work material and cutting parameters) is critical in order to improve the efficiency of most machining operations. This paper is concerned with the performance of cutting fluids employed under two distinct machining operations involving aluminium alloys: drilling of AA 1050‐O aluminium applying cutting fluid as a mist and turning of AA 6262‐T6 aluminium alloy using cutting fluids (as a flood) with distinct extreme pressure additives (chlorine, sulphur and phosphor).

This work reports on a experimental study of the performance of cutting fluids when machining aluminium alloys.

The results indicated an increase in the flow rate of the mist led to lower feed forces but higher torque, power consumption and specific cutting pressure in the drilling operation (AA 1050‐O aluminium). The surface finish was not drastically affected by the cutting fluid flow rate. When turning AA 6162‐T6 aluminium alloy, in general, best results were observed using 10 per cent fluid concentration applied at the tool‐workpiece interface. The cutting fluid containing chlorine as extreme pressure additive produced lower cutting forces and better surface finish at high cutting speed and low feed rate and depth of cut.

The novel element of this paper is the use of minimal lubrication (drilling) and cutting fluids with distinct extreme pressure (turning).

The purpose of this paper is to form good cutting qualities in glass-epoxy material for opening flexible areas of rigid-flex printed circuit boards (PCB) by ultraviolet (UV) laser cutting.

The cut width and cut depth of glass-epoxy materials were both observed to evaluate their cutting qualities. The heat affected zone (HAZ) of the glass-epoxy material was also investigated after UV laser cutting. The relationships between the cut width and the parameters of various factors were analyzed using an orthogonal experimental design.

The cut width of the glass-epoxy material gradually increased with the increment of the laser power and Z-axis height, while cutting speed and laser frequency had less effect on the cut width. Optimal parameters of the UV laser process for cutting glass-epoxy material were obtained and included a laser power of 6W, a cutting speed of 170 mm/s, a laser frequency of 50 kHz and a Z-axis height of 0.6 mm, resulting in an average cut width of 25 μm and small HAZ.

Flexible areas of rigid-flex PCBs are in good agreement with the cutting qualities of the UV laser. The use of a UV laser process could have important potential for cutting glass-epoxy materials used in the PCB industry.

The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid.

The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism.

Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool

A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

The present study spotlights the single and multicriteria decision-making (MCDM) methods to determine the optimal machining conditions and the predictive modeling for surface roughness (Ra) and cutting tool flank wear (VB) while hard turning of AISI 4340 steel (35 HRC) under dry environment.

In this study, Taguchi L16 design of experiments methodology was chosen. The experiments were performed under dry machining conditions using TiSiN-TiAlN nanolaminate PVD-coated cutting tool on which Taguchi and responses surface methodology (RSM) for single objective optimization and MCDM methods like the multi-objective optimization by ratio analysis (MOORA) were applied to attain optimal set of machining parameters. The predictive models for each response and multiresponse were developed using RSM-based regression analysis. S/N ratios, analysis of variance (ANOVA), Pareto diagram, Tukey's HSD test were carried out on experimental data for profound analysis.

Optimal set of machining parameters were obtained as cutting speed: at 180 m/min., feed rate: 0.05 mm/rev., and depth of cut: 0.15 mm; cutting speed: 145 m/min., feed rate: 0.20 mm/rev. and depth of cut: 0.1 mm for Ra and VB, respectively. ANOVA showed feed rate (96.97%) and cutting speed (58.9%) are dominant factors for Ra and VB, respectively. A remarkable improvement observed in Ra (64.05%) and VB (69.94%) after conducting confirmation tests. The results obtained through the MOORA method showed the optimal set of machining parameters (cutting speed = 180 m/min, feed rate = 0.15 mm/rev and depth of cut = 0.25 mm) for minimizing the Ra and VB.

This work contributes to realistic application for manufacturing industries those dealing with AISI 4340 steel of 35 HRC. The research contribution of present work including the predictive models will provide some useful guidelines in the field of manufacturing, in particular, manufacturing of gear shafts for power transmission, turbine shafts, fasteners, etc.

The main purpose of this paper is to explore the use of solid lubricant during orthogonal machining of carbon steels. This is a pioneer work in Nigeria. Most works have been on oblique cutting using conventional oil as lubricants.

Different steels (low, medium and high carbon) were machined at different cutting conditions and tool geometries to determine the effects on surface characteristics while applying solid lubricant.

The results showed considerable improvement in the surface finish with the use of solid lubricant. There was also a decrease in surface roughness values as compared to wet machining.

Further works on solid lubricant's effects on cutting force and residual stress could be done.

From the findings of this work, solid lubricant use can be advocated as a better alternative to conventional cutting fluid. It is easily recoverable from the chips after machining.

So far, in Nigeria, solid lubricant has not been exploited as coolant during machining. This paper will be a platform for other researches on solid lubricants as coolant during cutting/machining in Nigeria.

The purpose of this paper is to investigate the performances of vegetable based cutting fluids by comparing tool life, surface roughness and cutting force during end milling of AISI 304 stainless steel. In the experiments, three different vegetable based cutting fluids developed from sunflower and canola oils (SCF‐II with 8% extreme pressure (EP), CCF‐II without EP and CCF‐II with 8% EP) and a commercial type of semi‐synthetic cutting fluid were used. Cutting fluid was applied to the cutting zone via two nozzles.

Effects of different cutting speeds (100, 150 and 200 m/min) and different feed rates (0.2, 0.25 and 0.3 mm/rev) on tool life, surface roughness and cutting force in milling of AISI 304 stainless steel were investigated. Depth of cut and step over were kept constant as 0.3 mm and 10 mm at both conditions, respectively.

Results indicated that CCF‐II with 8% EP cutting fluid showed better performance than the others.

In this study, effect of extreme pressure additive on milling performance was investigated.