Search results

During service period, due to the overload or other non-load factors, diagonal cracks of the pre-stressed concrete beam are seriously affecting the safety of the bridge structure. The purpose of this paper is to quickly realize the shear bearing capacity and shear stiffness through maximum width of the diagonal cracks and make correct judgments.

Through the shear failure test of four test beams, collecting data of diagonal cracks and shear stiffness loss value. According to the deformation curve of the shear stiffness, and combined with the calculation formula of the maximum width of diagonal cracks, the formula for calculating the effective shear stiffness based on the maximum width of diagonal cracks is deduced, then the results are verified by test data. Data regression method is used to establish the effective shear stiffness loss ratio calculation formula, the maximum width of diagonal cracks used as a variable factor, and the accuracy of this formula is verified by comparing the shear failure test results of pre-stressed hollow plates.

With the increase in width of the diagonal crack, the loss rate of shear stiffness of the concrete beams is initially fast and then becomes slow. The calculation formulae for shear stiffness based on the maximum width of the diagonal cracks were deduced, and the feasibility and accuracy of the formulae were verified by analysis and calculation of shear test data.

A method for quickly determine the shear stiffness loss of structures by using maximum width of the diagonal cracks is established, and using this method, engineers can quickly determine effective shear stiffness loss ratio, without complex calculations. So this method not only ensures the safety of human life, but also saves money.

The calculation of the crack width is necessary for the design of prestressed concrete (PC) members. The purpose of this paper is to develop a numerical model based on the bond-slip theory to calculate the crack width in PC beams.

Stress calculation method for common reinforcement after beam crack has occurred depends on the difference in the bonding performance between prestressed reinforcement and common reinforcement. A numerical calculation model for determining the crack width in PC beams is developed based on the bond-slip theory, and verified using experimental data. The calculation values obtained by the proposed numerical model and code formulas are compared, and the applicability of the numerical model is evaluated.

The theoretical analysis and experimental results verified that the crack width of PC members calculated based on the bond-slip theory in this study is reasonable. Furthermore, the stress calculation method for the common reinforcement is verified. Compared with the model calculation results obtained in this study, the results obtained from code formulas are more conservative.

The numerical calculation model for crack width proposed in this study can be used by engineers as a reference for calculating the crack width in PC beams to ensure the durability of the PC member.

The purpose of this paper is to add expanded perlite (EP) immobilized microorganisms that replace part of the standard sand in mortar to improve the self-healing ability of mortar cracks and reduce the water absorption of mortar after healing.

Bacillus pseudofirmus spores were immobilized with EP particles as self-healing agents. The effects of adding self-healing agents on the compressive strength of mortar specimens were observed. The ability of mortar specimens to heal cracks was evaluated using crack microscopic observation and water absorption experiments. The filler at the cracks was microscopically analyzed by scanning electron microscope and X-ray diffraction experiments.

First, the internal curing effect of EP promotes the hydration of cement in mortar, which generates more amount and denser crystal structure of Ca(OH)2 at mortar cracks and improves the self-healing ability of mortar. Second, the self-healing ability of mortar improves with the increase of self-healing agent admixture. Adding a self-healing agent of high admixture makes the planar undulation of calcite crystal accumulation at mortar cracks more significant. Finally, the initial crack widths that can be completely healed by adding EP and self-healing agents to the mortar are 200 µm and 600 µm, respectively.

The innovation points of this study are as follows. (1) The mechanism of the internal curing effect of EP particles on the self-healing ability of mortar cracks was revealed by crack microscopic observation tests and microscopic experiments. (2) The effect of different self-healing agent amounts on the self-healing ability of mortar cracks has been studied. (3) The effects of EP particles and self-healing agents on healing different initial widths were elucidated by crack microscopic observation tests.

The purpose of this paper is to find the geometry of a crack within a conductive plate and its parameters, on the basis of non-destructive testing, using eddy currents. The input data represents the measured values of magnetic flux density within the centre of the excitation coil.

The position of a crack can be determined by taking into consideration any change in the magnetic flux density between the measured points. The depth and width are determined through the use of a finite element model.

These calculations are the basis for determining a function that explains how magnetic flux density changes if the depth or width has changed. Jacobi's matrix is calculated using the determined functions’ analytical derivatives.

After wards, through the Newton-Raphson iterative procedure using the finite element method calculation results, the crack-depth and width can be obtained, this being one of the objectives in this paper. The suitability of the presented method was verified by the experimental example.

Incorporating pre-existing crack in service life prediction of reinforced concrete structures subjected to corrosion is crucial for accurate assessment, realistic modelling and effective decision-making in terms of maintenance and repair strategies.

An accelerated corrosion test was conducted by using impressed current method on cylindrical specimens with varying cover thickness and crack width. Mechanical properties of the specimens were evaluated by tensile tests.

The results show that, the pre-cracked samples exhibited shorter concrete cover cracking times, particularly with wider cracks when compared to the uncracked samples. Moreover, the load-bearing capacity of the reinforcement bars decreased owing to the pre-cracks, causing structural deflection and a shortened yield plateau. However, the ductility index remained consistent across all sample types, implying that the concrete had good overall ductility. Comparing the results of the non-corroded rebar and corroded rebar samples, the maximum reduction in the yield load was 25.22%, whereas the maximum reduction in the ultimate load was 26.23%. The simple mathematical model proposed in this study provides a reliable method for predicting the chloride ion diffusion coefficient in cracked concrete of existing reinforced concrete structures.

A simple mathematical model was proposed for evaluation of the equivalent chloride ion diffusion coefficient considering crack width, average crack spacing and crack extending lengths for cracked reinforced concrete structures, which is used to incorporate existing crack in service life prediction models.

The cracking of a reinforced concrete lining has a significant influence on the safety and leakage of pressure tunnels. This study aims to develop, validate and apply a numerical algorithm to simulate the lining cracking process during the water-filling period of pressure tunnels.

Cracks are preset in all lining elements, and the Mohr−Coulomb criterion with a tension cutoff is used in determining whether a preset crack becomes a real crack. The effects of several important factors such as the water pressure on crack surfaces (WPCS) and the heterogeneity of the lining tensile strength are also considered simultaneously.

The crack number and width increase gradually with the increase in internal water pressure. However, when the pressure reaches a threshold value, the increase in crack width becomes ambiguous. After the lining cracks, the lining displacement distribution is discontinuous and steel bar stress is not uniform. The measured stress of the steel bar is greatly determined by the position of the stress gauge. The WPCS has a significant influence on the lining cracking mechanism and should not be neglected.

A reliable algorithm for simulating the lining cracking process is presented by which the crack number and width can be determined directly. The numerical results provide an insight into the development law of lining cracks and show that the WPCS significantly affects the cracking mechanism.

A numerical simulation of the test beam was carried out with Abaqus and compared with test data to ensure that the modeling method is accurate. An analysis of the effects of the angle between the U-hoop and horizontal direction, the pre-crack height, the pre-crack spacing, and the strength of the geopolymer adhesive on the cracking load and ultimate load of the reinforced beam is presented.

Load tests and finite element simulations were conducted on carbon fiber reinforced polymer-reinforced concrete beams bonded with geopolymer adhesive. The bond-slip effect of geopolymer adhesive was taken into account in the model. The flexural performances, the flexural load capacities, the deformation capacities, and the damage characteristics of the beams were observed, and the numerical simulation results were in good agreement with the experimental results. An analysis of parametric sensitivity was performed using finite element simulation to investigate the effects of different angles between U-hoop and horizontal direction, pre-crack heights, pre-crack spacing, and strength of geopolymer adhesive on cracking load and ultimate load.

Under the same conditions, the higher the height of the pre-crack, the lower the bearing capacity; increasing the pre-crack spacing can delay cracking, but reduce ultimate load. By increasing the strength of the geopolymer adhesive, the flexural resistance of the beam is improved, and crack development is also delayed; the angle between the u-hoop and horizontal direction does not affect the cracking of reinforced beams; a horizontal u-hoop has a better effect than an oblique u-hoop, and 60° is the ideal angle between the u-hoop and horizontal direction for better reinforcement.

According to the experimental study in this paper, Abaqus was used to simulate the strength of different angles between U-hoop and horizontal direction, pre-crack heights, pre-crack spacings, and geopolymer adhesives, and the angles' effects on the cracking load and load carrying capacity of test beams were discussed. Since no actual tests are required, the method is economical. This paper offers data support for the promotion and application of environmentally friendly reinforcement technology, contributes to environmental protection, and develops a new method for reinforcing reinforced concrete beams and a new concept for finite element simulations.

There have been several recent cases reported in Malaysian newspapers of complaints about the impact of construction works on the physical conditions of the surrounding buildings. The purpose of this paper is to present the findings of a study conducted on a complaint received by the Local Authority in Selangor, Malaysia, about the impact of adjacent new construction works on the conditions of existing buildings in the neighbouring vicinity.

The sample case study consists of 28 units of two‐storey terrace houses, and the instrument used was the inspection form for building inspections. A building survey was carried out for all the buildings in the case study. Two teams conducted the survey. Each team was led by a professional building surveyor and assisted by two assistant building surveyors. Apart from basic surveying tools, a digital calliper was also used to measure cracks. Crack‐width data were collected and analysed using the statistical package for social sciences (SPSS) software.

The findings show that the adjacent new construction works have impacted the existing buildings nearby. A numbers of cracks of various magnitudes were identified in all the existing houses. One significant finding is that there appears to be no significant relationship between the cracks on the interior and the exterior, nor between the original and the renovated parts, of the existing buildings.

The significant number of cracks identified in the existing houses implies that the cracks were associated with the impacts from the new construction works. However, the primary cause of the building cracks was difficult to determine. It is therefore proposed that the Local Authority should establish guidelines at the local level for new construction works to prepare an inspection report on the condition of existing buildings in the surrounding area before the project commences. Building condition reports can then be used for reference in the event of claims received from the surrounding building owners alleging that the new construction works have adversely impacted the existing conditions of nearby buildings.

The structural behavior of reinforced concrete (RC) beams made with waste foundry sand (WFS) was examined in this study by using investigational data. Five RC beams were tested in this present work, four beams with varying WFS content and one beam with natural aggregates. The factors considered for studying the flexural performance of RC beams were WFS content (10%, 20%, 30% and 40%), 15% Ground Granulated Blast Furnace Slag (GGBS) is used as supplementary cementitious (SCM) content for all beams and tension reinforcement ratio (0.95%). The crack pattern of the RC beams with WFS (RCB1, RCB2, RCB3 and RCB4) was similar to that of referral beam–RCB0. The RC beams made with WFS (RCB1, RCB2, RCB3 and RCB4) show lesser number of cracks than referral beam–RCB0. It is observed that RCB1 beam shows higher ultimate moment carrying capacity than other RC beams. A detailed assessment of the investigational results and calculations based on IS: 456-2000 code for flexural strength exhibited that the present provisions conservatively predicts the flexural strength and crack width of RC beams with WFS and 15% GGBS. It is suggested that 10% WFS can be used to make RC beam.

In this present work, four RC beams made WFS and one RC beam made with natural aggregates. 15% GGBS is used as SCM for all RC beams. After casting of RC beams, the specimens were cured with wetted gunny bags for 28 days. After curing, RC beams like RCB0, RCB1, RCB2, RCB3 and RCB4 were tested under a four-point loading simply supported condition. An assessment of investigational results and calculations as per IS: 456-2000 code provisions has been made for flexural strength and crack width of RC beams with WFS and 15% GGBS. The crack pattern is also studied.

From this experimental results, it is found that 10% WFS can be used for making RC beam. The RCB1 with 10% WFS shows better flexural performance than other RC beams. RC beams made with WFS show lesser number of cracks than referral beam–RCB0. IS: 456-2000 code provisions can be safely used to predict the moment capacity and crack width of RC beams with WFS and 15% GGBS.

By utilization of WFS, the dumping of waste and environmental pollution can be reduced. By experimental investigation, it is suggested that 10% WFS can be used to make RC structural members for low cost housing projects.

The purpose of this paper is to discuss the durability and flexibility characteristics of latex modified ferrocement in comparison with conventional ferrocement particularly when exposed to severe environmental conditions.

The research programme encompasses the laboratory investigation on the structural, the deformation behaviour and characteristic of latex modified ferrocement elements cured in air and salt‐water environments. The tests include determination of load and deflection characteristics, moments, crack widths, crack spacing, and the number of cracks when subjected to static flexure.

Test result indicates a significant improvement in reducing and bridging micro cracks, especially in the pre‐peak load region. Fracture toughness and deformability increased significantly. However, the post peak behaviour was quite similar to conventional ferrocement.

The results show that latex modification has improved the mechanical properties of cement mortars, particularly their flexural strength.