Search results

This study aims to investigate the potential use of potato peel extracts as antibacterial finishes for cotton fabrics against Staphylococcus aureus and Escherichia coli. Potato peels are abundant as waste and provide a natural, cheaper and sustainable alternative means of preventing the spread of bacterial infections on cotton fabric.

This research included the characterization of potato peel extracts, application of the extract onto cotton fabric and efficacy testing of the treated cotton fabric against bacteria. Phytochemical screening, agar well diffusion antibacterial test, minimum inhibitory concentration and Fourier transform infrared (FTIR) tests were used to characterize the extract. Antibacterial efficacy of the treated fabric was determined qualitatively using the disc diffusion assay and quantitatively using the bacteria reduction test.

Phytochemical screening confirmed the presence of several secondary metabolites including phenols and flavonoids. Antibacterial tests revealed a positive response in Escherichia coli and Staphylococcus aureus with a zone of inhibition of 6.50 mm and 5.60 mm, respectively. Additional peaks on the FTIR spectroscopy confirmed the presence of potato peel extract on the treated cotton fabric. The treated cotton fabrics showed efficacy against Staphylococcus aureus and Escherichia coli up to 20 washes.

This study introduced the application of potato peel extracts onto cotton fabrics and assessment of the antibacterial properties before and after washing. Results of this study suggest that potato peel extracts can be used as an organic eco-friendly antibacterial finish for cotton fabrics.

The purpose of this study is to use liposome technology in the treatment of fabrics textiles because of its efficient energy saving, reducing time and temperature.

The newly prepared lecithin liposome was used to encapsulate dyes for the purpose of increasing dyeing affinity. Different ratios of commercially available lecithin liposomes (1%, 3%, 5% and 7%) were used simultaneously in the dyeing of cotton and wool fabrics. The treated fabrics (cotton and wool fabrics) were confirmed using different analytical procedures such as scanning electron microscope (SEM), Fourier-transition infrared spectroscopy, ultraviolet protection factor, colour strength (K|S) measurements and fastness measurements.

The results show that increasing liposome ratios in dyeing baths leads to increased dyeing affinity for cotton and wool fabrics compared with conventional dyeing without using liposomes. In addition to that, the colour strength values, infrared spectra, SEM and fastness properties of non-liposome-dyed fabrics and liposome-dyed fabrics were investigated.

The research paper provides broad spectrum of green encapsulation fabrics using liposome technology to perform the dye stability, dye strength and fastness.

This study aims to embed anatase, rutile and brookite TiO₂ nanoparticles (NPs) with different crystal phases into cotton fabrics by epoxy silane and to examine the effect of these applications on the photocatalytic and mechanical properties of the fabric.

Different aqueous dispersions which contain anatase, rutile and brookite were prepared at three different concentrations (5%, 10% and 15%). These NPs were embedded in cotton fabrics by using GPTS [(3-glycidyloxypropyl) trimethoxysilane]. Characterization tests were performed by scanning electron microscopy (SEM), Raman and Fourier-transform infrared spectroscopy (FT/IR). Samples were stained with methylene blue (MB) and then exposed to solar light for different periods. Color changes of the samples were examined with a spectrophotometer. Air permeability, abrasion and tear strength tests were applied to all samples.

According to SEM images, the NPs were successfully attached to the cotton fabrics, and epoxy silane coating surrounded the fiber surfaces. The presence of the coating was also confirmed by Raman spectroscopy and FT/IR. The treatments reduced the stainability of the samples. The most effective applications for ensuring photocatalytic activity in cotton fabrics were suspensions as 10% brookite, 10% anatase and 5% anatase, in descending order. The applied coating slightly reduced the samples’ air permeability, and wear and tear strength.

The importance of this study is to determine the optimal crystal phase and its concentration by using epoxy silane to ensure self-cleaning properties on cotton fabrics. The sample treated with 10% brookite is the most approached its original white color by 99.65% as a result of degradation of MB (after 120 min). On the other hand, using the pure rutile with epoxy silane was not suitable for removing MB from the fabric.

Through this study, four different types of woven fabric structures were created by using cotton/banana blends with a 70:30 ratio by varying the weaving specifications. This study aims to investigate the comfort and mechanical properties of these woven materials.

Taguchi L16 experimental design (5 factors and 4 levels) with response surface methodology tool was used to optimize mechanical and comfort characteristics. The yarn samples used in this study are cotton/banana with a blend ratio of 70:30. Fabric type (A), grams per square metre (GSM; B), yarn count (C), fabric thickness (D) and cloth cover factor (E) are the chosen process characteristics.

The highest tensile strength and tearing strength of the cotton/banana blended fabric samples were obtained as 326.3 N and 90.3 k.gf/cm, respectively. Similarly, the highest thermal conductivity and overall moisture management capacity values were found to be 0.6628 and 3.06 W/mK X10⁻⁴, respectively. The optimized process parameters for obtaining maximum mechanical properties were using canvas fabric structure, 182 GSM, 36^s Ne yarn count, 0.48 mm fabric thickness and 23.5 cloth cover factor. Similarly, the optimized process parameters for obtaining maximum comfort properties were achieved using a twill fabric structure, 182 GSM, 32^s Ne yarn count, 0.4 mm fabric thickness and 23 cloth cover factor.

In contrast to synthetic fabrics, banana fibre and its blended materials are significant ecological solutions for apparel and functional clothing. Products made from banana fibre are a sustainable and green alternative to conventional fabrics. Banana fibre obtained from the pseudostem of the plant has an appearance similar to ramie and bamboo fibres. Numerous studies showed that banana fibre could absorb significant moisture and be spun into yarn through ring and rotor spinning technology. On the other hand, this fibre can be easily combined with cotton, jute, wool and synthetic fibre. The present utilization of pseudostem of banana plant fibre is very minimal. This type of research improves the usability of bananas their blended fabrics as apparel and functional wear.

This paper aims to evaluate the effects of banana (Musa) peel and guava (Psidium guajava) leaves extract as mordants on jute–cotton union fabrics dyed with onion skin extract as a natural dye.

The dye was extracted from the outer skin of onions by boiling in water and later concentrated. The bio-mordants were prepared by maceration using methanol and ethanol. The fabrics were pre-mordanted, simultaneously mordanted and post-mordanted with various concentrations according to the weight of the fabric. The dyed and mordanted fabrics were later subjected to measurement of color coordinates, color strength and colorfastness to the washing test. Furthermore, the dyed samples were characterized by Fourier transform infrared, and different chemical bonds were analyzed by X-ray photoelectron spectroscopy analysis.

Significant improvement was obtained in colorfastness and color strength values in various instances using banana peel and guava leaves as bio mordants. Post-mordanted with banana peel provided the best results for wash fastness. Better color strength was achieved by fabric post-mordanted with guava leave extracts.

Sustainable dyeing methods of natural dyes using banana peel and guava leaves as bio mordants were explored on jute–cotton union fabrics. Improvement in colorfastness and color strength for various instances was observed. Thus, this paper provides a promising alternative to metallic salt mordants.

Titanium(IV) oxide nanoparticles (TiO₂ NP) were deposited to cotton denim fabrics using a self-crosslinking acrylate – a polymer dispersion to extend the lifetime of the products. This study aims to determine the optimum conditions to increase abrasion resistance, to provide self-cleaning properties of denim fabrics and to examine the effects of these applications on other physical properties.

The denim samples were first treated with nonionic surfactant to increase their wettability. Three different amounts of the polymer dispersion and two different pH levels were selected for the experimental design. The finishing process was applied to the fabrics with pad-dry-cure method.

The presence of the coatings and the adhesion of TiO₂ NPs to the surfaces were confirmed by scanning electron microscope and Fourier transform infrared spectroscopy analysis. It was ascertained that the most appropriate self-crosslinking acrylate amount and ambient pH level is 10 mL and “2”, respectively, for providing increased abrasion resistance (2,78%) and enhanced self-cleaning properties (363,4%) in the denim samples. The coating reduced the air permeability and softness of the denim samples. Differential scanning calorimetry and thermogravimetry analysis results showed that the treatments increased the crystallization temperatures and melting enthalpy values of the denim samples. Based on the thermal test results, it is clear that mass loss of the denim samples at 370°C decreased as the amount of self-crosslinking acrylate increased (at pH 3).

This study helped us to find out optimum amount of self-crosslinking acrylate and proper pH level for enhanced self-cleaning and abrasion strength on denim fabrics. With this finishing process, an environmentally friendly and long-life denim fabric was designed.

The essential properties of active sports fabrics are moisture management, quick-drying, body heat management and thermal regulations. Fibre type, blending nature, yarn and fabric structure and the finishing treatment are the key parameters that influenced the performance of the clothing meant for sportswear. This study aims to investigate the effect of fibre blending and structural tightness factors on bi-layer sport fabric's dimensional, moisture management and thermal properties.

In this study, 12 different bi-layer inter-lock fabrics were produced. Polyester filament (120 Denier) yarn was fed to form the backside of the fabric, and the face side was varied with cotton, modal, wool and soya spun yarns of 30sNe. Three different types of structural tightness factors were considered, such as low, medium and high were taken for sample development. The assessment towards dimensional, moisture management and thermal properties was carried out on all the samples.

The polyester-modal blend with a high tightness factor has shown maximum overall moisture management capability (OMMC) values of 0.73 and air permeability of 205.3 cm³/cm²/s. The same sample has shown comparatively higher thermal conductivity of 61.72 × 10^–3 W m^-1 °C^-1(Under compression state) and 58.45 × 10^–3 W m^-1 °C^-1 (under recovery state). In the case of surface roughness is concerned, polyester-modal blends have shown the lowest surface roughness, surface roughness amplitude and surface friction co-efficient. Among the selected fibre combinations, the overall comfort level of polyester-modal bi-layer knitted structure with a higher tightness factor is appreciable. Polyester-modal is more suitable for active sportswear among the four fiber blend combinations.

The outcome of this study will help to gain a better understanding of fibre blends, structural tightness factor and other process specifications for the development of bi-layer fabric for active sportswear applications. The dynamic functional testing methods (Moisture management and Thermal properties) were carried out to simulate the actual wearing environment of the sports clothing. This study will create a new scope of research opportunities in the field of bi-layer sports textiles.

This study was conducted to explore the influence of fibre blend and structural tightness factor on the comfort level of sportswear and to find the suitable fibre blend for active sportswear clothing.

Peanut skins are an agro-waste product with no commercial value. The purpose of this paper is to evaluate peanut skin as a natural dyestuff and to determine if this natural dye could be used in the dyeing of some Egyptian cotton cultivars.

The methodology consists of several steps; dye extraction procedure from peanut skin through aqueous extraction, then dyeing optimized using simultaneous mordanting using alum. Finally, dyed cotton has been subjected to different textile laboratory tests, for example, color measurements and mechanical properties. Color-fastness was determined on Egyptian cotton fabric. The peanut skin as a source of natural dye and the dyed cotton sample were characterized by fourier transform infrared spectroscopy (FTIR) analysis.

It was found that the natural dye extracted from peanut skin has an affinity for cotton samples and showed high dyeability with a unique color shade, good color strength and very good fastness.

The novelty of this paper is the extraction of color from the peanut's outer skin which is discarded as waste such as agro-waste of the agricultural process which can be used as a natural dye in the textile industry and applied to dyeing some Egyptian cotton fibers from different genotypes.

This study aims to promote sustainability-based education in fashion design and merchandising program to enhance students’ knowledge, skills and attitude about sustainability development, organizational responsibility and personal responsibility from the cotton industry perspective.

To conduct this study, three learning components were considered: learning from experts, learning by doing and outreach activity. Sustainability-related topics were strategically incorporated in different courses for one year; project-based learning approach was adopted; and pre–posttest survey was conducted to study the impact of sustainability-based education on student learning outcome. Rand’s principles-attributes matrix was applied to analyze the impact of sustainable education on student learning outcomes.

The results of course projects indicated enhanced student’s abilities on using use different types of cotton materials in product development, creative use of cotton in visual merchandising and development of business plans focused on sustainability. The two-group mean comparisons showed a significant positive impact on students’ knowledge in cotton and sustainability, followed by students’ skills and attitudes.

In response to the lack of systematic approach to incorporate sustainability-related topics in textile and apparel design discipline, this study offered an opportunity to involve approximately 110 students in various sustainability-based teaching and learning projects.

This paper aims to investigate the influence of picking sequence, weave design and weft yarn material on the thermal conductivity of the woven fabrics.

This work includes the development of 36 woven samples with two weave designs (1/1 plain and 3/1 twill), three picking sequences (single, double and three pick insertion) and six different weft yarn materials (cotton, polyester having 48 filaments, polyester with 144 filaments, spun coolmax having Lycra in core and coolmax in sheath, filament coolmax and polypropylene). The thermal conductivity was measured using ALAMBETA tester.

The results showed that weft yarn material, weave design and picking sequence have a meaningful impact on the thermal conductivity of woven fabric. The value of thermal conductivity was lowest for the fabrics with three pick insertion and 3/1 twill weave in all weft yarn materials.

Plain woven fabric with single pick insertion is feasible for summer wear to enhance the comfort of wearer. By changing the warp yarn grouping and material, improved thermal conductivity/resistance can also be achieved.

The authors have studied the combined effect of different weft yarn materials with different picking sequences and different weave designs on thermal conductivity of the woven fabrics.