Search results

The purpose of this paper is to investigate if copper nanoparticles could be utilized for two types of through hole plating in printed circuit boards, namely: as a catalytic material to initiate the electroless copper deposition process; and as a “conductive” layer which is coherent and conductive enough to allow “direct” electroplating of the through hole. The employment of nanoparticles means that an effective method of dispersion is required and this paper studies the use of mechanical agitation and ultrasound for this purpose.

The paper utilized drilled, copper clad FR4 laminate. The through holes were functionalized using a commercially available “conditioner” before being immersed in a solution of copper nanoparticles which were dispersed using either a magnetic stirrer or ultrasound (40 kHz). When the copper nanoparticles were utilized as a catalytic material for electroless copper plating, the efficacy of the technique was assessed using a standard “backlight” test which allowed the plating coverage of the through holes to be determined. As a control, a standard palladium catalysed electroless copper process was employed. The morphology of the electroless copper deposits was also analysed using scanning electron microscopy. In the “direct plate” approach, after immersion in the copper nanoparticle dispersion, the through holes were electroplated at 3 Adm⁻² for 15 min, sectioned and examined using an optical microscope. The distance that the copper electroplate had penetrated down the through hole was then determined.

The paper has shown that copper nanoparticles can be used as a catalytic material for electroless copper plating. The coverage of the electroless copper in the through hole improves as the copper nanoparticle concentration increases and, at the highest copper nanoparticle concentrations employed, good, but not complete, electroless copper coverage is obtained. Dispersion of the copper nanoparticles using ultrasound is critical to the process. Ultrasonically dispersed copper nanoparticles achieve some limited success as a conductive layer for “direct” electroplating with some penetration of the electroplated deposit into the through hole. However, if mechanical agitation is employed to mix the nanoparticles, no through hole plating obtaines.

The paper has demonstrated the “proof of concept” that copper nanoparticles can be utilized to catalyse the electroless copper process, as well as their potential to replace costly palladium‐based activators. The paper also illustrates the potential for copper nanoparticles to be used as a “direct plate process” and the necessity for using ultrasound for their dispersion in either process.

The purpose of this paper is to investigate the influence of silver nanoparticle additions on the wetting properties of Sn‐Ag‐Cu (SAC) solder paste. In this investigation, the basic solder paste contained 85 wt.% of commercial Sn 96.5 Ag 3 Cu 0.5 powder (with the particle sizes in the range of 20‐38 μm) and 15 wt.% of self‐prepared middle activated rosin flux. To this paste was added 0.5, 1, 2 and 4 wt.% of self‐prepared silver nano‐powders of different grain sizes (from 9 to 138 nm). After the pastes had stabilized, their wetting properties were tested. The main goal of these investigations was to improve the wetting properties of SAC solder paste and to find correlations between the results of the wetting of solder paste with nanoparticles on the copper substrate with the microstructure of the solder joints.

The following methods were applied for the wetting solder paste investigation: spreading on the copper substrate, contact angle measurement on the copper and wetting on a FR‐4 laminate double sided with an 18‐μm thick copper foil. The investigations were performed at temperatures of 220, 230, 240 and 250°C. Cross‐sectioning was performed on the solder paste after reflow on the copper substrate. For the microstructural analysis of the “nano” modified solder joints obtained at 250°C, standard metallographic procedures were applied. Changes in the microstructure, the thickness of the inter‐metallic compounds (IMCs) and their chemical compositions were observed by means of scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS).

As expected, a higher silver nanoparticle addition to the SAC solder paste resulted in better wetting properties on copper. The results indicated the possibility of an improvement of the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature. An improvement was also observed in the wettability with a decrease in the silver nanoparticle grain size. Also, the wettability proceeded at a lower temperature (20°C lower) than that for the SAC paste, without the nano‐additives. For the 4 per cent silver nanoparticle addition, Ag₃Sn star‐like IMCs were also found, which grew with the lowering of the silver nanoparticle grain size.

Further studies are necessary for confirmation of the practical application, especially of the mechanical properties, as well as the reliability properties of the solder joints, for the chosen solder paste with silver nanoparticles.

Taking into account the wetting data, the best results of the “nano” SAC solder pastes were obtained for the highest addition of the silver nanoparticles. It was found that the spreading on copper was higher and the contact angles were lower for the SAC solder paste with 4 per cent (by wt.) of 138‐nm grain size silver nanoparticles. A comparison of SAC solder pastes with a 4 per cent silver nanoparticle addition but of a different grain size (138‐9 nm), suggested a further improvement in wetting properties with lowering of the silver nanoparticle grain size. The results suggested the possibility of an improvement in the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature.

Spreading, wetting and contact angle measurement methods were used for the wetting determination of the SAC solder paste with the silver nanoparticles on copper under the same temperature conditions. Also, the microstructure of the solder joints obtained at 250°C was determined with the use of SEM and EDS methods. The results obtained made it possible to draw conclusions regarding the correlation between the output of the wetting results and the amount and the grain size of the added silver nanoparticles, and also the microstructure and thickness of the IMCs of the “nano” solder joints.

The purpose of this paper is to investigate the possibility of using the iron nanoparticles and iron nanoparticles coated with copper layer as additives to base oils.

Fe and Fe+Cu nanoparticles were synthesized by a reduction modification method and added to mineral oil. The size and structure of prepared nanoparticles were characterized by SEM, TEM, XRF, AAS and XRD analysis. Tribological properties of modified lubricants were evaluated on a four‐ball machine in a model of sliding friction pairs.

Spectral and microscopy analysis evidently displayed the formation of Fe and Fe+Cu nanoparticles in suspensions of colloidal solutions and oil. The size of formed nanoparticles was in 15‐50 nm range. Tribological experiments show good lubricating properties of oils modified with Fe and Fe+Cu nanoparticles: higher wear resistance (55 per cent and 46 per cent accordingly) and lower friction coefficient (30 per cent and 26 per cent accordingly). The tests show that nanoparticles provide decreasing tendency of friction torque during the operation of friction pair.

The paper demonstrates that iron nanoparticles and iron nanoparticles coated with copper layer, not only reduce the wear and friction decrease of friction pairs, but possibly also can create layer in oil which separates two friction surfaces and have some self‐organisation properties.

This study aims to investigate the numerical analysis of mixed convection within the horizontal annulus in the presence of water-based fluid with nanoparticles of aluminum oxide, copper, silver and titanium oxide. Numerical solution is performed using a finite-volume method based on the SIMPLE algorithm, and the discretization of the equations is generally of the second order. Inner and outer cylinders have a constant temperature, and the inner cylinder temperature is higher than the outer one. The two cylinders can be rotated in both directions at a constant angular velocity. The effect of parameters such as Rayleigh, Richardson, Reynolds and the volume fraction of nanoparticles on heat transfer and flow pattern are investigated. The results show that the heat transfer rate increases with the increase of the Rayleigh number, as well as by increasing the volume fraction of the nanoparticles, the heat transfer rate increases, and this increase is about 8.25 per cent for 5 per cent volumetric fraction. Rotation of the cylinders reduces the overall heat transfer. Different directions of rotation have a great influence on the flow pattern and isotherms, and ultimately on heat transfer. The addition of nanoparticles does not have much effect on the flow pattern and isotherms, but it is quantitatively effective. The extracted results are in good agreement with previous works.

Studying mixed convection heat transfer in the horizontal annulus in the presence of a water-based fluid with aluminum oxide, copper, silver and titanium oxide nanoparticles is carried out quantitatively using a finite-volume method based on the SIMPLE algorithm.

Increasing the Rayleigh number increases the Nusselt number. Increasing the Richardson number increases heat transfer. Adding nanoparticles does not have much effect on the flow pattern but is effective quantitatively on heat transfer parameters. The addition of nanoparticles sometimes increases the heat transfer rate by about 8.25 per cent. In constant Rayleigh numbers, increasing the Reynolds number reduces heat transfer. The Rayleigh and Reynolds numbers greatly affect the isotherms and streamlines. In addition to the thermal conductivity of nanoparticles, the thermo-physical properties of nanoparticles has great effect in the formation of isotherms and streamlines and ultimately heat transfer.

Studying the effect of different direction of rotation on the isotherms and streamlines, as well as the comparison of different nanoparticles on mixed convection heat transfer in annulus.

The current study is mainly motivated by the need to the development of the transient MHD mixed convection stagnation-point flow and heat transfer of an electrically conducting nanofluid over a vertical permeable stretching/shrinking sheet by means of Tiwari-Das nanofluid model. The purpose of this paper is to investigate the effects of the parameters governing the flow i.e. the nanoparticle volume fraction, the unsteadiness parameter, the magnetic parameter, the wall transpiration parameter, the mixed convection parameter and the velocity ratio parameter on dimensionless velocity and temperature distributions, skin friction coefficient and local Nusselt number.

The mathematical model has been formulated based on Tiwari-Das nanofluid model. Three different types of water-based nanofluid with copper, aluminum oxide (alumina) and titanium dioxide (titania) as nanoparticles are considered in this investigation. Using appropriate similarity variables, the governing equations are transformed into nonlinear ordinary differential equations in the dimensionless stream function, which is solved analytically by the well-know homotopy analysis method. The present simulations agree closely with the previous studies in the especial cases.

The results show that by increasing the nanoparticle volume fraction, the unsteadiness parameter, the magnetic parameter, the wall transpiration parameter, the mixed convection parameter or reducing the velocity ratio parameter, the skin friction coefficient enhances. Furthermore, the local Nusselt number enhances with different rates by increasing the nanoparticle volume fraction, the unsteadiness parameter, the magnetic parameter, the wall transpiration parameter, the mixed convection parameter and the velocity ratio parameter. Besides, the skin friction coefficient and the local Nusselt number are highest for copper-water nanofluid compared to the alumina-water and titania-water nanofluids.

Tiwari-Das nanofluid model has not been applied for the flow with these characteristics as mentioned in the paper. A comprehensive survey on boundary layer behavior has been presented. There are few studies regarding as analysis on thermal and hydrodynamics boundary layer. All plots presented in the paper are new and did not report in any other study. The effects of the parameters governing the flow on skin friction coefficient and local Nusselt number have been illustrated in the paper while there are some conflicts with previous published article that have been interpreted in details in the paper.

In the developing field of nano-materials synthesis, copper oxide nanoparticles (NPs) are deemed to be one of the most significant transition metal oxides because of their intriguing characteristics. Its synthesis employing green chemistry principles has become a key source for next-generation antibiotics attributed to its features such as environmental friendliness, ease of use and affordability. Because they are more environmentally benign, plants have been employed to create metallic NPs. These plant extracts serve as capping, stabilising or hydrolytic agents and enable a regulated synthesis as well.

Organic chemical solvents are harmful and entail intense conditions during nanoparticle synthesis. The copper oxide NPs (CuO-NPs) synthesised by employing the green chemistry principle showed potential antitumor properties. Green synthesised CuO-NPs are regarded to be a strong contender for applications in the pharmacological, biomedical and environmental fields.

The aim of this study is to evaluate the anticancer potential of CuO-NPs plant extracts to isolate and characterise the active anticancer principles as well as to yield more effective, affordable, and safer cancer therapies.

This review article highlights the copper oxide nanoparticle's biomedical applications such as anticancer, antimicrobial, dental and drug delivery properties, future research perspectives and direction are also discussed.

The purpose of this study is to analyze an unsteady MHD Darcy flow of nonNewtonian hybrid nanoliquid past an exponentially accelerated vertical plate under the influence of velocity slip, Hall and ion slip effects in a rotating frame of reference. The fluids in the flow domain are assumed to be viscously incompressible electrically conducting. Sodium alginate (SA) has been taken as a base Casson liquid. A strong uniform magnetic field is applied under the assumption of low magnetic Reynolds number. Effect of Hall and ion-slip currents on the flow field is examined. The ramped heating and time-varying concentration at the plate are taken into consideration. First-order homogeneous chemical reaction and heat absorption are also considered. Copper and alumina nanoparticles are dispersed in base fluid sodium alginate to be formed as hybrid nanoliquid.

The model problem is first formulated in terms of partial differential equations (PDEs) with physical conditions. Laplace transform method (LTM) is used on the nondimensional governing equations for their closed-form solution. Based on these results, expressions for nondimensional shear stresses, rate of heat and mass transfer are also determined. Graphical presentations are chalked out to inspect the impacts of physical parameters on the pertinent physical flow characteristics. Numerical values of the shear stresses, rate of heat and mass transfer at the plate are tabulated for various physical parameters.

Numerical exploration reveals that a significant increase in the secondary flow (i.e. crossflow) near the plate is guaranteed with an augmenting in Hall parameter or ion slip parameter. MHD and porosity have an opposite effect on velocity component profiles for both types of nanoliquids. Result addresses that both shear stresses are strongly enhanced by the Casson effect. Also, hybrid nanosuspension in Casson fluid (sodium alginate) exhibits a lower rate of heat transfer than usual nanoliquid.

This model may be pertinent in cooling processes of metallic infinite plate in bath and hybrid magnetohydrodynamic (MHD) generators, metallurgical process, manufacturing dynamics of nanopolymers, magnetic field control of material processing, synthesis of smart polymers, making of paper and polyethylene, casting of metals, etc.

The originality of this study is to obtain an analytical solution of the modeled problem by using the Laplace transform method (LTM). Such an exact solution of nonNewtonian fluid flow, heat and mass transfer is rare in the literature. It is also worth remarking that the influence of Hall and ion slip effects on the flow of nonNewtonian hybrid nanoliquid is still an open question.

This study aims to investigate the impact of surface waviness on the static performance parameters of hydrodynamic journal bearings operating with lubricants containing copper oxide (CuO) and cerium oxide (CeO₂) nanoparticles.

The static performance parameters of bearings with surface waviness and the addition of nanoparticles in lubricants were calculated using the nondimensional form of Reynolds equation and finite element method. Static performance parameters are calculated at different waviness numbers in the circumferential, axial and both directions at various wave amplitudes with variable viscosities of lubricants with nanoparticles using the viscosity equation forming a relationship between the relative viscosity, temperature and weight fraction of nanoparticles in lubricant developed from the experimental results.

The computed results indicate that the impact of waviness on the bearing surface enhances the load capacity, reduces friction coefficient, and is more effective in the circumferential direction than in the axial direction or in both directions. The addition of CuO and CeO₂ to the lubricant enhanced its viscosity which further improved the steady-state parameters of the wave bearing.

This study is based on a numerical technique, which has significant limitations, and the simulated results must be tested experimentally.

The current findings will be beneficial for designers to improve the performance of hydrodynamic journal bearings.

The calculated results demonstrate that the combined effect of the surface waviness on bearings and the addition of nanoparticles to lubricants can greatly increase the performance of hydrodynamic journal bearings.

Studies on this topic have shown the remarkable lubricating properties, viz. friction-reducing and anti-wear, of certain nanoparticles. This makes them potential candidates for replacing the lubrication additives currently used in automobile lubricants, especially because the latter is known to be pollutants and less efficient in some specific conditions. This has not gone unnoticed to professionals in the sector, including those commercializing these additives, the oil companies and the car industry, all of whom are following this burgeoning research area with keen interest. All of them are faced with the problem of providing lubricants that meet the needs of the technological evolution of engines while respecting ever-stricter environmental norms.

The impact of copper oxide (CuO) and zinc oxide (ZnO) nanoparticles on the tribological properties of the SAE-40 pure diesel oil is studied in this paper. The two nanoparticles are not oxide or deteriorate with the base oil. The average size of CuO and ZnO nanoparticles is 40 and 20 nm, respectively. Nanoparticle concentrations of 0.1 Wt.%, 0.2 Wt.%, 0.3 Wt.%, 0.4 Wt.% and 0.5 Wt.% are tested using a pin-on-disk tribometer to evaluate their impact on friction and wear. The test is carried out at different loads and rotating speeds of 58.86 N and 300 rpm, 39.24 N and 500 rpm and 78.48 N and 900 rpm at room temperature, respectively.

The obtained results of the nanolubricants are compared with those of pure diesel oil in terms of % improvement in tribological properties. However, it is observed that an increase in the nanoparticle concentrations does not guarantee to enhance the tribological properties. Similarly, increasing the applied load and the rotating speed does not lead to improving the anti-friction and anti-wear properties. The results obtained revealed that the optimal improvements in the anti-friction and anti-wear properties of the pure oil are 69% and 77% when CuO nanoparticle concentrations of 0.3 Wt.% and the ZnO nanoparticle concentrations of 0.1 Wt.% are used, where the applied load and rotating speed are 39.24 N and 500 rpm, respectively. It has also been noticed that the CuO nanolubricants have a significant impact on the anti-friction property compared with ZnO nanolubricants.

All these nanoparticles have been the subject of detailed investigation in this research and many key issues have been tackled, such as the conditions leading to these properties, the lubrication mechanisms coming into play, the influence of parameters such as size, structure and morphology of the nanoparticles on their tribological properties/lubrication mechanisms and the interactions between the particles and the lubricant co-additives. To answer such questions, state-of-the-art characterization techniques are required, often in situ, and sometimes an extremely complex set up. Some of these can even visualize the behavior of a nanoparticle in real time during a tribological test. The research on this topic has given a good understanding of the way these nanoparticles behave, and we can now identify the key parameters to be adjusted when optimizing their lubrication properties.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2022-0234/

This work aims to investigates exact solutions of the classical Glauert’s laminar wall jet mass and heat transfer under wall suction, wall contraction or dilation, and two thermal transport boundary conditions; prescribed constant surface temperature and prescribed constant surface flux in nanofluidic environment.

The flow system arranged in terms of partial dif- ferential equations is non-dimensionalized with suitable dimensionless transformation variables, and this new set of equations is reduced into ordinary differential equations via a set of similarity transformations, where they are treated analytically for closed form solutions.

Exact solutions of nanofluid flow for velocity distributions, momentum flux, wall shear stress and heat transfer boundary layers for commonly studied nanoparticles; namely copper, alumina, silver, and titanium oxide are presented. The flow behavior of alumina and titanium oxide is identical, and a similar behavior is seen for copper and silver, making two pairs of identical traits. The mathematical expressions as well as visual analysis of wall shear drag and temperature gradient which are of practical interest are analyzed. It is shown that wall stretching or shrinking, wall transpiration and velocity slip together influences the jet flow mechanism and extends the original Glauert’s jet solutions. The exact solutions for the two temperature boundary layer conditions and temperature gradients are analyzed analytically. It is found that the effect of nanopar- ticles concentration on thermal boundary layer is intense, causing temperature uplift, whereas the wall transpiration causes a decrease in thermal layers.

The analysis carried out in nanofluid environment is genuinely new and unique, as our work generalizes the Glauert’s classical regular wall jet fluid problem.