Search results

The purpose of this paper is to describe the first and novel beam splitting day-lighting system possessing highest possible solar transmission efficiency to provide illumination to the core and underground areas of any structure/building.

In this system, by using a number of individually pointable thin and light optical elements mounted on a top of structure/building, the solar light is concentrated. The concentrated beam is focussed to a secondary reflecting element which directs it to a beam splitter while passing through a Fresnel lens and a horizontal solar pipe. The beam splitter located inside the structure/building splits the solar beam into a number of secondary beams using a special arrangement of a number of inbuilt light guiding optical elements inside the beam splitter. The beam splitter produces a desired number of beams which are then redirected to the beam diffusers with the help of the solar pipe and the solar pipe joint which deflects the light at the angle of 90°.

The system considers the use of highly sophisticated and the highly efficient optical elements so that to attain the highest possible end-to-end efficiency of the system. The system has the highest potential to transport the solar energy to larger distances than all the available day-lighting systems and possesses the potential to be used for underground human colonisation.

The widespread adoption of such a system could substantially reduce energy consumption worldwide, which would contribute to bring down the increasing slope in the graph of greenhouse gases.

The paper presents the novel beam splitting day-lighting system.

The utilisation of renewable energy sources for generating electricity and potable water is one of the most sustainable approaches in the current scenario. Therefore, the current research aims to design and develop a novel co-generation system to address the electricity and potable water needs of rural areas.

The cogeneration system mainly consists of a solar parabolic dish concentrator (SPDC) system with a concentrated photo-voltaic module at the receiver for electricity generation. It is further integrated with a low-temperature thermal desalination (LTTD) system for generating potable water. Also, a novel corn cob filtration system is introduced for the pre-treatment to reduce the salt content in seawater before circulating it into the receiver of the SPDC system. The designed novel co-generation system has been numerically and experimentally tested to analyse the performance at Karaikal, U.T. of Puducherry, India.

Because of the pre-treatment with a corn cob, the scale formation in the pipes of the SPDC system is significantly reduced, which enhances the efficiency of the system. It is observed that the conductivity, pH and TDS of seawater are reduced significantly after the pre-treatment by the corncob filtration system. Also, the integrated system is capable of generating 6–8 litres of potable water per day.

The integration of the corncob filtration system reduced the scaling formation compared to the general circulation of water in the hoses. Also, the integrated SPDC and LTTD systems are comparatively economical to generate higher yields of clean water than solar stills.

This paper aims to present the numerical models and experimental outcomes pertain to the performance of the parabolic dish concentrator system with a modified cavity-type receiver (hemispherical-shaped).

The numerical models were evolved based on two types of boundary conditions; isothermal receiver surface and non-isothermal receiver surface. For validation of the numerical models with experimental results, three statistical terms were used: mean of absolute deviation, R² and root mean square error.

The thermal efficiency of the receiver values obtained using the numerical model with a non-isothermal receiver surface found agreeing well with experimental results. The numerical model with non-isothermal surface boundary condition exhibited more accurate results as compared to that with isothermal surface boundary condition. The receiver heat loss analysis based on the experimental outcomes is also carried out to estimate the contributions of various modes of heat transfer. The losses by radiation, convection and conduction contribute about 27.47%, 70.89% and 1.83%, in the total receiver loss, respectively.

An empirical correlation based on experimental data is also presented to anticipate the effect of studied parameters on the receiver collection efficiency. The anticipations may help to adopt the technology for practical use.

The developed models would help to design and anticipating the performance of the dish concentrator system with a modified cavity receiver that may be used for applications e.g. power generation, water heating, air-conditioning, solar cooking, solar drying, energy storage, etc.

The originality of this manuscript comprising presenting a differential-mathematical analysis/modeling of hemispherical shaped modified cavity receiver with non-uniform surface temperature boundary condition. It can estimate the variation of temperature of heat transfer fluid (water) along with the receiver height, by taking into account the receiver cavity losses by means of radiation and convection modes. The model also considers the radiative heat exchange among the internal ring-surface elements of the cavity.

A parabolic trough solar collector is an advanced concentrated solar power technology that significantly captures radiant energy. Solar power will help different sectors reach their energy needs in areas where traditional fuels are in use. This study aims to examine the sensitivity analysis for optimizing the heat transfer and entropy generation in the Jeffrey magnetohydrodynamic hybrid nanofluid flow under the influence of motile gyrotactic microorganisms with solar radiation in the parabolic trough solar collectors. The influences of viscous dissipation and Ohmic heating are also considered in this investigation.

Governing partial differential equations are derived via boundary layer assumptions and nondimensionalized with the help of suitable similarity transformations. The resulting higher-order coupled ordinary differential equations are numerically investigated using the Runga-Kutta fourth-order numerical approach with the shooting technique in the computational MATLAB tool.

The numerical outcomes of influential parameters are presented graphically for velocity, temperature, entropy generation, Bejan number, drag coefficient and Nusselt number. It is observed that escalating the values of melting heat parameter and the Prandl number enhances the Nusselt number, while reverse effect is observed with an enhancement in the magnetic field parameter and bioconvection Lewis number. Increasing the magnetic field and bioconvection diffusion parameter improves the entropy and Bejan number.

Nanotechnology has captured the interest of researchers due to its engrossing performance and wide range of applications in heat transfer and solar energy storage. There are numerous advantages of hybrid nanofluids over traditional heat transfer fluids. In addition, the upswing suspension of the motile gyrotactic microorganisms improves the hybrid nanofluid stability, enhancing the performance of the solar collector. The use of solar energy reduces the industry’s dependency on fossil fuels.

Because of its increased absorptance in fluid and reduced heat loss, direct absorption nanofluid (DANF) is receiving intense interest as an efficient way to harvest solar energy. This work aims to investigate, for the first time, the application of DANF in parabolic trough collectors (PTC), a promising collector for solar thermal systems.

A representative flow and heat transfer study of different fluids in a straight tube is conducted, and the basic energy equation and radiative transfer equations are numerically solved to obtain the fluid temperature distribution and energy conversion efficiency. Ethylene glycol (EG) and different concentrations of (i.e., 0.1-0.6 per cent) multi-wall carbon nanotubes (MWCNT) in EG are used as sample fluids. Four cases are studied for a traditional PTC (i.e., using metal tube) and a direct absorption PTC (i.e., using transparent tube) including a bare tube, a tube with an air-filled glass envelope and a tube with vacuumed glass envelop. The numerical results are verified by an experimental study using a copper-glass absorber tube, which reveals the good potential of DANFs.

Compared with a conventional PTC, using DANF shows an increase of 8.6 per cent and 6.5 K, respectively, in thermal efficiency and outlet temperature difference at a volume fraction (0.5 per cent) of nanoparticles. The results also show that the improvement in solar efficiency increases with increasing particle concentrations, and the vacuum insulated case has the highest efficiency.

In all previous studies, an important section was missing as the effect of photons on the direct solar absorption trough collector, which is considered in this study. This paper proposes a new concept of using direct solar absorption nanofluids for concentrated solar collectors and analyzes the performance of both absorptance and transmittance efficiency considerations. To reveal the potential of the new concept, an analytical model based on energy balance is developed, and two case studies are performed.

Effective cooling is one of the challenges for photovoltaic thermal (PVT) systems to maintain the PV operating temperature. One of the best ways to enhance rate of heat transfer of the PVT system is using advanced working fluids such as nanofluids. The purpose of this research is to develop a numerical model for designing different form of thermal collector systems with different materials. It is concluded that PVT system operated by nanofluid is more effective than water-based PVT system.

In this research, a three-dimensional numerical model of PVT with new baffle-based thermal collector system has been developed and solved using finite element method-based COMSOL Multyphysics software. Water-based different nanofluids (Ag, Cu, Al, etc.), various solid volume fractions up to 3 per cent and variation of inlet temperature (20-40°C) have been applied to obtain high thermal efficiency of this system.

The numerical results show that increasing solid volume fraction increases the thermal performance of PVT system operated by nanofluids, and optimum solid concentration is 2 per cent. The thermal efficiency is enhanced approximately by 7.49, 7.08 and 4.97 per cent for PVT system operated by water/Ag, water/Cu and water/Al nanofluids, respectively, compared to water. The extracted thermal energy from the PVT system decreases by 53.13, 52.69, 42.37 and 38.99 W for water, water/Al, water/Cu and water/Ag nanofluids, respectively, due to each 1°C increase in inlet temperature. The heat transfer rate from heat exchanger to cooling fluid enhances by about 18.43, 27.45 and 31.37 per cent for the PVT system operated by water/Al, water/Cu, water/Ag, respectively, compared to water.

This study is original and is not being considered for publication elsewhere. This is also not currently under review with any other journal.

Volumetric air receivers experience high thermal stress as a consequence of the intense radiation flux they are exposed to when used for heat and/or power generation. This study aims to propose a proper design that is required for the absorber and its holder to ensure efficient heat transfer between the fluid and solid phases and to avoid system failure due to thermal stress.

The design and modeling processes are applied to both the absorber and its holder. A multi-channel explicit geometry design and a discrete model is applied to the absorber to investigate the conjugate heat transfer and thermo-mechanical stress levels present in the steady-state condition. The discrete model is used to calibrate the initial state of the continuum model that is then used to investigate the transient operating states representing cloud-passing events.

The steady-state results constitute promising findings for operating the system at the desired airflow temperature of 700°C. In addition, we identified regions with high temperatures and high-stress values. Furthermore, the transient state model is capable of capturing the heat transfer and fluid dynamics phenomena, allowing the boundaries to be checked under normal operating conditions.

Thermal stress analysis of the absorber and the steady/transient-state thermal analysis of the absorber/holder were conducted. Steady-state heat transfer in the explicit model was used to calibrate the initial steady-state of the continuum model.

This paper aims to present experimental work examining the effect of opening size on the collection efficiency of cavity-type receiver geometries, e.g. modified cavity and spherical cavity with single- as well as dual-stage water heating. The correlations, obtained using the experimentally obtained data, are helpful in designing of cavity receivers (modified and spherical geometry type) to be used in solar-power harnessing assignments/projects, for yielding better system performance.

The parameters of study encompass receiver opening or aperture ratios (d/D, ratio of diameter of opening to the maximum diameter of spherical cavity) of 0.4, 0.47, 0.533 and 0.6; flow Reynolds numbers of 938, 1,175, 1,525 and 1,880 with water as a coolant; and receiver inclination angles of 90, 60, 45 and 30° (with 90° as receiver-opening facing downward and 30° as receiver-aperture facing closer to sideway). A modified cavity receiver was examined for opening ratios of 0.46, 0.6, 0.7 and 0.93. The glass covers, with thickness 2, 4 and 6 mm, were positioned at the opening of cavity to mitigate the energy losses.

The experiments have been conducted at a lesser incoming radiative heat flux, for receiver cavity wall surface temperatures ranging from 90°C to 180°C. The collection efficiency values of both the receivers, modified cavity and spherical cavity types, are seen increasing with coolant flow rate and receiver tilt (inclination) angles, i.e. 30° → 90°. The collection efficiency exhibits maxima at an opening ratio of 0.533 in case of both single- and double-stage spherical cavity receiver. This value was observed as 0.6 for modified cavity receiver. The mathematical correlations developed for obtaining the collection efficiency values of modified cavity-type receiver, spherical cavity receiver with single stage and spherical cavity receiver with dual-stage water heating are given as ɳ=0.4667 Re0.0798dD0.1651 δ0.0281θ̇−0.011, ɳ=0.2317 Re0.124 dD1.265δ0.0192θ̇0.2914 and ɳ=0.1137 Re0.1715dD0.8702θ̇0.2757, respectively.

The findings of the paper may be helpful in erecting concentrating solar collector systems for household water heating, concentrating solar-based power generation as well as for various agricultural applications.

The experimental investigations are fewer in the literature examining the combined geometrical influence on the efficiency of cavity receivers with single- and double-stage water heating provisions.

Solar energy is on a rising trend internationally and in India. The government target of 100 GW solar capacity by 2022 from the present 12 GW is providing a major push for growth in India. However technological development and market competitiveness are pushing down the prices of solar power. The CEO of Amplus Solar has to deal with these challenges to ensure faster growth. He is analysing various options such as expanding the market to include customers who may not be as credit worthy, expanding to foreign geographies, diversification into providing energy efficiency and other services, and entering other markets such as Renewable Energy Certificates, carbon trading, etc.