Search results

The purpose of this paper is to carry out an analytical approximation model (heat transfer model (HTM)) for the calculation of the heat transfer coefficient at the end winding bars of large hydro generators. These coefficients are needed for lumped parameter thermal models in the design process.

The computational fluid dynamics simulation in combination with conjugate heat transfer (CHT) validates the accuracy of the HTM. The theoretical approach describes the formulation of the heat transfer coefficient and the Gauss-Newton method has been applied to find the coefficients of the approximation model.

The paper describes the new analytical approximation model for the heat transfer coefficient at the end winding bars of hydro generators and shows also the validation to simulation results.

The analytical approximation model for the heat transfer coefficient at the end winding bars has been described and a comparison with CHT results has shown a good agreement.

The purpose of this paper is to elucidate the detailed flow field and cavitation effect in the centrifugal pump volute at partial load condition.

Unsteady flows in a centrifugal pump volute at non-cavitation and cavitation conditions are investigated by using a computation fluid dynamics framework combining the re-normalization group k-e turbulence model and the mass transport cavitation model.

The flow field in pump volute is very complicated at part load condition with large pressure gradient and intensive vortex movement. Under cavitation conditions, the dominant frequency for most of the monitoring points in volute transit from the blade passing frequency to a lower frequency. Generally, the maximum amplitudes of pressure fluctuations in volute at serious cavitation condition is twice than that at non-cavitation condition because of the violent disturbances caused by cavitation shedding and explosion.

The detailed flow field and cavitation effect in the centrifugal pump volute at partial load condition are revealed and analysed.

This paper aims to describe the use of optimization approaches to increase the range of near-future howitzer ammunition.

The performance of a gliding projectile concept is assessed using an aeroballistic workflow, comprising aerodynamic characterization and flight trajectory computation. First, a single-objective optimization is run with genetic algorithms to find the maximal attainable range for this type of projectile. Then, a multi-objective formulation of the problem is proposed to consider the compromise between range and time of flight. Finally, the aerodynamic model used for the gliding ammunition is evaluated, in comparison with direct computational fluid dynamics (CFD) computations.

Applying single-objective range maximization results in a great improvement of the reachable distance of the projectile, at the expense of the flight duration. Therefore, a multi-objective optimization is implemented in a second time, to search sets of parameters resulting in an optimal compromise between fire range and flight time. The resulting Pareto front can be directly interpreted and has the advantage of being useful for tactical decisions.

The main limitation of the work concerns the aerodynamic model of the gliding ammunition, which was initially proposed as an alternative to reduce significantly the computational cost of aerodynamic characterization and enable optimizations. When compared with direct CFD computations, this method appears to induce an overestimation of the range. This suggests future evolution to improve the accuracy of this approach.

To the best of the authors’ knowledge, this paper presents an original ammunition concept for howitzers, aiming at extending the range of fire by using lifting surfaces and guidance. In addition, optimization techniques are used to improve the range of such projectile configuration.

The purpose of this paper is to augment heat transfer rates of traditional rib-elements with minimal pressure drop penalties.

The novel geometries in the present research are conventional cylindrical ribs with rounded transitions to the adjacent flat surfaces and with modifications at their bases. All turbulent fluid flow and heat transfer results are presented using computation fluid dynamics with a validated v2f turbulence closure model. Turbulent flow characteristics and heat transfer performances in square channels with improved ribbed structures are numerically analyzed in this research work.

Based on the results, it is found that rounded transition cylindrical ribs have a large advantage over the conventional ribs in both enhancing heat transfer and reducing pressure loss penalty. In addition, cylindrical ribs increase the flow impingement at the upstream of the ribs, which will effectively increase the high heat transfer areas. The design of rounded transition cylindrical ribs and grooves will be an effective way to improve heat transfer enhancement and overall thermal performance of internal channels within blade cooling.

The novel geometries in this research are conventional cylindrical ribs with rounded transitions to the adjacent flat surfaces and with modifications at their bases. The combination of cylindrical ribs and grooves to manipulate the turbulent flow.

The purpose of this paper is to improve the hydraulic efficiency without changing the overall dimension. The blade profile optimization design of the aero-centrifugal pump based on the biharmonic equation surrogate model has been studied.

First of all, Bezier curves and linear function are used to control the annular angle distribution and the stacking angle of blade profile under the MATLAB platform. Grid independence analysis has been studied to find the finest mesh scheme. After the precision comparison of test data and computation fluid dynamics 15 sets of design parameters are carried out as the boundary condition of the biharmonic equation. The efficiency surrogate model of the biharmonic equation is constructed via iteratively solving of a discrete difference equation. The other two surrogate models of response surface model (RSM) and radial basis function neural network surrogate model (RBFNNSM) are compared with the biharmonic equation surrogate model by the standard of modified complex correlation coefficient R² and root mean square deviation (RSME). Finally, the artificial fish swarm algorithm has been used to find the global optimal design parameters with the objective function of highest efficiency.

The results show that the design parameters code conversion method can reduce the number of optimization parameters from five to three, makes the design space become a cube, and compared with RSM and RBFNNSM, the biharmonic equation surrogate model has higher precision with R² is 0.8958, RSME is 0.1382. The final optimum result of AFSA is at the point of [1 −1 −1]. The internal flow field analysis shows that after optimization the outlet relative velocity becomes more uniform and the wake effect has been significantly decreased. The hydraulic efficiency of the optimized pump is about 59.45 per cent increasing 5.4 per cent compared with a prototype pump.

This study developed a new method to optimize the design parameters of aero-centrifugal pump impeller based on biharmonic equation surrogate model, which had a good agreement with experimental values within just 15 sets of the original design. The optimization results shows that the method can improve the hydraulic efficiency significantly.

This paper presents first sight on the longitudinal control strategy for an aircraft in the tandem wing configuration. It is an aerodynamic strongly coupled configuration that needs a lot of detailed aerodynamic analysis which describes the mutual impact of the main parts of the aircraft. The purpose of this paper is to build the numerical model that allows to make an analysis of necessary flaps (front and rear) deflection and prepare the control strategy for this kind of aircraft.

Aircrafts’ aerodynamic characteristics were obtained using the MGAERO software which is a commercial computing fluid dynamics tool created by Analytical Methods, Inc. This software uses the Euler flow model. Results from this software were used in the static stability evaluation and trim condition analysis. The trim conditions are the outcome of the optimisation process whose goal was to find the best front and rear flap deflection to achieve the best lift to drag (L/D) ratio.

The main outcome of this investigation is the proposal of strategy for the front and rear flap deflection which ensured the maximum L/D ratio and satisfied the trim condition. Moreover, the analysis of the mutual impact of the front and rear wings and the analysis of the control surface impact on the aerodynamic characteristic of the aircraft are presented.

In terms of aerodynamic computation, MGAERO software uses an inviscid flow model. However, this research is for the conceptual stage of the design and the MGAERO software grantee satisfied accurate respect to relatively low time of computations.

The ultimate goal is to build an aircraft in a tandem wing configuration and to conduct flying tests or wind tunnel tests. The presented result is one of the milestones to achieve this goal.

The aircraft in the tandem wing configuration is an aerodynamic-coupled configuration that needs detailed analysis to find the mutual interaction between the front and rear wings. Moreover, the mutual impact of the front and rear flaps is necessary too. Obtaining these results allowed this study to build the numerical model of the aircraft in the tandem wing configuration. It allows to find the best strategy of flap deflection, which allows to obtain the maximum L/D ratio and satisfy the trim condition.

The purpose of this paper is to propose a partitioned approach by coupling the smoothed profile method (SPM) and the Euler tension beam model in simulating a vortex-induced vibration of both rigid and flexible cylinders at various reduced velocities.

For the fluid part, SPM in the framework of the spectral element method is adopted to simulate the flow. The advantage of SPM lies in modelling multiple complex shapes as it uses a fixed computational mesh without conformation to the geometry of the particles. For the structure part, an elastic-mounted rigid cylinder is considered in two-dimensional (2D) simulations, while a flexible cylinder with a Euler tension beam model is used in three-dimensional simulations.

Firstly, in the flow past a freely vibrating cylinder, the maximum vibration responses of the cylinder are about 0.73D and 0.1D in the y and x directions, respectively, which occur at the point U_r = 5.75 and are much higher than U_r = 5 in 2D simulations. It is found that the numerical results from the SPM solver are very consistent with those from the NEKTAR-Arbitrary Lagrangian Eulerian method (NEKTAR-ALE) solver or the NEKTAR-Fourier solver. Furthermore, the flow past the tandem cylinders is also investigated, where the upstream cylinder is static while the downstream one is free to vibrate. Specifically, the beating behaviour is captured from the vibration response of the freely vibrating cylinder under the reduced velocity of U_r = 6 with a gap distance of L = 3.5D.

The originality of the paper lies in coupling the SEM with the Euler beam model in simulating the vortex induced vibration (VIV) of flexible cylinders.

Tandem wing aircrafts belong to an unconventional configurations group, and this type of design is characterised by a strong aerodynamic coupling, which results in lower induced drag. The purpose of this paper is to determine whether a certain trend in the wingspan impact on aircraft dynamic stability can be identified. The secondary goal was to compare the response to control of flaps placed on a front and rear wing.

The aerodynamic data and control derivatives were obtained from the computational fluid dynamics computations performed by the MGAERO software. The equations of aircraft longitudinal motion in a state space form were used. The equations were built based on the aerodynamic coefficients, stability and control derivatives. The analysis of the dynamic stability was done in the MATLAB by solving the eigenvalue problem. The response to control was computed by the step response method using MATLAB.

The results of this study showed that because of a strong aerodynamic coupling, a nonlinear relation between the wing size and aircraft dynamic stability proprieties was observed. In the case of the flap deflection, stronger oscillation was observed for the front flap.

Results of dynamic stability of aircraft in the tandem wing configuration can be found in the literature, but those studies show outcomes of a single configuration, while this paper presents a comprehensive investigation into the impact of wingspan on aircraft dynamic stability. The results reveal that because of a strong aerodynamic coupling, the relation between the span factor and dynamic stability is nonlinear. Also, it has been demonstrated that the configuration of two wings with the same span is not the optimal one from the aerodynamic point of view.

To study quantitatively the effects of combined temperature dependent thermodynamics and transport fluid properties on the heat transfer rate, heat function fields and profiles in a fluid filled square enclosure.

Navier‐Stokes equations in two‐dimensions, which are the flow governing equations, were transformed into stream function and vorticity transport equations. These equations together with the energy and heat function equations were cast into their non‐dimensional forms. Numerical solutions of the resulting equations were done by the use of finite‐difference method.

The numerical investigations conducted covered the Rayleigh and Prandtl numbers in the range 10³≤Ra≤10⁶ and 0.01≤Pr≤450, respectively, and expansion parameter ε=(T_h−T_c)/T_R in the range 0.05≤ε≤1. Results show that Boussinesq‐approximation is not sufficient to simulate natural convective flow when the difference between T_h and T_c is high and close to the reference state temperature. The effects of the other fluids properties other than density can be disregarded in computation without significant loss of accuracy. Combined fluid properties have very strong effects on the heat transfer, heat function fields and profiles.

The results of this study will serve as baseline information to designers of heat transfer or process equipment in which fluid at very high temperature occurs.

This paper aims to focus on the effect of the operating condition such as the impeller speed on the centrifugal fan performance and flow characteristics. The ability to predict the behavior of the airflow motion in a centrifugal blower is essential for obtaining the topology optimization design.

A physical model of the air blower consisting of these main parts in a blower system: collector, impeller, outlet flange and volute casing, and the appropriate boundary conditions are set up by ANSYS software. Computation fluid dynamics are performed for the numerical analysis. The calculation of blower performance parameters such as total pressure, efficiency and flow rate is based on the Reynolds averaged Navier–Stokes equations and k-εturbulence flow model.

The numerical results show that the change in operating conditions has a significant effect on the blower performance, and the pressure maintained inside the blower is higher for a larger impeller rotational speed.

This work is original and has not yet been submitted to elsewhere or published previously.