Search results

Fracture properties of concrete are mainly influenced by specimen shape, size and type of testing method. The study aims to identify the characteristic divergence in fracture – evaluating testing methods, i.e. three-point bend test and wedge splitting test for fibrous self-compacting concrete.

A total of nine mixes with three different coarse aggregate sizes (20, 16 and 12.5mm) and three coarse to fine aggregate quantities (40–60, 45–55 and 50–50) were considered to examine the influence of materials on fracture parameters of fibrous self-compacting concrete. For three-point bend test, size effect method was considered to analyze the fracture properties.

The experimental investigation revealed that fracture energy calculated from wedge splitting test was reasonably on higher side for maximum coarse aggregate-based specimens for all coarse to fine aggregate quantities, while for the size effect method, fracture energy value was maximum for least coarse aggregate sized specimens.

The fracture properties of fibrous self-compacting concrete obtained from wedge splitting test method was higher than the size effect method. This is due to the consideration of only peak load for determining the fracture properties in size effect method analysis.

The purpose of this paper is to highlight the sustainability benefits of using demolition and industrial wastes as a replacement for aggregates and cement in traditional concrete mixes.

Crushed concrete from demolition sites served as a replacement for fine and coarse aggregate in some of the mixes at various ratios. In addition, ground granulated blast furnace slag, metakaolin, silica fume, and fly ash each served as a cement replacement for cement content in the mixes tested in this research at various rates. Compression strength tests, permeability, and thermal expansion tests were performed on various mixes to compare their performance to that of traditional mixes with natural aggregate, and with no cement replacement.

The compressive strength results indicated the suitability of using such demolition wastes as replacements in producing green concrete (GC) without hindering its mechanical characteristics significantly. In addition, the results indicated an enhancement in the mechanical characteristics of GC when replacing cement with pozzolanic industrial wastes and byproducts.

The research assesses the utilization of sustainable GC using recycled waste aggregate and byproducts.

This paper aims to investigate the 28-day compressive strength of concrete produced with aggregates from different sources.

Coarse aggregates were crushed granite and natural local stones mined from Umunneochi, Lokpa and Uturu, Isuakwato, respectively, in Abia State, Nigeria. Fine aggregate (river sand) and another coarse aggregate (river stone) were dredged from Otammiri River in Owerri, Imo State, Nigeria. The nominal mix ratios were 1:1:2, 1:2:4 and 1:3:6, whereas the respective water–cement ratios were 0.45, 0.5, 0.55 and 0.6.

The compressive strength of granite concrete, river stone concrete and local stone concrete ranged 17.79-38.13, 15.37-34.57 and 14.17-31.96 N/mm², respectively. Compressive strength was found to increase with decreasing water–cement ratio and increasing cement content.

Granite concrete should be used in reinforced-concrete construction, especially when a cube compressive strength of 30 N/mm² or higher is required.

Granite concrete exceeded the target compressive strength for all the concrete specimens, whereas river stone concrete and local stone concrete failed to achieve the target strength for some mix proportions and water–cement ratios.

This study aims to present the results of an experimental evaluation of low (M30), mid (M40) and high (M50) grade self-compacting concrete (SCC) with three nominal maximum aggregate sizes (NMAS), namely, 20 mm, 16 mm and 12.5 mm, with Bailey gradation (BG) in comparison with Indian standard gradation (ISG).

This study was conducted in a laboratory by testing the characteristics of fresh and hardened properties of self-compacting concrete.

Rheological and mechanical properties of SCC were evaluated in detail and according to the results, a concrete sample containing lower NMAS with BG demonstrated improvement in modulus of elasticity and compressive strength, while improving the rheological properties as well. Meanwhile, SCC demonstrated poor performance in split tensile and flexural strengths with lower NMAS gradations and a direct correlation was evident as the increase in NMAS caused an increase in the strength and vice-versa.

Upon comparison of BG with ISG, it was revealed that BG mixes succeeded to demonstrate superior performance. From the material optimization, rheological and mechanical performance study, it is recommended that BG with NMAS 16 mm can be used for conventional SCC.

This paper aims to qualify traditional concrete mixtures for large-scale material extrusion in an automated, additive manufacturing process or additive construction.

A robust and viable automated additive construction process must be developed that has the capability to construct full-scale, habitable structures using materials that are readily available near the location of the construction site. Accordingly, the applicability of conventional concrete mixtures for large-scale material extrusion in an additive construction process was investigated. A qualitative test was proposed in which concrete mixtures were forced through a modified clay extruder and evaluated on performance and potential to be suitable for nozzle extrusion typical of additive construction, or 3D printing with concrete. The concrete mixtures were further subjected to the standard drop table test for flow, and the results for the two tests were compared. Finally, the concrete mixtures were tested for setting time, compressive strength and flexural strength as final indicators for usefulness in large-scale construction.

Conventional concrete mixtures, typically with a high percentage of coarse aggregate, were found to be unsuitable for additive construction application due to clogging in the extruder. However, reducing the amount of coarse aggregate provided concrete mixtures that were promising for additive construction while still using materials that are generally available worldwide.

Much of the work performed in additive manufacturing processes on a construction scale using concrete focuses on unconventional concrete mixtures using synthetic aggregates or no coarse aggregate at all. This paper shows that a concrete mixture using conventional materials can be suitable for material extrusion in additive construction. The use of conventional materials will reduce costs and allow for additive construction to be used worldwide.

This study aims to investigate the compressive strength of concretes incorporating Linz-Donawitz slag (LD slag) as partial replacement for natural fine and coarse aggregates and compare them with traditional concrete.

The natural fine and coarse aggregates were replaced by weight simultaneously up to 100% with LD slag aggregates at an incremental increase of 20%. Concrete of grades M20, M25, M30, M35 and M40 were cast, cured and tested with standard cube specimens to study the density and compressive strength of reference and LD slag aggregate concretes (LDSACs). The concrete specimens were exposed to elevated temperatures, i.e. 100 to 900 °C at an equal interval of 100 °C and tested to study the variation in density and residual compressive strength.

The results from the experiments reveal that the LDSAC yields a higher density than that of the reference concrete and also undergo less density variation when exposed to elevated temperatures. In addition, the residual compressive strength of LDSAC specimens was significantly higher than that of the reference concrete.

LD slag is believed to be stronger and more durable than locally available limestone aggregates or blast furnace slag. Moreover, it is necessary to study its strength and other properties to determine whether it can be successfully used as an aggregate in concrete universally.

Use of LD slag as aggregates in concrete will convert LD slag into a value added product and as an alternative to the existing natural aggregates which will help in maintaining ecological balance and save valuable lands.

The economically weaker section of the society may now use LDSAC as waste utilization will bring down the overall cost and hence it will benefit people on large scale.

Use of LD slag as aggregate in concrete can help find an alternative to the existing natural aggregates which will save the ecosystem and at the same time help in reducing the industrial waste on a large scale.

Utilising industrial waste, such as fly ash (FA) and bagasse ash (BA), reduces waste management and increases mechanical strength. Concrete is modified with FA and BA in the cool bonded method of concrete preparation.

The study used to partially replace cement with BA powder at proportions 0, 5, 10, 15, 20 and 25% and coarse aggregates are replaced with FA aggregates made with FA and cement using a cold-bonded technique at proportions 0–25%. FA aggregates were made at 10:90, 15:85, 20:80 and 25:75 proportions of cement and FA. The FA aggregates at the best proportion 15:85 was selected as a coarse aggregate by conducting tests like specific gravity, crushing value, impact value and water absorption tests.

The addition of 30% content decreases porosity by 21% and increases strength significantly at 28 days. Microstructure evolution is carried out to identify material behaviour.

Mechanical and durable properties such as flexural strength, tensile strength, water absorption test, acid and alkaline tests are conducted on M50 grade concrete after 3–28 days of curing.

The purpose of this paper is to investigate the potential use of construction and demolition waste materials (C&DWM) as an alternative for natural fine aggregates (NFA), in view to solve the disposal problems caused due to landfills. In addition, to evaluate its suitability as a sustainable material, mechanical and durability properties have been performed on different proportions of concrete blending and the results recorded were compared with the reference concrete values.

In this research, the NFA were replaced at the proportion of 25%, 50%, 75% and 100% of C&DWM with a constant slump range of 130 mm–150 mm. This parameter will assess the consistency of the fresh concrete during transportation process. The characteristics of the end product was evaluated through various tests conducted on hardened concrete samples, namely, compressive strength, flexural strength, depth of penetration of water under pressure, rapid chloride penetration test, carbonation test and ultrasonic pulse velocity (UPV) test. All results recorded were compared with the reference concrete values.

The results demonstrated that the use of C&DWM in concrete portrayed prospective characteristics that could eventually change the concept of sustainable concrete. It was noted that the compressive and flexural strength decreased with the addition of C&DWM, but nevertheless, a continuous increase in strength was observed with an increase in curing period. Moreover, the increase in rapid chloride penetration and decrease in UPV over time period suggested that the concrete structure has improved in terms of compactness, thus giving rise to a less permeable concrete. The mechanical tests showed little discrepancies in the final results when compared to reference concrete. Therefore, it is opined that C&DWM can be used effectively in concrete.

This study explores the possible utilisation of C&DWM as a suitable surrogative materials in concrete in a practical perspective, where the slump parameter will be kept constant throughout the experimental process. Moreover, research on this method is very limited and is yet to be elaborated in-depth. This approach will encourage the use of C&DWM in the construction sector and in the same time minimise the disposal problems caused due to in landfills.

The quest to reduce the cost of concrete which is a major construction input has prompted investigations into assessing the suitability of alternative sources of conventional materials. This paper aims to report the compressive strength and workability of lateritic gravel used as all-in aggregate for concrete production.

Three prescribed mixes from all-in aggregate concrete were compared with concrete from lateritic gravel. The paper investigated the variation in strength of four different mixes – 100: 0, 90: 10, 80: 20 and 70: 30 – when portions of the lateritic gravel were replaced with pit sand, respectively, using varying water cement ratios to achieve optimal workability.

The density and compressive strength of each cube was measured on the 7th and 28th test dates. An increase in slump and compressive strength was observed in the lateritic concrete, as portions of the lateritic gravel were replaced with sand. However, the rate of increase in the compressive strength tended to decrease with increase in part replacement of lateritic gravel with sand indicating that there was a threshold of percentage of sand increase after which the compressive strengths are likely to decrease. This work never reached this threshold, but it is estimated to be about 40 per cent.

Investigations focused on lateritic gravel sampled from two sites to represent samples from both the forest and savannah belt.

Lateritic gravel can be used as all-in aggregate for non-structural concrete.

The compressive strengths achieved were better than those for the available normal all-in aggregate used.

This paper presents the effects of replacing fine aggregate (FA) with waste foundry sand (WFS) in natural aggregate and construction waste aggregate concrete specimens without and with superplasticizer (SP), silica fume (SF) and fiber (F) to solve the disposal problems of various wastes along with saving the environment. This study aims to investigate the effect of construction waste, WFS along with additives on the stress-strain behavior and development of compressive strength with age.

The various concrete specimen were prepared in mix proportion of 1: 2: 4 (cement (C): sand: coarse aggregate). The water-cement ratio of 0.5 (decreased by 10% for samples containing SP) to grading 1: 2: 4 under air-dry condition was adopted in the preparation of concrete specimens. The compressive strength of various concrete specimen were noticed for 3, 7 and 28 days by applying load through universal testing machine.

Upon adding construction and demolition waste aggregates, the compressive strength of concrete after 28 days was comparable to that of the control concrete specimen. An enhancement in the value of compressive strength is perceived when FA is replaced with WFS to the extent of 10%, 20% and 30%. If both construction and demolition waste aggregate and WFS replacing FA are used, the compressive strength increases. When FA is interchanged with WFS in natural aggregate or construction demolition waste aggregate concrete including usage of SF or F, the compressive strength improves significantly. Further, when construction and demolition waste aggregate and WFS replacing FA including SP are used, the compressive strength improves marginally compared to that of control specimen. The rate of strength development with age is observed to follow similar trend as in control concrete specimen. Therefore, construction and demolition waste and or WFS can be used effectively in concrete confirming an improvement in strength.

The utilization of these wastes in concrete will resolve the problem of their disposal and save the environment.