Search results

Differential pressure is an important technological parameter, one urgent task of which is control and measurement. To date, the lion’s share of research in this area has focused on the development and improvement of differential pressure sensors. The purpose of this paper is to develop a smart differential pressure sensor with improved operational and metrological characteristics.

The operating principle of the developed pressure sensor is based on the capacitive measurement principle. The measuring unit of the developed pressure sensor is based on a differential capacitive sensitive element. Programmable system-on-chip (PSoC) technology has been used to develop the electronics unit.

The use of a differential capacitive sensitive element allows the unit to compensate for the influence of interference (for example, temperature) on the measurement result. With the use of PSoC technology, it is also possible to increase the noise immunity of the developed smart differential pressure sensor and provide an unparalleled combination of flexibility and integration of analog and digital functionality.

The use of PSoC technology in the developed smart differential pressure sensor has many indisputable advantages, as the size of the entire circuit can be minimized. As a result, the circuit has improved noise immunity. Accordingly, the procedure for debugging and changing the software of the electronics unit is simplified. These features make development and manufacturing cost effective.

In this work, the sensing and actuating elements are designed with interdigitated capacitors away from the sensitive element on which the droplet is placed. This pattern helps to prevent interference of electrical elements with the droplet. Choosing shear resonance mode at this proposed structure minimizes the damping effect of droplet touch by the resonator structure. The glass-based standard fabrication method of the proposed biosensor is presented exactly.

Mechanical resonator sensors are extremely limited because of the high damping factor and the high electrical conductivity in the aqueous environment. In this work, a molecule detector biosensor is proposed for droplet analysis, which is possible to fabricate using micro-electro-mechanical systems (MEMS) technology. By electromechanical coupling of resonators as a mechanical resonator structure, a standing mechanical wave is formed at this structure by electrostatic actuating elements.

In this paper, a mechanical resonator structure as a biosensor is proposed for micro-droplet analysis that can be fabricated by MEMS technology. It is designed at a lower cost fabrication method using electrostatic technology and interdigitated capacitors. The response of the biosensor displacement frequency at the resonance frequency of the desired mode is reasonable for measuring the capacitive changes of its output. The mass sensitivity of the proposed biosensor is in the range of 1 ng, and it has a large sensitive area for capturing target molecules.

To evaluate the quality of the proposed design, the stimulated analysis is conducted by COMSOL and results are presented.

The purpose of this paper is to develop a program based on three‐dimensional finite element analysis to model different patterns of capacitive proximity sensors. This program can be used as a development tool to optimize the structure and size of a sensor for a desired or for a given sensitivity and linearity range and as a consequence to save sensor design time. A set of experiments have been conducted to test the tool capabilities for designing different sensor structures.

Finite element analysis in ANSYS software was used to perform electrostatic field simulations and to calculate the capacitance between electrodes of a capacitive proximity sensor when a conducting target is placed in some distance from the sensor plate.

Several capacitive proximity sensor structures have been designed, analyzed and tested to illustrate the accuracy of the simulated results obtained from the design tool. After design and implementation of a sensor and comparing the extracted and measured capacitance values, it is shown that the finite element analysis is an accurate method to extract fringing capacitance in capacitive proximity sensors in comparison to the analytical tool based on the finite difference method.

This automatic capacitive proximity sensor design tool can optimize a sensor structure with specific shape and size to have more sensitivity or linearity according to the application in use. Moreover, the modeling program can extract characteristics of a sensor with user‐defined parameters.

The purpose of this paper is to analyse the possibilities of mechanical switch replacement by capacitive film touch sensor in applications requiring high reliability and short response time. Advantage of replacing mechanical switch by capacitive touch sensor is no mechanical wear and possible implementation of sensor in application where the switch could not be used or where the flexibility of the sensor substrate is required. The aim of this work is to develop a capacitive touch sensor with the advantage of maximum mechanical resistance, short response time and high sensitivity.

Based on various possible sensors layouts, the authors realized 18 different (14 self-capacitance and four mutual capacitance) topologies of capacitive sensor for touch applications. Three different technologies – PCB, LTCC and polymer technology – were used to characterize sensor’s behaviour. For precise characterization of different layouts realized on various substrates, the authors used integrated circuit FDC2214 capacitance-to-digital converter.

Sensing range of the capacitive touch (proximity) sensor is affected by the per cent of area covered by the sensor, and it does not depend on topology of sensor. The highest sensing range offers PCB technology. Flexible substrates can be used as proper substituent to rigid PCB.

The novelty of this work lies in finding the touch capacitive sensors that allow shorter switching times compared to standard mechanical switches.

With the development of artificial intelligence, proximity sensors show their great potential in intelligent perception. This paper aims to propose a new planar capacitive sensor for the proximity sensing of a conductor.

Different from traditional structures, the proposed sensor is characterized by sawtooth-structured electrodes. A series of numerical simulations have been carried out to study the impact of different geometrical parameters such as the width of the main trunk, the width of the sawtooth and the number of sawtooths. In addition, the impact of the lateral offset of the approaching graphite block is investigated.

It is found that sensitivity is improved with the increase of the main trunk with, sawtooth width and sawtooth number while a larger lateral offset leads to a decrease in sensitivity. The performance of the proposed planar capacitive proximity sensor is also compared with two conventional planar capacitive sensors. The results show that the proposed planar capacitive sensor is obviously more sensitive than the two conventional planar capacitive sensors.

In this paper, a new planar capacitive sensor is proposed for the proximity sensing of a conductor. The results show that the capacitive sensor with the novel structure is obviously more sensitive than the traditional structures in the detection of the proximity conductor.

The purpose of this paper is to consider a capacitive pressure sensor fabricated using low‐temperature cofired ceramic (LTCC) materials and technology as a candidate for an energy‐autonomous sensor application. Designing the 3D capacitive sensor structure, with the cofired thick‐film electrodes inside the narrow air gap in the LTCC substrate, was a challenging task, particularly due to the presence of the parasitic elements influencing the sensor's characteristics.

In this work, different design variants for the thick‐film electrodes of the capacitive sensing structure were studied and compared. The test sensors were designed for the pressure range 0‐10 kPa and manufactured with readout electronics based on a capacitance‐to‐digital conversion.

The typical sensitivity obtained was 4 fF/kPa, and the temperature coefficient of the sensitivity was 0.03%/°C. The design variant with the guard‐ring electrode showed the best rms resolution of 50 Pa. One drawback of the application could be the sensitivity to atmospheric humidity and the influence of the different media.

This paper focuses on the design of a capacitive gas‐pressure sensor in a 3D LTCC structure. The present study provides a good basis for further optimisation of the design of the cofired electrodes in the capacitive sensing structure.

The purpose of this study is to develop a cylindrical capacitive sensor that has the advantages of high resolution, small size and designability and can be easily installed on lubricant pipeline to monitor lubricant oil debris.

A theoretical model of the cylindrical capacitive sensor is presented to analyze several parameters’ effectiveness on the performance of sensor. Numerical simulations are then conducted to determine the optimal parameters for preliminary experiments. Experiments are finally carried out to demonstrate the detectability of developed capacitive sensors.

It is clear from experimental results that the developed capacitive sensor can monitor the debris in lubricant oil well, and the capacitance values increase almost linearly when the number and size of debris increase.

There is lot of further work to do to apply the presented method into the application. Especially, it is necessary to consider several factors’ influence on monitoring results. These factors include the flow rate of the lubricant oil, the temperature, the debris distribution and the vibration. Moreover, future work should consider the influence of the oil degradation to the capacitance change and other contaminations (e.g. water and dust).

This work conducts a feasibility study on application of capacitive sensing principle for detecting debris in aero engine lubricant oil.

The novelty of the presented capacitance sensor can be summarized into two aspects. One is that the sensor structure is simple and characterized by two coaxial cylinders as electrodes, while conventional capacitive sensors are composed of two parallel plates as electrodes. The other is that sensing mechanism and physical model of the presented sensor is verified and validated by the simulation and experiment.

The aim of this review is to present together the studies on textile-based moisture sensors developed using innovative technologies in recent years.

The integration levels of the sensors studied with the textile materials are changing. Some research teams have used a combination of printing and textile technologies to produce sensors, while a group of researchers have used traditional technologies such as weaving and embroidery. Others have taken advantage of new technologies such as electro-spinning, polymerization and other techniques. In this way, they tried to combine the good working efficiency of the sensors and the flexibility of the textile. All these approaches are presented in this article.

The presentation of the latest technologies used to develop textile sensors together will give researchers an idea about new studies that can be done on highly sensitive and efficient textile-based moisture sensor systems.

In this paper humidity sensors have been explained in terms of measuring principle as capacitive and resistive. Then, studies conducted in the last 20 years on the textile-based humidity sensors have been presented in detail. This is a comprehensive review study that presents the latest developments together in this area for researchers.

While the transference of charge is an essential aspect of every capacitance sensor, a relatively new form of sensor makes overt use of the principle of charge conservation first deduced by Watson in the 1740s. Updated to use a microcontroller, mosfet switches, fet‐input opamps and band gap references, the principle of charge transference can be used to create an extremely sensitive and stable device with unique properties that transcend those of more pedestrian capacitance sensors. Also known as “QT” sensors, charge transfer sensors can have a dynamic range spanning many decades with noise floors in the sub‐femtofarad regime, allowing differential resolutions of mere fractions of a femtofarad. Such sensors are proving to have unique applications considered heretofore impossible, while also proving themselves as replacements for much more expensive sensing systems using photoelectric, acoustic, RF, and optical imaging techniques.

The purpose of this paper is the development and study of capacitive coupling electrodes with the ability to monitor the quality of the skin–electrode contact in the process of electrocardiogram (ECG) diagnostics. The study’s scope embraces experimental identification of distortions contributed into the recorded ECG signal at various degrees of disturbance of the skin–electrode contact.

A capacitive coupling electrode is designed and manufactured. A large number of experiments was carried out to record ECG signals with different quality of the skin–electrode contact. Using spectral analysis, the characteristic distortions of the ECG signals in the event of contact disturbance are revealed.

It was found that the violation of the skin–electrode contact leads to significant deterioration in the recorded signal. In this case, the most severe distortions appear with various violations of the skin–electrode contact of two sensors in one lead. It has been experimentally shown that the developed sensor allows monitoring the quality of the contact, and therefore, improvement of the quality of signal registration, enabled by the use of bespoke processing algorithms.

These sensors will be used in personalized medicine devices and tele-ECG devices.

In this work, authors studied the effect of the skin–electrode contact of a capacitive electrode with the body on the quality of the recorded ECG signal. Based on the studies, the necessity of monitoring contact was shown to improve the quality of diagnostics provided by personalized medicine devices; the capacitive sensor with contact feedback was developed.