Search results

The purpose of this paper is to investigate use of calabrian pine (pinus brutia) cone (CPC) dust along with borax (BX) to assess the effect of friction coefficient. Despite the number of research studies completed on the mechanism of friction in automotive brake lining materials, the phenomenon is still not fully understood. Complex mechano-chemical processes occurring on the friction interface of a composite friction material make it difficult to understand the correlation between the formulation of brake lining and the frictional performance.

In this study, the use of CPC dust along with BX has been investigated for assessing the effect on friction coefficient. CPC has resin in it. BX is a boron production which is widely used in boron glass production and in ceramic industry for increasing the heat- resistant and -forming abrasion resistant. Newly formulated brake lining material with five different ingredients has been tested under Friction Assessment and Screening Test. Friction coefficient, wear rate and scanning electron microscope for friction surface were examined to assess the performance of these samples.

Analysis of the experimental results shows that the brake lining material containing CPC and BX significantly improved the stability of the friction coefficient, fade and wear resistance.

Several investigations have been conducted to use different materials in brake pads. The brake pad standards have been provided in previous studies, as well as the aims for economical and sustainable production. In the present study, production of brake pads by CPC dust and BX has been executed. Parallel results have been presented between previously reported and present study, in view of brake characteristics and wear resistance. Use of the lower cost and productive organic sources of material are the main improvement of the present study.

The purpose of this study is to establish an effective method for characterizing the tribological properties of friction brakes during continuous braking because they have direct influences on the reliable operation of transport vehicles and industrial equipments.

First, tribological tests were carried out with the X-DM type friction tester, and changing curves of friction coefficient and temperature were obtained. Second, a novel tribological characteristic parameter set characterizing the tribological properties of brake pair in continuous braking was extracted from some important experimental data such as friction coefficient, wear rate and temperature. Finally, the influence of law and mechanism of braking number on dynamic tribological parameters was studied through continuous braking experiments.

The extracted tribological characteristic parameter set includes two subsets: dynamic characteristic parameter subset and overall characteristic parameter subset, which is composed of ten parameters: dynamic parameters of friction coefficient (including average, trend coefficient and stability coefficient), dynamic wear rate, dynamic average temperature, dynamic temperature rise, overall average friction coefficient, overall wear rate, overall average temperature and overall temperature rise.

Conclusively, the novel tribological characteristic parameter set is more comprehensive and objective, and it can provide a theoretical basis for the study of tribological properties in continuous braking.

The purpose of this paper is to investigate the effect of fly ash content on the friction–wear performance of bronze-based brake lining material.

In this study, bronze-based brake linings containing 0-12 weight per cent fly ash were produced by the hot-pressing process. The friction-wear properties of the unreinforced bronze matrix brake lining material and fly ash reinforced samples were investigated using a Chase-type friction tester. The hardness and density of the samples were also determined. The microstructures and friction surfaces of the samples were examined using scanning electron microscopy.

The experimental results showed that the fly ash content significantly affects the friction-wear properties of the brake lining material. It was found that the friction coefficient increases with the increase in the fly ash content for the brake lining materials studied. Moreover, the mass losses in the wear test were lower for the brake linings containing over 4 weight per cent fly ash than unreinforced bronze-based lining material.

This study has proven to be useful in exploring fly ash particles as low cost reinforcing materials in improving the friction–wear performance of bronze-based brake lining material. In addition, the use of fly ash particles in the manufacture of brake lining materials contributes to reducing the production cost of brake linings and to a sustainable environment.

The purpose of this study is to investigate the influence of commercially available iron–aluminum alloy compared to copper, iron and aluminum powders on the tribological performances of friction composites. The main objective is to replace copper from the friction composite formulations.

In this study, friction composites were fabricated as of standard brake pads using commercially available iron–aluminum alloy and compared to copper powder, iron powder and aluminum powder-based without varying the other ingredients. The brake pads were developed as per the industrial procedure. The physical, mechanical and thermal properties of the developed brake pads were analyzed as per industrial standards. Tribological properties were analyzed using the chase test. Initial speed and deceleration tests in a real-time braking scenario were performed using a full-scale inertia brake dynamometer. Worn surface analysis was done using a scanning electron microscope.

The results indicate that iron–aluminum alloy (mechanomade)-based friction composites possess good physical, chemical, thermal and mechanical properties with stable fade and recovery characteristics due to its composition and flake morphology. During initial speed and deceleration braking conditions, iron–aluminum alloy also showed good tribological behavior.

This paper explains the influence of commercially available iron–aluminum alloy in friction composites in enhancing tribological performance by its composition and flake morphology, which could potentially replace copper in friction composites by solving subsequent problems.

The purpose of this paper is to investigate use of colemanite (C) upon friction and wear performance of automotive brake lining. Brake lining production with the boron product colemanite addition and braking characterization investigated for development of non-asbestos organic (NAO) brake lining because of negative effects on human health and environmental hazard of asbestos containing linings. During the braking, brake lining is warmed up extremely due to friction, and the high temperature causes to decreasing of breaking performance. Colemanite has high melting temperature, and this makes this material valuable for brake lining.

This study investigated the effect of colemanite (C) upon friction and wear performance of automotive brake lining. Based on a simple experimental formulation, different amounts of boron product colemanite were used and then evaluated using a friction assessment and screening test. In these specimens, half of the samples (shown with H indices) were heat treated in 4 h at 180°C temperature. Friction coefficient, wear rate and scanning electron microscope for friction surfaces were used to assess the performance of these samples.

The results of test showed that colemanite can substantially improve properties of friction materials. The friction coefficient of friction materials modified with colemanite varies steadily with the change of temperature, and the wearing rate of friction materials is relatively low by using colemanite. Heat treatment-applied samples (CH) have provided a higher and stable friction coefficient. These results indicate that colemanite has ideal application effect in various friction materials.

This paper fulfils an identified information and offers practical help to the industrial firms working with brake lining and also to the academicians working on wear of materials. Parallel results have been presented between previously reported and present study, in view of brake characteristics and wear resistance. Use of the lower cost and productive organic sources of material are the main improvement of the present study.

This study aims to explore the impact of key parameters of brake pads on the dynamic characteristics of the braking system.

This study conducted experimental research based on a friction testing machine with a slider-disc structure. The experiment studied the impact of key parameters of brake pads (rotation speed, pressure, mass, braking radius, etc.) and the braking environment (dry friction, wetness, sand, etc.) on the stability of the braking system. At the same time, a dynamic model of the brake pad braking system was established and compared with experimental results using the mathematical tool of autocorrelation coefficient.

The key parameters of brake pads have a significant impact on the dynamic characteristics of the braking system; under different conditions of brake pad mass, tribological parameters, brake pad radius and braking environment, the chaotic characteristics of the braking friction force signal show a trend of expansion or contraction, which can be suppressed by adjusting the key parameters of brake pads.

This study can provide a reference for optimizing the braking strategy and reducing noise and vibration in brake pad systems.

This study aims to clarify the relationship of friction material type and brake disc temperature through braking experiment.

The braking performances of resin materials (RM), semimetallic materials (SM) and copper-based powder metallurgy materials (PM) friction blocks mating with forged steel brake disc were examined based on TM-I-type reduced-scale inertial braking dynamometer. The brake disc surface temperature was recorded by infrared thermal camera during braking.

Experimental results indicate that the thermal wear resistance of three friction materials differs with mental content, resulting in the deviation of pad-disc system contact state during braking, thus forming different temperature distribution on the brake disc surface. The peak temperature on the disc face of RM (190°C) is 36.6% and 45.4% lower than that of PM (300°C) and SM (348°C) at 160 km/h. The maximum radial temperature deviation of PM (35°C) is approximately three times than that of RM (12°C) and 40% higher than that of SM (25°C) at 50 km/h, whereas the maximum temperature deviation of SM (97°C) is six times than that of RM (16°C) and 31% higher than that of PM (74°C) at 160 km/h.

The effect of friction material type on the disc surface temperature distribution is revealed, which provides a meaningful reference for the design of brake friction pairs and choice of brake pad materials.

This study aims to determine the braking performance of limestone as a filler in brake friction materials.

Samples containing limestone material (30-35-40%), which can be an alternative to brake friction material filler, were produced. The samples were weighed on precision scales, mixed homogeneously and produced using the hot molding method. The physical and tribological properties of the produced samples were determined, and their microscopic analyzes were made with scanning electron microscopy.

As the amount of limestone increased, the density of the samples decreased. The friction coefficient and wear rates were close to each other and within the optimum limits for all samples. Limestone materials can be used instead of barite materials studied in the literature on brake linings. Microcracks were observed only in samples containing 30% and 35% limestone in microscopic images.

In this study, the wear rate, coefficient of friction and microstructures on the friction surfaces of brake friction materials containing limestone were investigated. The usability of limestone as a filler in brake friction materials provides valuable information to researchers and industrial organizations in the brake friction material field.

This study aims to discuss the impact of using bio-polymer (kraft lignin) in the formulation of passenger vehicle disc brake pads (as a substitute for cashew nutshell liquid [CNSL]-based friction dust) and investigate the characteristics of the pads.

Within the scope of this investigation, three different brake pads were generated by altering the biopolymer-lignin content in conjunction with the friction dust from CNSL without modifying the other components. The brake pads were created in accordance with industry-standard practices. Industrial standards were used to evaluate the newly created brake pad’s thermal, physical and mechanical qualities. The tribological properties of the materials were determined using a full-scale inertia brake dynamometer. The scanning electron microscope examined the worn surfaces in conjunction with elemental mapping.

The test findings suggest that the brake pads filled with biopolymer-lignin and CNSL-based friction dust (as a partial replacement 50%) exhibited excellent thermal, physical, mechanical characteristics, as well as steady friction and low wear rate.

A bio-polymer (kraft lignin) in friction composites has the potential to produce eco-friendly brake pads and improve the tribological performance of its copper free-composition, which might be used to replace CNSL-based friction dust in friction composites by addressing the issues raised in this work.

The purpose of this paper, brake friction material samples with six different contents were produced using three different fiber types consisting of variable proportions of huntite mineral and basalt, glass and steel fibers. The friction properties and formation of the transfer film in these friction materials were investigated.

Friction materials were produced using a hot molding method from materials containing 10%–15% huntite in varying proportions, consisting of basalt, glass and steel fibers. The densities and hardness values of the samples were measured. Friction tests were performed using a brake pad friction material tester to determine tribological properties. After the friction tests, microscopic examination of the sample surfaces was performed using scanning electron microscope (SEM) and three-dimensional (3D) surface profilometer devices.

Huntite mineral content and fiber type affected the friction coefficient. With an increase in the amount of huntite, the friction coefficient increased in the friction material samples formed with glass and steel fibers. The fiber type and amount of huntite also affected the transfer film formation. The surface roughness values of all the friction materials decreased with an increase in the amount of huntite. The surface roughness values of the samples with glass fibers were higher than those of other samples.

The importance of using huntite minerals and different fiber types in automotive brake friction materials is emphasized. This will help industrial companies and academics study the tribological properties of friction materials.