Search results

1 – 10 of over 1000
Article
Publication date: 13 September 2023

Bifu Xiong, Siliang He, Jinguo Ge, Quantong Li, Chuan Hu, Haidong Yan and Yu-An Shen

This paper aims to examine the effects of bonding temperature, bonding time, bonding pressure and the presence of a Pt catalyst on the bonding strength of Cu/SB/P-Cu/SB/Cu joints…

Abstract

Purpose

This paper aims to examine the effects of bonding temperature, bonding time, bonding pressure and the presence of a Pt catalyst on the bonding strength of Cu/SB/P-Cu/SB/Cu joints by transient liquid phase bonding (TLPB).

Design/methodology/approach

TLPB is promising to assemble die-attaching packaging for power devices. In this study, porous Cu (P-Cu) foil with a distinctive porous structure and Sn-58Bi solder (SB) serve as the bonding materials for TLPB under a formic acid atmosphere (FA). The high surface area of P-Cu enables efficient diffusion of the liquid phase of SB, stimulating the wetting, spreading and formation of intermetallic compounds (IMCs).

Findings

The higher bonding temperature decreased strength due to the coarsening of IMCs. The longer bonding time reduced the bonding strength owing to the coarsened Bi and thickened IMC. Applying optimal bonding pressure improved bonding strength, whereas excessive pressure caused damage. The presence of a Pt catalyst enhanced bonding efficiency and strength by facilitating reduction–oxidation reactions and oxide film removal.

Originality/value

Overall, this study demonstrates the feasibility of low-temperature TLPB for Cu/SB/P-Cu/SB/Cu joints and provides insights into optimizing bonding strength for the interconnecting materials in the applications of power devices.

Details

Soldering & Surface Mount Technology, vol. 36 no. 1
Type: Research Article
ISSN: 0954-0911

Keywords

Article
Publication date: 18 January 2024

Uğur Kemiklioğlu, Sermet Demir and Caner Yüksel

Adhesively bonded joints are used in many fields, especially in the automotive, marine, aviation, defense and outdoor industries. Adhesive bonding offers advantages over…

Abstract

Purpose

Adhesively bonded joints are used in many fields, especially in the automotive, marine, aviation, defense and outdoor industries. Adhesive bonding offers advantages over traditional mechanical methods, including the ability to join diverse materials, even load distribution and efficient thermal-electrical insulation. This study aims to investigate the mechanical properties of adhesively bonded joints, focusing on adherends produced with auxetic and flat surfaces adhered with varying adhesive thicknesses.

Design/methodology/approach

The research uses three-dimensional (3D)-printed materials, polyethylene terephthalate glycol and polylactic acid, and two adhesive types with ductile and brittle properties for single lap joints, analyzing their mechanical performance through tensile testing. The adhesion region of one of these adherends was formed with a flat surface and the other with an auxetic surface. Adhesively bonded joints were produced with 0.2, 0.3 and 0.4 mm bonding thickness.

Findings

Results reveal that auxetic adherends exhibit higher strength compared to flat surfaces. Interestingly, the strength of ductile adhesives in auxetic bonded joints increases with adhesive thickness, while brittle adhesive strength decreases with thicker auxetic bonds. Moreover, the auxetic structure displays reduced elongation under comparable force.

Originality/value

The findings emphasize the intricate interplay between adhesive type, bonded surface configuration of adherend and bonding thickness, crucial for understanding the mechanical behavior of adhesively bonded joints in the context of 3D-printed materials.

Details

Rapid Prototyping Journal, vol. 30 no. 3
Type: Research Article
ISSN: 1355-2546

Keywords

Article
Publication date: 18 March 2024

Lifeng Wang, Fei Yu, Ziwang Xiao and Qi Wang

When the reinforced concrete beams are reinforced by bonding steel plates to the bottom, excessive use of steel plates will make the reinforced concrete beams become…

Abstract

Purpose

When the reinforced concrete beams are reinforced by bonding steel plates to the bottom, excessive use of steel plates will make the reinforced concrete beams become super-reinforced beams, and there are security risks in the actual use of super-reinforced beams. In order to avoid the occurrence of this situation, the purpose of this paper is to study the calculation method of the maximum number of bonded steel plates to reinforce reinforced concrete beams.

Design/methodology/approach

First of all, when establishing the limit failure state of the reinforced member, this paper comprehensively considers the role of the tensile steel bar and steel plate and takes the load effect before reinforcement as the negative contribution of the maximum number of bonded steel plates that can be used for reinforcement. Through the definition of the equivalent tensile strength, equivalent elastic modulus and equivalent yield strain of the tensile steel bar and steel plate, a method to determine the relative limit compression zone height of the reinforced member is obtained. Second, based on the maximum ratio of (reinforcement + steel plate), the relative limit compression zone height and the equivalent tensile strength of the tensile steel bar and steel plate of the reinforced member, the calculation method of the maximum number of bonded steel plates is derived. Then, the static load test of the test beam is carried out and the corresponding numerical model is established, and the reliability of the numerical model is verified by comparison. Finally, the accuracy of the calculation method of the maximum number of bonded steel plates is proved by the numerical model.

Findings

The numerical simulation results show that when the steel plate width is 800 mm and the thickness is 1–4 mm, the reinforced concrete beam has a delayed yield platform when it reaches the limit state, and the failure mode conforms to the basic stress characteristics of the balanced-reinforced beam. When the steel plate thickness is 5–8 mm, the sudden failure occurs without obvious warning when the reinforced concrete beam reaches the limit state. The failure mode conforms to the basic mechanical characteristics of the super-reinforced beam failure, and the bending moment of the beam failure depends only on the compressive strength of the concrete. The results of the calculation and analysis show that the maximum number of bonded steel plates for reinforced concrete beams in this experiment is 3,487 mm2. When the width of the steel plate is 800 mm, the maximum thickness of the steel plate can be 4.36 mm. That is, when the thickness of the steel plate, the reinforced concrete beam is still the balanced-reinforced beam. When the thickness of the steel plate, the reinforced concrete beam will become a super-reinforced beam after reinforcement. The calculation results are in good agreement with the numerical simulation results, which proves the accuracy of the calculation method.

Originality/value

This paper presents a method for calculating the maximum number of steel plates attached to the bottom of reinforced concrete beams. First, based on the experimental research, the failure mode of reinforced concrete beams with different number of steel plates is simulated by the numerical model, and then the result of the calculation method is compared with the result of the numerical simulation to ensure the accuracy of the calculation method of the maximum number of bonded steel plates. And the study does not require a large number of experimental samples, which has a certain economy. The research result can be used to control the number of steel plates in similar reinforcement designs.

Details

International Journal of Structural Integrity, vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 1757-9864

Keywords

Open Access
Article
Publication date: 27 January 2023

Damira Dairabayeva, Asma Perveen and Didier Talamona

Currently on additive manufacturing, extensive research is directed toward mitigating the main challenges associated with multi-material in fused filament fabrication which has a…

Abstract

Purpose

Currently on additive manufacturing, extensive research is directed toward mitigating the main challenges associated with multi-material in fused filament fabrication which has a weak bonding strength between dissimilar materials. Low interfacial bonding strength leads to defects, anisotropy and temperature gradient in materials which negatively impact the mechanical performance of the multi-material prints. The purpose of this study was to assess the performance of different interface geometry designs in terms of the mechanical properties of the specimens.

Design/methodology/approach

Tensile test specimens were printed using: mono-material without a boundary interface, mono-material with the interface geometries (Face-to-face; U-shape; T-shape; Dovetail; Encapsulation; Mechanical interlocking; and Overlap) and multi-material with the interface geometries. The materials chosen with high and low compatibility were Tough polylactic acid (PLA) and TPU.

Findings

The main results of this study indicate that the interface geometries with the mechanical constriction between materials provide better structural integrity to the specimens. Moreover, in the case of the mono-material parts, the most effective interface design was the mechanical interlocking for both Tough PLA and TPU. On the other hand, in the case of multi-material specimens, the encapsulation showed the highest ultimate tensile strength, whereas the overlap and T-shape presented more robust bonding.

Originality/value

This study examines the mechanical performance, particularly tensile strength, strain at break, Young’s modulus and yield strength of different interface designs which were not studied in the previous studies.

Details

Rapid Prototyping Journal, vol. 29 no. 11
Type: Research Article
ISSN: 1355-2546

Keywords

Article
Publication date: 3 November 2023

Shubham Bansal, Lokesh Choudhary, Megha Kalra, Niragi Dave and Anil Kumar Sharma

One of the most contested and anticipated research issues is the acceptability of using recycled aggregates instead of fresh aggregates. This study aims to look at the possibility…

Abstract

Purpose

One of the most contested and anticipated research issues is the acceptability of using recycled aggregates instead of fresh aggregates. This study aims to look at the possibility of replacing fresh aggregates with 15%, 30%, 60% and 100% recycled aggregates.

Design/methodology/approach

The research is divided into two stages. The compressive, split tensile, flexural and bond strength of the various mixes were examined in the first phase using untreated recycled concrete aggregates (RCA). The second phase entails chemically treating RCA with a 10% 0.1 M sodium metasilicate solution to evaluate differences in strength, indicating the success of the treatment performed. Microstructural experiments such as scanning electron microscopy and X-ray diffraction were also conducted to evaluate the formation of interfacial transition zone (ITZ) in treated and untreated RCA specimens.

Findings

The observed findings reveal a decrease in concrete strength with increasing RCA concentration; however, when treated RCA was used, the strengths increased significantly when compared to untreated samples. The findings also include curves indicating the correlation between compressive strength and other mechanical strength parameters for an optimum mix of concrete prepared with 30% RCA replacement.

Originality/value

The study through its novel approach, demonstrates the effect of pretreatment of RCA in the absence of any standardized chemical treatment methodology and presents significant potential in minimizing reliance on fresh aggregates used in concrete, lowering building costs and promoting the use of waste materials in construction.

Details

Journal of Engineering, Design and Technology , vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 1726-0531

Keywords

Article
Publication date: 27 June 2023

Ao Zhang, Jian Zhang, Mingjun Zhang, Junyi Liu and Ping Peng

This paper aims to investigate the effect and mechanism of O atom single doping, Ce and O atoms co-doping on the interfacial microscopic behavior of brazed Ni-Cr/diamond.

Abstract

Purpose

This paper aims to investigate the effect and mechanism of O atom single doping, Ce and O atoms co-doping on the interfacial microscopic behavior of brazed Ni-Cr/diamond.

Design/methodology/approach

Using first-principles calculations, the embedding energy, work of separation, interfacial energy and electronic structures of Ni-Cr-O/diamond and Ni-Cr-O-Ce/diamond interface models were calculated. Then, the effect of Ce and O co-doping was experimentally verified through brazed diamond with CeO2-added Ni-Cr filler alloy.

Findings

The results show that O single-doping reduces the interfacial bonding strength between Ni-Cr filler alloy and diamond but enhances its interfacial stability to some extent. However, the Ce and O co-doping simultaneously enhances the interfacial bonding strength and stability between Ni-Cr filler alloy and diamond. The in-situ formed Ce-O oxide at interface impedes the direct contact between diamond and Ni-Cr filler alloy, which weakens the catalytic effect of Ni element on diamond graphitization. It is experimentally found that the fine rod-shaped Cr3C2 and Cr7C3 carbides are generated on diamond surface brazed with CeO2-added Ni-Cr filler alloy. After grinding, the brazed diamond grits, brazed with CeO2-added Ni-Cr filler alloy, present few fracture and the percentage of intact diamond reaches 67.8%. Compared to pure Ni-Cr filler alloy, the brazed diamond with CeO2-added Ni-Cr filler alloy exhibit the better wear resistance and the slighter thermal damage.

Originality/value

Using first-principles calculations, the effect of Ce and O atoms co-doping on the brazed diamond with Ni-Cr filler alloy is investigated, and the calculation results are verified experimentally. Through the first-principles calculations, the interface behavior and reaction mechanism between diamond and filler alloy can be well disclosed, and the composition of filler alloy can be optimized, which will be beneficial for synergistically realizing the enhanced interface bonding and reduced thermal damage of brazed diamond.

Details

Soldering & Surface Mount Technology, vol. 35 no. 5
Type: Research Article
ISSN: 0954-0911

Keywords

Article
Publication date: 21 August 2023

Erwin Molino Alvarez, Sergio Andres Quintana González, Luis Lisandro Lopez Taborda and Enrique Esteban Niebles Nuñez

Additive manufacturing has disadvantages, such as the maximum part size being limited by the machine’s working volume. Therefore, if a part more considerable than the working…

Abstract

Purpose

Additive manufacturing has disadvantages, such as the maximum part size being limited by the machine’s working volume. Therefore, if a part more considerable than the working volume is required, the part is produced in parts and joined together. Among the many methods of joining thermoplastic parts, adhesives and mechanical interlocking are considered. This study aims to characterize and optimize mechanically stressed adhesive joints combined with female and male mechanical interlocking on acrylonitrile butadiene styrene (ABS) specimens made with fused filament fabrication (FFF) so that the joint strength is as close as possible to the strength of the base material.

Design/methodology/approach

This study characterized the subject’s state of the art to justify the decisions regarding the experimental design planned in this research. Subsequently, this study designed, executed and analyzed the experiment using a statistical analysis of variance. The output variables were yield strength and tensile strength. The input variables were two different cyanoacrylate adhesives, two different types of mechanical interlock (truncated pyramid and cylindrical pin) and the dimensions of each type of mechanical interlock. This study used simple and factorial experiments to select the best adhesive and interlocking to be optimized using the response surface and the steep ascent method.

Findings

The two adhesives have no statistical difference, but they show different data dispersion. The design or yield stress was a determining factor for selecting the optimal specimen, with cylindrical geometry exhibiting higher resistance at initial failure. Geometry type is crucial due to the presence of stress concentrators. The cylindrical geometry with fewer stress concentrators demonstrated better tensile strength. Ultimately, the specimen with a mechanically reinforced joint featuring a cylindrical pin of radius 5.45 mm and height of 4.6 mm exhibited the maximum tensile and yield strength.

Originality/value

Previous research suggests that a research opportunity is the combination of bonding methods in FFF or fused deposition modeling, which is not a frequent topic, and this research to enrich that topic combines the adhesive with mechanically interlocked joints and studies it experimentally for FFF materials, to provide unpublished information of the performance of the adhesive joint with mechanical interlocking, to designers and manufacturers of this technology.

Article
Publication date: 27 September 2023

Vivek Kumar Tiwary, Arunkumar Padmakumar and Vinayak R. Malik

Material extrusion (MEX) 3D printers suffer from an intrinsic limitation of small size of the prints due to its restricted bed dimension. On the other hand, friction stir spot…

Abstract

Purpose

Material extrusion (MEX) 3D printers suffer from an intrinsic limitation of small size of the prints due to its restricted bed dimension. On the other hand, friction stir spot welding (FSSW) is gaining wide interest from automobile, airplane, off-road equipment manufacturers and even consumer electronics. This paper aims to explore the possibility of FSSW on Acrylonitrile Butadiene Styrene/Polylactic acid 3D-printed components to overcome the bed size limitation of MEX 3D printers.

Design/methodology/approach

Four different tool geometries (tapered cylindrical pin with/without concavity, pinless with/without concavity) were used to produce the joints. Three critical process parameters related to FSSW (tool rotational speed, plunge depth and dwell time) and two related to 3D printing (material combination and infill percentages) were investigated and optimized using the Taguchi L27 design of experiments. The influence of each welding parameter on the shear strength was evaluated by analysis of variance.

Findings

Results revealed that the infill percentage, a 3D printing parameter, had the maximum effect on the joint strength. The joints displayed pull nugget, cross nugget and substrate failure morphologies. The outcome resulted in the joint efficiency reaching up to 100.3%, better than that obtained by other competitive processes for 3D-printed thermoplastics. The results, when applied to weld a UAV wing, showed good strength and integrity. Further, grafting the joints with nylon micro-particles was also investigated, resulting in a detrimental effect on the strength.

Originality/value

To the best of the authors’ knowledge, this is the first study to demonstrate that the welding of dissimilar 3D-printed thermoplastics with/without microparticles is possible by FSSW, whilst the process parameters have a considerable consequence on the bond strength.

Details

Rapid Prototyping Journal, vol. 30 no. 1
Type: Research Article
ISSN: 1355-2546

Keywords

Article
Publication date: 29 December 2023

Sepehr Ghazinoory and Parvaneh Aghaei

This study aims to investigate the importance and effect of asymmetric technological collaborations’ key success factors in developing countries. The number of collaborations…

Abstract

Purpose

This study aims to investigate the importance and effect of asymmetric technological collaborations’ key success factors in developing countries. The number of collaborations between large enterprises and SMEs, known as asymmetric technological collaborations (ATC) is growing considerably. But this asymmetry in itself can increase the number and intensity of collaboration challenges. So far, limited studies have been conducted on the stability of ATCs, and most of them have been in the context of developed countries. Meanwhile, studying the strength and stability of collaboration in the nano industry with growing market value and increasing newcomers is of particular importance.

Design/methodology/approach

Here, with bionic engineering approach, we used chemistry for the first time to identify the main stability factors of ATCs and build our hypotheses and research model. To this end, we introduced the factors affecting the stability of the dative chemical bond as a bionic counterpart of corporate venture capital (CVC), which is a type of ATC, and proposed 4 hypotheses. We used structural equation modeling (SEM) with partial least squares (PLS) method to examine the hypothesized relationships.

Findings

The analysis of survey questionnaire data from 26 asymmetric collaborations in Iran’s nanotechnology industry shows that “learning of the acceptor company” with a negative effect, “network ties” and “development of the collaboration host region” with a positive effect and “diversity in the collaboration portfolio” with an inverted U-shaped effect are the most influential factors in the stability and continuity of CVCs, respectively.

Originality/value

The findings of this research can be the beginning of a broad path leading to exploring and getting inspiration from chemistry to analyze management issues.

Details

Journal of Business & Industrial Marketing, vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 0885-8624

Keywords

Article
Publication date: 30 January 2024

Burçak Zehir, Mirsadegh Seyedzavvar and Cem Boğa

This study aims to comprehensively investigate the mixed-mode fracture behavior and mechanical properties of selective laser sintering (SLS) polyamide 12 (PA12) components…

Abstract

Purpose

This study aims to comprehensively investigate the mixed-mode fracture behavior and mechanical properties of selective laser sintering (SLS) polyamide 12 (PA12) components, considering different build orientations and layer thicknesses. The primary objectives include the following. Conducting mixed-mode fracture and mechanical analyses on SLS PA12 parts. Investigating the influence of build orientation and layer thickness on the mechanical properties of SLS-printed components. Examining the fracture mechanisms of SLS-produced Arcan fracture and tensile specimens through experimental methods and finite element analyses.

Design/methodology/approach

The research used a combination of experimental techniques and numerical analyses. Tensile and Arcan fracture specimens were fabricated using the SLS process with varying build orientations (X, X–Y, Z) and layer thicknesses (0.1 mm, 0.2 mm). Mechanical properties, including tensile strength, modulus of elasticity and critical stress intensity factor, were quantified through experimental testing. Mixed-mode fracture tests were conducted using a specialized fixture, and finite element analyses using the J-integral method were performed to calculate fracture toughness. Scanning electron microscopy (SEM) was used for detailed morphological analysis of fractured surfaces.

Findings

The investigation revealed that the highest tensile properties were achieved in samples fabricated horizontally in the X orientation with a layer thickness of 0.1 mm. Additionally, parts manufactured with a layer thickness of 0.2 mm exhibited favorable mixed-mode fracture behavior. The results emphasize the significance of build orientation and layer thickness in influencing mechanical properties and fracture behavior. SEM analysis provided valuable insights into the failure mechanisms of SLS-produced PA12 components.

Originality/value

This study contributes to the field of additive manufacturing by providing a comprehensive analysis of the mixed-mode fracture behavior and mechanical properties of SLS-produced PA12 components. The investigation offers novel insights into the influence of build orientation and layer thickness on the performance of such components. The combination of experimental testing, numerical analyses and SEM morphological observations enhances the understanding of fracture behavior in additive manufacturing processes. The findings contribute to optimizing the design and manufacturing of high-quality PA12 components using SLS technology.

Details

Rapid Prototyping Journal, vol. 30 no. 3
Type: Research Article
ISSN: 1355-2546

Keywords

1 – 10 of over 1000