Search results

The purpose of this paper is to conduct research on the possibility of improving the tribological and utilization properties of lard and rapeseed oil bio-based greases by mixing it with ethanol and selection of thickener and modification with special biological additives.

Rapeseed oil- and lard-based greases with sodium and lithium soap thickeners were mixed with either water or ethanol and modified with a special biological anti-wear additive. Tribological properties of modified lubricants evaluated on a four-ball machine.

Rapeseed oil- and lard-based greases suspended in ethanol and modified with bio-additive have the same wear resistance as the industrial non-biological lubrication grease and much higher wear resistance as bio-based reference grease. The tribological efficiency of the additives is higher in greases of rapeseed oil and less efficient in lard-based greases. Oxidation and wear tests show that investigated bio-based greases have comparatively stable tribological properties also after their aging. Modified greases have sufficient consistence according penetration measurements and high thermal resistance according drop-point temperature measurements. All produced experimental greases pass within the category of the easily degradable materials.

The greases mixed with the ethanol make possible to form more homogeneous and stable grease mixture. Modified bio-based greases have significantly higher wear resistance as bio-based reference grease, their lubrication properties are stable also after the aging and are categorized as easily degradable materials.

The purpose of this paper is to report on the tribological properties of beef tallow grease and improvements therein through modification with special processing, polymeric compounds and additives.

Pure original beef tallow grease was used as a biological lubricating grease reference material for the tribological research. Beef tallow was modified and synthesized by adding special biological anti-oxidant additives, LZ anti-wear additives, waste polyethylene terephthalate (PET) polymer compounds and thermally processed graphite.

Rheometric measurements indicate that the beef tallow grease modification technology used in this study enables control of the synthesis process to produce lubricants with the required microstructure. Investigation results of the tribological properties of differently modified greases show that beef tallow synthesized with polymer additives efficiently operates together with anti-wear additives to reduce friction and wear. The grease compound with thermally processed graphite has good tribological properties at 300 N load levels. The critical load level of lubricating greases could be significantly increased through the use of anti-wear additives and thermally processed graphite.

Investigation results of the tribological properties of differently modified beef tallow greases show that beef tallow synthesized with polymer additives efficiently operates together with anti-wear additives to reduce friction and wear. The critical load level of lubricating beef tallow greases could be significantly increased using anti-wear additives and thermally processed graphite.

The aim of this paper was to investigate the possibility of reusing frying oil, obtained during thermal treatment of food in fast-food restaurants for production of plastic greases.

In accordance with the proposed research concept, the used frying oil was to be the base oil of biodegradable plastic greases thickened with calcium 12-hydroxystearate and lithium 12-hydroxystearate. These studies included the determination of the effect of variable amounts of used oil component in the base oil on the properties of the resultant plastic greases.

It was found that the optimum amount of the component in the base oil is 10-15 per cent. Calcium and lithium greases prepared in such a way possess a quality to that of greases prepared with fresh rapeseed oil.

Higher concentrations of used frying oil in the base oil adversely affect the degree of thickening, thixotropic properties and dropping point of the grease, as well as, creating technological problems.

The investigations, beside their research goals have also a practical character – recycling waste material in place of its present method of disposal.

One of the least expensive material, and most commonly used to produce biodegradable lubricants are vegetable oils. In recent years, besides introducing biodegradable lubricating oils, increasing interest is observed in the use of plastic greases of high biodegradability. Now, it is possible to obtain such greases with additive of used frying oils. Biodegradable greases are used as lubrication of open gear, food production equipment, central lubrication system in cars and railway engineering.

Describes the requirements for biodegradability, defines the different terms and lists the various tests used. Outlines how greases can cause pollution. Details the main primary biodegradability test for lubricants and how to formulate greases to optimize breakdown in the environment and still lubricate well. Gives examples of commercial biodegradable greases.

The new authorities created by this Act, probably the most important local government measure of the century, will be voted into existence during 1973 and commence functioning on 1st April 1974. Their responsibilities and the problems facing them are in many ways quite different and of greater complexity than those with which existing councils have had to cope. In its passage through the Lords, a number of amendments were made to the Act, but in the main, it is a scheme of reorganization originally produced after years of discussion and long sessions in the Commons. Local government reorganization in Scotland takes place one year later and for Northern Ireland, we must continue to wait and pray for a return of sanity.

Following in the footsteps of pharmacy and food processing the textile industry makes recourse to enzymes on an increasing scale. Biotechnology makes the textile processes more ecological. In the 1990's, attempts were made in Poland to lessen the undesirable effect of carbonization by using enzymes to remove vegetable impurities from wool. Pre-treatment of wool with an enzyme bath in the carbonizing process helped reduce the concentration of sulphuric acid from 6% to 1.5%. The developed technology of cleaning wool from vegetable impurities is conventionally described as the 'BIOCARBO of Wool'.

This paper presents the results of laboratory and technological trails of using enzymatic treatments for remove vegetable impurities from wool. Enzymes, which are complex proteins, are specifically active only in relation to certain substances. This is an advantage as far as grease wool is concerned, since wool and its vegetable impurities have different chemical structures. In addition, the properties of uncleaned wool and of wool cleaned by the biological method are discussed.

Pre‐treatment of wastewater discharged from a potato‐chips factory was the subject of this study. Wastewater discharged from this factory is characterized by high values of BOD, TSS and oil and grease (3,685, 4,115 and 169mg/l, respectively). Treatability studies via continuous aerobic and anaerobic methods treatment have been investigated. The results obtained showed marked improvement in the quality of the treated effluent using packing material versus the upflow anaerobic sludge bed reactor (UASB) without packing. An extra removal in COD (53 per cent), BOD (61 percent), TSS (52 per cent) and oil and grease (46 per cent) was obtained. Corresponding residual values were 398mgO₂/l, 235mgO₂/l, 108mg/l and 38mg/l, respectively. Based on the laboratory results, engineering designs and economic evaluation of the different treatment systems were developed.

Artificial intelligence (AI) models are demonstrating day by day that they can find long-term solutions to improve wastewater treatment efficiency. Artificial neural networks (ANNs) are one of the most important of these models, and they are increasingly being used to forecast water resource variables. The goal of this study was to create an ANN model to estimate the removal efficiency of biological oxygen demand (BOD), total nitrogen (TN), total phosphorus (TP) and total suspended solids (TSS) at the effluent of various primary and secondary treatment methods in a wastewater treatment plant (WWTP).

The MATLAB App Designer model was used to generate the data set. Various combinations of wastewater quality data, such as temperature(T), TN, TP and hydraulic retention time (HRT) are used as inputs into the ANN to assess the degree of effect of each of these variables on BOD, TN, TP and TSS removal efficiency. Two of the models reflect two different types of primary treatment, while the other nine models represent different types of subsequent treatment. The ANN model’s findings are compared to the MATLAB App Designer model. For evaluating model performance, mean square error (MSE) and coefficient of determination statistics (R2) are utilized as comparative metrics.

For both training and testing, the R values for the ANN models were greater than 0.99. Based on the comparisons, it was discovered that the ANN model can be used to estimate the removal efficiency of BOD, TN, TP and TSS in WWTP and that the ANN model produces very similar and satisfying results to the APPDESIGNER model. The R-value (Correlation coefficient) of 0.9909 and the MSE of 5.962 indicate that the model is accurate. Because of the many benefits of the ANN models used in this study, it has a lot of potential as a general modeling tool for a range of other complicated process systems that are difficult to solve using conventional modeling techniques.

The objective of this study was to develop an ANN model that could be used to estimate the removal efficiency of pollutants such as BOD, TN, TP and TSS at the effluent of various primary and secondary treatment methods in a WWTP. In the future, the ANN could be used to design a new WWTP and forecast the removal efficiency of pollutants.

The main purpose of this study is to provide technical support for industrial firms in a new Egyptian industrial city in order to comply with the National Regulatory Standards for wastewater discharge into the public sewerage network.

An execution plan has been prepared to identify the existing environmental status of all the enterprises in the city. To accomplish the planned activities, relevant information was collected from the available records in the city. A unified questionnaire format has been designed for all enterprises including all activities and information required for this study. Accordingly, industries were classified according to their activities and sizes. The information was fed to the computer using a database to control data entry, analysis, and retrieval. Also, the work plan included industrial auditing, wastewater characterization, and application of pollution prevention measures and treatment of end‐of‐pipe.

Statistical analysis of the collected data showed that 119 enterprises were distributed among different industrial sectors. The size of factories according to number of employees is categorized as micro, small and medium. Characterization of industrial wastewater produced from 37 plants indicated that 50 percent thereof do not comply with the Egyptian environmental laws, for industrial wastewater discharge into the public sewage network. In this study, three factories were selected to solve their environmental problems. Treatability studies and/or pollution prevention approaches for the selected factories were carried out and the recommended solutions were implemented and proved to be cost‐effective.

This paper provides the guidelines for other factories in this Egyptian industrial city to be environmentally friendly via compliance with the local regulatory standards. Dissemination of the achieved results can be applied by other industrial cities in Egypt.

The Hamilton canal in the western province of Sri Lanka is a man-made canal situated in an area with immense anthropogenic pressures. The purpose of this study is to identify the quality variations of the water in Hamilton canal and human perception about the present status of the water of the canal.

Sampling has been carried out in seven locations in the canal during dry and wet periods for water quality analysis. In situ field-testing and laboratory analysis have been conducted for physicochemical, heavy metal, oil and grease analysis of water. Only Pb, Cd, oil and grease were tested in the canal sediments. The samples were analyzed as per the standard methods of the American Public Health Association (APHA) Manual: 20th edition. A semi-structured questionnaire survey has been carried out to assess the human perception on the water of the canal.

The results revealed that average EC, Turbidity, Total Hardness, TDS, F⁻, Fe²+, Cl⁻, SO₄²⁻ and PO₄³⁻ of the canal water remained above the threshold limits of inland water standards. Concentrations of Pb and Cd were also above the standards in some locations. Oil and grease were in a very high level in water and sediments.

The water of the canal has been affected by nutrient, heavy metal and oil and grease pollution at present. Discharge of domestic, industrial, municipal wastes and sewage are the prominent reasons which have encouraged the deterioration of the quality of water in the canal.