Search results

The purpose of this paper is to investigate the feasibility of using micro electromechanical systems (MEMS) to convert a binary phase shift keying (BPSK) signal to a simpler amplitude shift keying (ASK) scheme.

The prototype is designed within the SOIMUMPs® fabrication process constraints. The fabrication constraints imposed geometric limitations on what could be tested. These constraints were used to build a mathematical model, which in turn was used to optimize the response using MATLAB®. The optimized design was tested using finite element analysis with CoventorWare®, and finally lab tests on the fabricated device were performed to confirm theoretical predictions.

Theoretical predictions compared well with lab measurements on a prototype device measuring 2.9 mm². The prototype was tested with a carrier frequency of 174 kHz at a BPSK data rate of 3 kHz and carrier amplitude of 6 V. With these parameters, ASK modulation indices of 0.96 and 0.94 were measured at the two output sensors.

This study provides a MEMS solution for BPSK to ASK conversion. The study also identifies what limits betterment of the modulation index and data rate. Such a device has potential application in wireless sensor network (WSN) nodes that have energy harvesters and sensors that are also built in MEMS. Being a MEMS device, it can facilitate integration in such WSN nodes and, hence, potentially reduce size and costs.

The purpose of this paper is to propose a new optical steganography framework that can be applied to public optical binary phase-shift keying (BPSK) systems by transmitting a stealth spectrum-amplitude-coded optical code-division multiple-access signal through a BPSK link.

By using high-dispersion elements, the stealth data pulses temporally stretch and the amplitude of the signal decreases after stretching. Thus, the signal can be hidden underneath the public signal and system noise. At the receiver end, a polarizer is used for removing the public BPSK signal and the stealth signal is successfully recovered by a balanced detector.

In a simulation, the bit-error rate (BER) performance improved when the stealth power increased.

The BER performance worsens when the noise power become large. Future work will consider increasing the system performance during high-noise power situation.

By properly adjusting the power of the amplified spontaneous emission noise, the stealth signal can be hidden well in the public channel while producing minimal influence on the public BPSK signal.

In conclusion, the proposed optical steganography framework makes it more difficult for eavesdroppers to detect and intercept the hidden stealth channel under public transmission, even when using a dispersion compensation scheme.

The purpose of this paper is to design and construct an amplitude shift keying (ASK) modulator, which, using the digital binary modulating signal, controls a floating memristor emulator (MR) internally without the need for additional control circuits to achieve the ASK modulated wave.

A binary digital unipolar signal to be modulated is converted by a pre-processor circuit into a suitable bipolar modulating direct current (DC) signal for the control of the MR state, using current conveyors the carrier signal’s amplitude is varied with the change in the memristance of the floating MR. A high pass filter is then used to remove the DC control signal (modulating signal) leaving only the modulated carrier signal.

The results from the experiment and simulation are in agreement showed that the MR can be switched between two states and that a change in the carrier signals amplitude can be achieved by using an MR. Thus, showing that the circuit behavior is in line with the proposed theory and validating the said theory.

In this paper, the binary signal to be modulated is modified into a suitable control signal for the MR, thus the MR relies on the internal operation of the modulator circuit for the control of its memristance. An ASK modulation can then be achieved using a floating memristor without the need for additional circuits or signals to control its memristance.

A recent innovative technology used in wireless communication is recognized as multiple input multiple output (MIMO) communication system and became popular for quicker data transmission speed. This technology is being examined and implemented for the latest broadband wireless connectivity networks. Though high-capacity wireless channel is identified, there is still requirement of better techniques to get increased data transmission speed with acceptable reliability. There are two types of systems comprising of multi-antennas placed at transmitting and receiving sides, of which first is diversity technique and another is spatial multiplexing method. By making use of these diversity techniques, the reliability of transmitting signal can be improved. The fundamental method of the diversity is to transform wireless channel such as Rayleigh fading into steady additive white Gaussian noise (AWGN) channel which is devoid of any disastrous fading of the signal. The maximum transmission speed that can be achieved by spatial multiplexing methods is nearly equal to channel capacity of MIMO. Conversely, for diversity methods, the maximum speed of broadcasting is much lower than channel capacity of MIMO. With the advent of space–time block coding (STBC) antenna diversity technique, higher-speed data transmission is achievable for spatially multiplexed multiple input multiple output (SM-MIMO) system. At the receiving end, detection of the signal is a complex task for system which exhibits SM-MIMO. Additionally, a link modification method is implemented to decide appropriate coding and modulation scheme such as space diversity technique STBC to use two-way radio resources efficiently. The proposed work attempts to improve detection of signal at receiving end by employing STBC diversity technique for linear detection methods such as zero forcing (ZF), minimum mean square error (MMSE), ordered successive interference cancellation (OSIC) and maximum likelihood detection (MLD). The performance of MLD has been found to be better than other detection techniques.

Alamouti's STBC uses two transmit antennas regardless of the number of receiver antennas. The encoding and decoding operation of STBC is shown in the earlier cited diagram. In the following matrix, the rows of each coding scheme represent a different time instant, while the columns represent the transmitted symbols through each different antenna. In this case, the first and second rows represent the transmission at the first and second time instant, respectively. At a time t, the symbol s₁ and symbol s₂ are transmitted from antenna 1 and antenna 2, respectively. Assuming that each symbol has duration T, then at time t + T, the symbols –s₂* and s₁*, where (.)* denotes the complex conjugate, are transmitted from antenna 1 and antenna 2, respectively. Case of one receiver antenna: The reception and decoding of the signal depend on the number of receiver antennas available. For the case of one receiver antenna, the received signals are received at antenna 1 , hij is the channel transfer function from the jth transmit antenna and the ith receiver antenna, n1 is a complex random variable representing noise at antenna 1 and x (k) denotes x at time instant k ( at time t + (k – 1)T.

The results obtained for maximal ratio combining (MRC) with 1 × 4 scheme show that the BER curve drops to 10–4 for signal-to-noise (SNR) ratio of 10 dB, whereas for MRC 1 × 2 scheme, the BER drops down to 10–5 for SNR of 20 dB. Results obtained in Table 1 show that when STBC is employed for MRC with 1 × 2 scheme (one antenna at transmitter node and two antennas at receiver node), BER curve comes down to 0.0076 for Eb/N0 of 12. Similarly, when MRC with 1 × 4 antenna scheme is implemented, BER drops down to 0 for Eb/N0 of 12. Thus, it can be concluded from the obtained graph that the performance of MRC with STBC gives improved results. When STBC technique is used with 3 × 4 scheme, at SNR of 10 dB, BER comes nearer to 10–6 (figure 7.3). It can be concluded from the analytics observed between AWGN and Rayleigh fading channel that for AWGN channel, BER is found to be equal to 0 for SNR value of 13.5 dB, whereas for Rayleigh fading channel, BER is observed nearer to 10–3 for Eb/N0 = 15. Simulation results (in figure 7.2) from the analytics show BER drops to 0 for SNR value of 12 dB.

Optimal design and successful deployment of high-performance wireless networks present a number of technical challenges. These include regulatory limits on useable radio-frequency spectrum and a complex time-varying propagation environment affected by fading and multipath. The effect of multipath fading in wireless systems can be reduced by using antenna diversity. Previous studies show the performance of transmit diversity with narrowband signals using linear equalization, decision feedback equalization, maximum likelihood sequence estimation (MLSE) and spread spectrum signals using a RAKE receiver. The available IC techniques compatible with STBC schemes at transmission require multiple antennas at the receiver. However, if this not a strong constraint at the base station level, it remains a challenge at the handset level due to cost and size limitation. For this reason, SAIC technique, alternative to complex ML multiuser demodulation technique, is still of interest for 4G wireless networks using the MIMO technology and STBC in particular. In a system with characteristics similar to the North American Digital mobile radio standard IS-54 (24.3 K symbols per sec. with an 81 Hz fading rate), adaptive retransmission with time deviation is not practical.

The evaluation of performance in terms of bit error rate and convergence time which estimates that MLD technique outperforms in terms of received SNR and low decoding complexity. MLD technique performs well but when higher number of antennas are used, it requires more computational time and thereby resulting in increased hardware complexity. When MRC scheme is implemented for singe input single output (SISO) system, BER drops down to 10–2 for SNR of 20 dB. Therefore, when MIMO systems are employed for MRC scheme, improved results based on BER versus SNR are obtained and are used for detecting the signal; comparative study based on different techniques is done. Initially ZF detection method is utilized which was then modified to ZF with successive interference cancellation (ZFSIC). When successive interference cancellation scheme is employed for ZFSIC, better performance is observed as compared to the estimation of ML and MMSE. For 2 × 2 scheme with QPSK modulation method, ZFSIC requires more computational time as compared to ZF, MMSE and ML technique. From the obtained results, the conclusion is that ZFSIC gives the improved results as compared to ZF in terms of BER ratio. ZF-based decision statistics can be produced by the detection algorithm for a desired sub-stream from the received vector whichs consist of an interference which occurred from previous transmitted sub-streams. Consequently, a decision on the secondary stream is made and contribution of the noise is regenerated and subtracted from the vector received. With no involvement of interference cancellation, system performance gets reduced but computational cost is saved. While using cancellation, as H is deflated, coefficients of MMSE are recalculated at each iteration. When cancellation is not involved, the computation of MMSE coefficients is done only once, because of H remaining unchanged. For MMSE 4 × 4 BPSK scheme, bit error rate of 10–2 at 30 dB is observed. In general, the most thorough procedure of the detection algorithm is the computation of the MMSE coefficients. Complexity arises in the calculation of the MMSE coefficients, when the antennas at the transmitting side are increased. However, while implementing adaptive MMSE receivers on slow channel fading, it is probable to recover the signal with the complications being linear in the antennas of transmitter node. The performance of MMSE and successive interference cancellation of MMSE are observed for 2 × 2 and 4 × 4 BPSK and QPSK modulation schemes. The drawback of MMSE SIC scheme is that the first detected signal observes the noise interference from (NT-1) signals, while signals processed from every antenna later observe less noisy interference as the process of cancellation progresses. This difficulty could be overcome by using OSIC detection method which uses successive ordering of the processed layers in the decreasing power of the signal or by power allocation to the signal transmitted depending on the order of the processing. By using successive scheme, a computation of NT delay stages is desired to bring out the abandoned process. The work also includes comparison of BER with various modulation schemes and number of antennas involved while evaluating the performance. MLD determines the Euclidean distance among the vector signal received and result of all probable transmitted vector signals with the specified channel H and finds the one with the minimum distance. Estimated results show that higher order of the diversity is observed by employing more antennas at both the receiving and transmitting ends. MLD with 8 × 8 binary phase shift keying (BPSK) scheme offers bit error rate near to 10^–4 for SNR (16 dB). By using Altamonti space ti.

It should come as no surprise that companies everywhere are pushing to get products to market faster. Missing a market window or a design cycle can be a major setback in a competitive environment. It should be equally clear that this pressure is coming at the same time that companies are pushing towards “leaner” organizations that can do more with less. The trends mentioned earlier are not well supported by current test and measurement equipment, given this increasingly high-pressure design environment: in order to measure signals across multiple domains, multiple pieces of measurement equipment are needed, increasing capital or rental expenses. The methods available for making cross-domain, time-correlated measurements are inefficient, reducing engineering efficiency. When only used on occasion, the learning curve to understand how to use equipment for logic analysis, time domain and RF spectrum measurements often requires an operator to re-learn each piece of separate equipment. The equipment needed to measure wide bandwidth, time-varying spectral signals is expensive, again increasing capital or rental expenses. What is needed is a measurement instrument with a common user interface that integrates multiple measurement capabilities into a single cost-effective tool that can efficiently measure signals in the current wide-bandwidth, time-correlated, cross-domain environments. The market of wireless communication using STBCs has large scope of expansion in India. Therefore, the proposed work has techno-commercial potential and the product can be patented. This project shall in turn be helpful for remote areas of the nearby region particularly in Gadchiroli district and Melghat Tiger reserve project of Amravati district, Nagjira and so on where electricity is not available and there is an all the time problem of coverage in getting the network. In some regions where electricity is available, the shortage is such that they cannot use it for peak hours. In such cases, stand-alone space diversity technique, STBC shall help them to meet their requirements in making connection during coverage problem, thereby giving higher data transmission rates with better QOS (quality of service) with least dropped connections. This trend towards wireless everywhere is causing a profound change in the responsibilities of embedded designers as they struggle to incorporate unfamiliar RF technology into their designs. Embedded designers frequently find themselves needing to solve problems without the proper equipment needed to perform the tasks.

Work is original.

The suggested work examines the latest developments such as the techniques employed for allocation of power, browser techniques, modern analysis and bandwidth efficiency of nonorthogonal multiple accesses (NOMA) in the network of 5G. Furthermore, the proposed work also illustrates the performance of NOMA when it is combined with various techniques of wireless communication namely network coding, multiple-input multiple-output (MIMO), space-time coding, collective communications, as well as many more. In the case of the MIMO system, the proposed research work specifically deals with a less complex recursive linear minimum mean square error (LMMSE) multiuser detector along with NOMA (MIMO-NOMA); here the multiple-antenna base station (BS) and multiple single-antenna users interact with each other instantaneously. Although LMMSE is a linear detector with a low intricacy, it performs poorly in multiuser identification because of the incompatibility between LMMSE identification and multiuser decoding. Thus, to obtain a desirable iterative identification rate, the proposed research work presents matching constraints among the decoders and identifiers of MIMO-NOMA.

To improve the performance in 5G technologies as well as in cellular communication, the NOMA technique is employed and contemplated as one of the best methodologies for accessing radio. The above-stated technique offers several advantages such as enhanced spectrum performance in contrast to the high-capacity orthogonal multiple access (OMA) approach that is also known as orthogonal frequency division multiple access (OFDMA). Code and power domain are some of the categories of the NOMA technique. The suggested research work mainly concentrates on the technique of NOMA, which is based on the power domain. This approach correspondingly makes use of superposition coding (SC) as well as successive interference cancellation (SIC) at source and recipient. For the fifth-generation applications, the network-level, as well as user-experienced data rate prerequisites, are successfully illustrated by various researchers.

The suggested combined methodology such as MIMO-NOMA demonstrates a synchronized iterative LMMSE system that can accomplish the optimized efficiency of symmetric MIMO NOMA with several users. To transmit the information from sender to the receiver, hybrid methodologies are confined to 2 × 2 as well as 4 × 4 antenna arrays, and thereby parameters such as PAPR, BER, SNR are analyzed and efficiency for various modulation strategies such as BPSK and QAM_j (j should vary from 8,16,32,64) are computed.

The proposed hybrid MIMO-NOMA methodologies are synchronized in terms of iterative process for optimization of LMMSE that can accomplish the optimized efficiency of symmetric for several users under different noisy conditions. From the obtained simulated results, it is found, there are 18%, 23% 16%, and 8% improvement in terms of Bit Error Rate (BER), Least Minimum Mean Squared Error (LMMSE), Peak to Average Power Ratio (PAPR), and capacity of channel respectively for Binary Phase Shift Key (BPSK) and Quadrature Amplitude Modulation (QAM) modulation techniques.

The main aim of this study is to elaborately examine the error correction technology for global navigation satellite system (GNSS) navigation messages and to draw a conceptual decision support framework related to the modernization of the GNSS and other systems.

The extensive simulation model developed in Matrix Laboratory (MATLAB) is used to evaluate the performance of forward error correction (FEC) codes such as Hamming, Bose–Chaudhuri–Hocquenghem, convolutional, turbo, low-density parity check (LDPC) and polar codes under different levels of noise.

The performance and robustness of the aforementioned algorithms are compared based on the bit length, complexity and execution time of the GNSS navigation message. In terms of bit error rate, LDPC coding exhibits more ability in the robustness of the navigation message, while polar code gives better results according to the execution time.

In view of future new GNSS signals and message design, the findings of this paper may provide significant insight into navigation message modernization and design as an important part of GNSS modernization.

To the best of the authors’ knowledge, this is the first study that conducts a direct comparison of various FEC algorithms on GNSS navigation message performance against noise, taking into consideration turbo and newly developed polar codes.

An overview of radio telemetry, concentrating on low power, short‐range systems which can be operated without equipment licences. Describes transmission mechanisms, aerials and the two main types of analogue modulation: amplitude modulation [AM] and frequency modulation [FM].Outlines the developments in radio data links and modulation schemes, the benefits of networks and the various methods of encoding data. Concludes that one of the biggest problems in radio telemetry is the different regulations across Europe making it virtually impossible to design a transmitter that is acceptable in more than one country. However, in Europe the situation is slowly changing, with new common standards for defining, evaluating and testing equipment coming into effect.

This paper aims to exploit an orthogonal space-time block code (OSTBC) and maximal ratio combining (MRC) techniques to evaluate error rate performance of multiple-input multiple-output system for different modulation schemes operating over single- and double-Weibull fading channels.

The authors provided a novel analytical expression for cumulative distribution function (CDF) of double-Weibull distribution in the form of Meijer-G function. They also evaluated probability density function (PDF) and CDF for single- and double-Weibull random variables. CDF-based closed-form expressions of symbol error rate (SER) are computed for the proposed systems’ design.

Based on simulation and analytical results, the authors have shown that double-Weibull fading which shows the cascaded nature of channel gives significantly poor SER performance compared to that of single-Weibull fading. Moreover, MRC offers an improved error rate performance compared to that of OSTBC. As the fading parameter increases for any modulation technique, the required signal-to-noise ratio (SNR) gap between single- and double-Weibull fading decreases. Finally, it is observed that the analytical results are a good approximation to simulation results.

For practical implication, the authors use a number of antennas at the base station, but solely to maximize performance, one can use receive diversity, i.e. MRC.

Using higher-order modulation (i.e. 16-QAM), 4 and 1 dB less SNR is required at high and less fading, respectively, in single-Weibull fading as compared to double-Weibull fading. Hence, at higher-order modulation, double-Weibull channel model performs better as compared to lower-order modulation.

The purpose of this work is to propose a new multi‐user detector which cascades the linear G‐SIC with some linear PIC stages to form a new linear hybrid multi‐user detector.

Multistage interference cancellation multi‐user detectors became an increasingly important area of research due to their relative low computational complexity. The performance comparison of the proposed linear HIC is studied and presented using matlab environment to investigate the bit error rates. For DS/CDMA system, each user is characterized by its own code. The signals from users are spread by appropriately design sequences and then transmitted over an AWGN channel with BPSK modulation.

By the cascade of the linear G‐SIC and the traditional PIC, a low complexity multi‐user detector is found capable of reducing the long detection delay compared with the linear G‐SIC. The advantages of the linear G‐SIC and PIC can be exploited substantially.

The paper proposes an algorithm that can combat the MAI with less complexity, and also can speed the convergence compared with other detectors.

The purpose of this paper is to analyse a novel technique for an efficient numerical approximation of systems of highly oscillatory ordinary differential equations (ODEs) that arise in electronic systems subject to modulated signals.

The paper combines a Filon‐type method with waveform relaxation techniques for nonlinear systems of ODEs.

The analysis includes numerical examples to compare with traditional methods such as the trapezoidal rule and Runge‐Kutta methods. This comparison shows that the proposed approach can be very effective when dealing with systems of highly oscillatory differential equations.

The present paper constitutes a preliminary study of Filon‐type methods applied to highly oscillatory ODEs in the context of electronic systems, and it is a starting point for future research that will address more general cases.

The proposed method makes use of novel and recent techniques in the area of highly oscillatory problems, and it proves to be particularly useful in cases where standard methods become expensive to implement.