Search results

This study aimed to investigate the collective effects of bending load and hygrothermal aging on glass fibre-reinforced plastics (GFRP) due to the fact that stress and water absorption is inevitable during GFRP applications.

The water boiling method was used to study the moisture absorption, desorption behaviour and evaluate the performance of GFRP laminates under loading in this article. The moisture diffusion of laminates is characterized in three aging conditions (25°C, 45°C and 65°C water), along with three levels of bending load coefficients (0, 0.3 and 0.6). The moisture diffusion coefficients are determined through the curve fitting method of the experimental data of the initial process, based on the Fickian diffusion model. Moreover, the laminates’ performance is further discussed after adequate environmental aging and loading.

It was found that moisture absorption is promoted by the presence of bending load and boiling during this study. The absorption diffusion coefficient and moisture equilibrium content of the specimens increased with an increasing loading ratio and temperature. The bending strength of the laminate varied according to a contrary trend. Furthermore, the desorbed moisture content is found to be much higher after higher levels of bending load because it is harder to desorb the moisture in the interfaces and micro cracks.

Collective effects of bending load and hygrothermal aging promote the absorption and result in accelerating property degradation of GFRP. It is significant to focus on these effects on the failure of GFRP.

A novel unit was designed to simulate the various loading acted on containers in this work.

Gives a bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore aims to give the reader an encyclopaedic view on the subject. The bibliography at the end of the paper contains 2,025 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1992‐1995.

The aim of this paper is to study the effect of pressure angle and helix angle on bending stress at the root of helical gear tooth under dynamic state. Gear design is a highly complex process. The consistent demand to build low-cost, quieter and efficient machinery has resulted in a gradual change in gear design. Gear parameters such as pressure angle, helix angle, etc. affect the load-carrying capacity of gear teeth. Adequate load-carrying capacity of a gear is a prime requirement. The failure at the critical section because of bending stress is an unavoidable phenomenon. Besides this fact, the extent of these failures can be reduced by a proper gear design. The stresses produced under dynamic loading conditions in machine member differ considerably from those produced under static loading.

The present work is intended to study the effect of pressure angle and helix angle on the bending stress at the root of helical gear tooth under dynamic state. The photostress method has been used as experimental methods. Theoretical analysis was carried out by velocity factor method and Spott’s equation. LS DYNA has been used for finite element (FE) analysis.

The results show that experimental method gives a bending stress value that is closer to the true value, and bending stress varies with pressure angle and helix angle. The photostress technique gives clear knowledge of stress pattern at root of tooth.

The outcomes of this work help the designer use optimum weight-to-torque ratio of gear; this is ultimately going to reduce the total bulk of the gear box.

Tapered steel sections are widely used in house building design due to their structural efficiency and aesthetic appearance. Due to the practical usage of web tapering specifications in the metal building industry, fabrication and material expenses are analyzed to achieve geometric and economic productivity. The purpose of this study is to investigate the effectiveness of utilizing web profiles with openings in reducing the weight of steel beams.

In this paper, the nonlinear analysis of the bending behavior of a tapered steel section with an opening was studied by finite element analysis. The results were then compared with those of the tapered steel section without an opening in terms of displacement and yield moment.

The bending capacity of a tapered steel section was analyzed using finite element analysis. Results showed that the tapered steel section without openings had a higher bending capacity compared to the section with various sizes of web openings. The results also showed that decreasing the number of openings would increase the bending capacity, whereas increasing the size of the opening would decrease it. The difference in the yield moment between the tapered steel section with and without openings was only 15.818%. A total of 60 nonlinear analyses were conducted to investigate the effect of the number and size of web openings, flange thickness and web thickness on the bending behavior. However, this study showed that web opening with octagon shape and 0.6D size of web opening, where D is the depth of section, showed the best section in terms of yield moment and volume reduction compared to other opening size and shape.

It is also found that tapered steel section has better moment resistance in thicker flange and web. The study is valuable for engineers and designers who work with steel structures and need to optimize the performance of tapered steel sections with web openings.

A DSIR Sponsored Research Programme on the Development and Application of the Matrix Force Method and the Digital Computer. This work presents a rational method for the structural analysis of stressed skin fuselages for application in conjunction with the digital computer. The theory is a development of the matrix force method which permits a close integration of the analysis and the programming for a computer operating with a matrix interpretive scheme. The structural geometry covered by the analysis is sufficiently arbitrary to include most cases encountered in practice, and allows for non‐conical taper, double‐cell cross‐sections and doubly connected rings. An attempt has been made to produce a highly standardized procedure requiring as input information only the simplest geometrical and elastic data. An essential feature is the use of the elimination and modification technique subsequent to the main analysis of the regularized structure in which all cutouts have been filled in. Current Summary A critical historical appraisal of previous work in the Western World on fuselage analysis is given in the present issue together with an outline of the ideas underlying the new theory.

The main purpose of this study was to propose theoretical calculation models to evaluate the theoretical bending strengths of welded wide-flange section steel beams with local buckling at elevated temperatures.

Steady-state tests using various test parameters, including width-thickness ratios (Class 2–4) and specimen temperatures (ambient temperature, 400, 500, 600, 700, and 800°C), were performed on 18 steel beam specimens using roller supports to examine the maximum bending moment and bending strength after local buckling. A detailed calculation model (DCM) based on the equilibrium of the axial force in the cross-section and a simple calculation model (SCM) for a practical fire-resistant design were proposed. The validity of the calculation models was verified using the bending test results.

The strain concentration at the local buckling cross-section was mitigated in the elevated-temperature region, resulting in a small bending moment degradation after local buckling. The theoretical bending strengths after local buckling, evaluated from the calculation models, were in good agreement with the test results at elevated temperatures.

The effect of local buckling on the bending behaviour after the maximum bending strength in high-temperature regions was quantified. Two types of calculation models were proposed to evaluate the theoretical bending strength after local buckling.

The purpose of this study is to investigate the effect of structural deformations and bend angle on plastic collapse load of pipe bends under an in-plane closing bending moment (IPCM). A large strain formulation of three-dimensional non-linear finite element analysis was performed using an elastic perfectly plastic material. A unified mathematical solution was proposed to estimate the collapse load of pipe bends subjected to IPCM for the considered range of bend characteristics.

ABAQUS was used to create one half of the pipe bend model due to its symmetry on the longitudinal axis. Structural deformations, i.e. ovality (C_o) and thinning (C_t) varied from 0% to 20% in 5% steps while the bend angle (ø) varied from 30° to 180° in steps of 30°.

The plastic collapse load decreases as the bend angle increase for all pipe bend models. A remarkable effect on the collapse load was observed for bend angles between 30° and 120° beyond which a decline was noticed. Ovality had a significant effect on the collapse load with this effect decreasing as the bend angle increased. The combined effect of thinning and bend angle was minimal for the considered models and the maximum per cent variation in collapse load was 5.76% for small bend angles and bend radius pipe bends and less than 2% for other cases.

The effect of structural deformations and bend angle on collapse load of pipe bends exposed to IPCM has been not studied in the existing literature.

This paper aims to investigate the responses of single piles and pile groups due to tunneling-induced ground movements in a two-layered soil system. The analyses mainly focus on the additional single pile responses in terms of bending moment, lateral deflection, axial force, shaft resistance and pile settlement. Subsequently, a series of parametric studies were carried out to better understand the responses of single piles induced by tunneling. To give further understanding regarding the pile groups, a 2 × 2 pile group with two different pile head conditions, namely, free and capped, was considered.

Using the PLAXIS three-dimensional (3D) software, a full 3D numerical modeling is performed to investigate the effects of ground movements caused by tunneling on adjacent pile foundations. The numerical model was validated using centrifuge test data found in the literature. The relevance of the 3D model is also judged by comparison with the 2D plane strain model using the PLAXIS 2D code.

The numerical test results reveal that tunneling induces significant displacements and internal forces in nearby piles. The magnitude and distribution of internal forces depend mainly on the position of the pile toe relative to the tunnel depth and the distance between the pile and the vertical axis of the tunnel. As the volume loss increases from 1% to 3%, the apparent loss of pile capacity increases from 11% to 20%. By increasing the pile length from 0.5 to 1.5 times, the tunnel depth, the maximum pile settlement and lateral deflection decrease by about 63% and 18%, respectively. On the other hand, the maximum bending moment and axial load increase by about 7 and 13 times, respectively. When the pile is located at a distance of 2.5 times the tunnel diameter (Dt), the additional pile responses become insignificant. It was found that an increase in tunnel depth from 1.5Dt to 2.5Dt (with a pile length of 3Dt) increases the maximum lateral deflection by about 420%. Regarding the interaction between tunneling and group of piles, a positive group effect was observed with a significant reduction of the internal forces in rear piles. The maximum bending moment of the front piles was found to be higher than that of the rear piles by about 47%.

Soil is a complex material that shows differently in primary loading, unloading and reloading with stress-dependent stiffness. This general behavior was not possibly being accounted for in simple elastic perfectly plastic Mohr–Coulomb model which is often used to predict the behavior of soils. Thus, in the present study, the more advanced hardening soil model with small-strain stiffness (HSsmall) is used to model the non-linear stress–strain soil behavior. Moreover, unlike previous studies THAT are usually based on the assumption that the soil is homogeneous and using numerical methods by decoupled loadings under plane strain conditions; in this study, the pile responses have been exhaustively investigated in a two-layered soil system using a fully coupled 3D numerical analysis that takes into account the real interactions between tunneling and pile foundations. The paper presents a distinctive set of findings and insights that provide valuable guidance for the design and construction of shield tunnels passing through pile foundations.

The purpose of this paper is to quantify the combined effect of shape distortion and bend angle on the collapse loads of pipe bends exposed to internal pressure and in-plane closing bending moment. Non-linear finite element analysis with large displacement theory was performed considering the pipe bend material to be elastic perfectly plastic.

One half of the pipe bend model was built in ABAQUS. Shape distortion, namely, ovality (Co) and thinning (Ct), were each varied from 0% to 20% in steps of 5% and bend angle was varied from 30° to 180° in steps of 30°.

The findings show that ovality has a significant impact on collapse load. The effect of ovality decreases with an increase in bend angle for small thickness. The opposite effect was observed for large thickness pipe bends. The influence of ovality was more for higher bend angles. Ovality impact was almost negligible at certain internal pressure denoted as nullifying point (NP). The latter increased with an increase in pipe bend thickness and decreased with increase in pipe bend radius. For small bend angles one NP was observed where ovality impact is negligible and beyond this point the ovality effect increased. Two NPs were observed for large bend angles and ovality effect was maximum between the two NPs. Thinning yielded a minimal effect on collapse load except for small bend angles and bend radii. The influence of internal pressure on thinning was also negligible.

Influence of shape distortions and bend angle on collapse load of pipe bend exposed to internal pressure and in-plane closing bending has been not revealed in existing literature.

A two‐spar cantilever box beam with forty‐five degrees sweep and oblique ribs placed parallel to the root clamping section was the subject of a series of static tests. Stress and strain distributions were determined, primarily in a region distant from the root and tip disturbances, to permit a stringent comparison with three well‐known swept wing theories and the simple theory of bending. Torsional and flexural stiffnesses were also measured and compared with these theories. The sequence of calculation for each method is presented and it is found that two of the theories provide accurate predictions of the stresses, strains and stiffnesses. The influence of rivet slip and rivet flexibility on the stiffnesses of the box is mentioned. As a secondary aim of the investigation, the distribution of normal and shear strain has been measured in the cover skin and spar webs at the root connexion. The design of swept box examined has been the subject of research in a number of establishments and a review of this other work is included.