Search results

AA2014 is a copper-based alloy and is typically used for production of complex machined components, given its better machinability. The purpose of this paper was to study the effects of variation in weight percentage of ceramic Al₂O₃ particulates during electrical discharge machining (EDM) of stir cast AA2014 composites. Scanning electron microscopy (SEM) examination was carried out to study characteristics of EDMed surface of Al₂O₃/AA2014 composites.

The effect of machining parameters on performance measures during sinker EDM of stir cast Al₂O₃/AA2014 composites was examined by “one factor at a time” (OFAT) method. The stir cast samples were obtained by using three levels of weight percentage of Al₂O₃ particulates, i.e. 0 Wt.%, 10 Wt.% and 20 Wt.% with density 1.87 g/cc, 2.35 g/cc and 2.98 g/cc respectively. Machining parameters varied were peak current (1-30 amp), discharge voltage (30-100 V), pulse on time (15-300 µs) and pulse off time (15-450 µs) to study their influence on material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR).

MRR and SR decreased with an increase in weight percentage of ceramic Al₂O₃ particulates at the expense of TWR. This was attributed to increased microhardness for reinforced stir cast composites. However, microhardness of EDMed samples at fixed values of machining parameters, i.e. 9 amp current, 60 V voltage, 90 µs pulse off time and 90 µs pulse on time reduced by 58.34, 52.25 and 46.85 per cent for stir cast AA2014, 10 Wt.% Al₂O₃/AA2014 and 20 Wt.% Al₂O₃/AA2014, respectively. SEM and quantitative energy dispersive spectroscopy (EDS) analysis revealed ceramic Al₂O₃ particulate thermal spalling in 20 Wt.% Al₂O₃/AA2014 composite. This was because of increased particulate weight percentage leading to steep temperature gradients in between layers of base material and heat affected zone.

This work was an essential step to assess the machinability for material design of Al₂O₃ reinforced aluminium metal matrix composites (AMMCs). Experimental investigation on sinker EDM of high weight fraction of particulates in AA2014, i.e. 10 Wt.% Al₂O₃ and 20 Wt.% Al₂O₃, has not been reported in archival literature. The AMMCs were EDMed at variable peak currents, voltages, pulse on and pulse off times. The effects of process parameters on MRR, TWR and SR were analysed with comparisons made to show the effect of Al₂O₃ particulate contents.

This study aims to calculate the corporate social responsibility (CSR) expenditure made by companies as per the provisions of Section 135 of Companies Act 2013 and check the status of compliance/non-compliance of these provisions in the mandatory regime of CSR.

Based on a sample of top 500 Indian companies listed on Bombay Stock Exchange, the study compares the CSR expenditure required to be incurred by companies with the actual CSR expenditure made by them over a time span of seven years and calculates the extent of surplus or deficit attained by them starting from the year of inception of CSR provisions, 2014–2015, till the most recent year, 2020–2021.

The findings indicate that the average CSR expenditure made by Indian corporate sector is less than the mandatory requirement. More than half of the companies do not comply with the CSR regulations of the country. Even the “Most Profitable” companies fail to contribute the minimum required amount towards social activities akin to their counterparts in the “Less” and “Least” profitable categories.

The disobedience towards the statutory provisions implies that Indian companies are non-compliant towards CSR guidelines despite the regulative institutional pressure that makes CSR a mandatory practice to legitimise it.

The study contributes to the CSR literature in the light of the transformed regulative institutional environment in India. It includes a comprehensive analysis of compliance of companies with the revised statutes over all the years since the inception of new mandatory guidelines on CSR till the most recent time period on a representative sample, thus, making the findings robust and generic with respect to India.

The increase of Islamophobia-inspired hate crimes toward Sikh Americans led the Sikh Coalition of America and the National Council for the Social Studies to request social studies educators to conduct a content analysis on the presentation of Sikhism in social studies textbooks. The Sikh Coalition hopes to use the findings of such research to encourage more appropriate inclusion about the religion in textbooks by the leading publishing companies and as a legitimate social studies subject of instruction in the state standards for all 50 states. The paper aims to discuss this issue.

The incorporation of critical pedagogy, as a tool of critical multiculturalism, serves as the theoretical design of this study. Content analysis serves as the method of research for this study. The authors also employed an online survey to determine the scope of religious literacy of the pre-service teachers with regard to Sikhism before the conducting of content analysis of social studies textbooks for the presentation of Sikhism.

The current presentation of Sikhism in social studies textbooks has the potential to help fuel the Islamophobia that Sikh Americans now face. The authors found that the pre-service teachers possess little religious literacy regarding Sikhism. Furthermore, from the content analyses, the authors found that a total of 21 out of the sample of 32 textbooks (5 elementary, 11 middle grades and 16 high school) mention Sikhism. Eight textbooks include a mention of the origins of Sikhism. Nine textbooks misidentify the religion as a blending of Hinduism and Islam. Nine textbooks mention the religion in relation to the assassination of Indira Gandhi.

The originality of this research led the authors to find that the very limited and inaccurate information we found present in the most-used textbooks for elementary, middle grades and high school social studies made the employing of inferential statistics like correlation difficult. Also, the authors found from the literature that research addressing Islamophobia in the classroom has centered on the role of licensed teachers only. The research gives a model to how pre-service teachers may address Islamophobia in the classroom and also gain religious literacy regarding Sikhism.

The rise of Islamophobia-inspired violence toward students of South Asian descent has led to the call to address this matter. The research introduces a method to how social studies education professors may help engage their pre-service teachers in proactively addressing Islamophobia. Social studies professors have a responsibility to help promote social justice through critical pedagogy that explores the religious literacy of their pre-service teachers beyond Buddhism, Christianity, Hinduism, Islam and Judaism.

The Sikh Coalition, by telephone, has formally acknowledged to the authors that the textbook research has been the most extensive they have received since making their joint request with the National Council for the Social Studies. They have used the research to successfully convince the state education boards of Texas and recently Tennessee to adopt the inclusion of Sikhism in social studies content. More Americans, at a young age, need to learn about Sikh culture, so they are less likely to develop prejudicial ideas about Sikh Americans and commit violent acts of religious-based discrimination.

The research is extremely rare. To date, no one else in the country has conducted research on the presentation of Sikhism in textbooks to the extent that the authors have. The authors hope that the research will encourage more dialogue and further research. The authors hope that the research will help prevent further acts of religious-based violence toward followers of the world’s sixth largest religion.

The prolonged army rule in the country has affected the policymaking procedure of the state. Specifically, defence and foreign policies of the country are normally decided by the armed forces of Pakistan as per their own priorities, which is against the norms of democratic culture and supremacy of the civilian rule.

The control of important decision-making process in the hands of the armed forces has generated an arms race in the subcontinent. The major portion of the national budget is being spent on the defence forces and other sectors such as education and health and social welfare are not getting their due share from the revenue of the country. The continued sense of insecurity and animosity with neighbour countries, especially India, has resulted in speeding the acquisition of sophisticated arms in the country.

This research discusses the effects of the military's role in the decision-making of the country and its impacts on the relations between India and Pakistan. The confidence building measures and peacemaking process in South Asia is dependent on the attitude of the military of both the countries.

At every period of time marked by years, the seasons by turns and twists in history, among country folk especially, the years of great storms and hard winters; in law enforcement, the passing of some far‐reaching, profound statutory measure, there is this almost universal tendency to look back—over your shoulder‐assessing changes, progressive or otherwise, discerning trends and assaying prospects. We are about to emerge from the seventies—battered but unbowed!—into the new decade of the eighties, perhaps with a feeling that things can only get better.

The learning outcomes of this paper is as follows: to explain the importance of rationalizing business operations to achieve efficiencies. To explain the importance of constantly re-inventing the product portfolio and the business for the survival and growth of the business. To discuss the use of product-market expansion strategies as used by businesses for growth and sustainability. To evaluate the internal challenges faced by a company as they adopt business strategies for business growth. To discuss a firm’s strategy to exploit significant opportunities in an evolving business environment.

Panasonic Life Solutions India Limited (PLSIND) an electrical products company with operations in India – an emerging market has set a Vision 2022 to achieve INR 69.21bn revenue target by the year 2022. PLSIND is marketed through the distributor business to consumer sales channel. To achieve the new growth targets, it was imperative for them to expand the product portfolio and explore marketing through the new business to business (B2B) and business to government (B2G) sales channels. Dinesh Aggarwal the Joint Managing Director of PLSIND was tasked with this responsibility. Both propositions depicted attractive business potential but at the same time came with additional risks of a longer sales/revenue cycle. PLSIND to a certain extent had ventured into new business projects with the launch of home automation, solar solutions for industries and smart street lighting business projects. In 2019, they also made a modest beginning by achieving revenues of INR 3.4bnn (constituting 10% of their aggregate revenues of INR 34bn) from B2B/B2G sales channels. Aggarwal believed that this was a good beginning. However, to achieve 2022 growth targets, they had to aggressively move forward with the new business strategy. Aggarwal had to work with the management team to gain acceptance and then to manage these additional risks for growth that came with this new business strategy. How could he win the confidence of the management team? How could he best reorganize the business teams and processes internally to enhance the required operational efficiencies for business growth?

This case is designed for business students at the MBA or executive MBA level courses.

Teaching notes are available for educators only.

CSS 11: Strategy.

A highly significant action taken by the Minister of Agriculture, Fisheries and Food, reported elsewhere in this issue, could well result in important advances in surveillance and probably legislative control over enforcement of certain aspects of EEC legislation in the Member‐states. The Minister has sent an urgent request to the Commission in Brussels to dispatch inspectors to each country, including the United Kingdom, to examine and report on the standards of inspection and hygiene with detailed information on how the EEC Directive on Poultry Meat is being implemented. Information of the method of financing the cost of poultrymeat inspection in each country has ben requested. The comprehensive survey is seen as a common approach in this one field. The Minister requested that the results of the inspectors' reports should be available to him and other Member‐states.

Parts that are to be used in aircraft, satellites, automobiles and ships should have sound microstructure. Components made from AA6082/Si₃N₄ and AA6082/SiC composites are in demand from industries. Hence, these components are to be fabricated by suitable technique at the appropriate value of process parameters. The purpose of this paper is Microstructure analysis of AA6082/Si3N4 and AA6082/SiC composites

AA6082/Si₃N₄ and AA6082/SiC composites are successfully fabricated using the stir casting process. Their microstructures have been analyzed. This has been done at different magnification. The effect of the addition of Si₃N₄ and SiC particles in the 6082 aluminum alloy is investigated. Microstructure of AA6082/Si₃N₄ and AA6082/SiC composites are also compared. Results show that Si₃N₄ and SiC particles have good wettability with AA6082. These reinforcement particles are homogeneously distributed in the matrix of AA6082.

There are no adverse effects of reactions in the microstructure of AA6082/Si₃N₄ and AA6082/SiC composites. There is not much difference between the distribution and interfacial characteristics of Si₃N₄ and SiC particles. AA6082/Si₃N₄ and AA6082/SiC composites have good properties. This is high strength at low density. Due to which they become suitable for the aircraft and space industry. So far, SiC, Al₂O₃ and tungsten carbide have been mostly used as reinforcements with different grades of aluminum alloy.

Not much experimental work is found with Si₃N₄ and SiC particles as reinforcement with AA6082. The novelty of this research work is that an effort has been made to fabricate AA6082/Si₃N₄ and AA6082/SiC composites at such values of process parameters, by stir casting process, so that sound and defect free microstructure is obtained. Microstructure of AA6082/Si₃N₄ and AA6082/SiC composites is also compared, to find which is better.

This article presents four newly developed mathematical models representing non‐maintained parallel systems with hardware failures, common‐cause failures and human error. The Markov method was used to develop expressions for parallel system state probabilities, system reliability and mean time to failure (MTTF). System reliability and MTTF plots are shown. These plots clearly show the effect of common‐cause failures and human error on system reliability.

A newly developed model for performing reliability and availability analysis of mechanical devices subject to multiple failure modes is presented. Using this model, reliability analyses of mechanical devices such as brakes, bearings, engines, fans, gears, generators, heat exchangers and pumps are developed. Real life failure rate data for these devices are obtained from various sources and are used in their reliability analyses. Principal failure modes of these devices are identified and expressions for reliability, state probabilities, mean time to failure and variance of time to failure are developed. For known field failure data reliability and state probability plots are shown.